Share your ROUTE v2.0 Experience

@D&D congratulation
Did you encountered DHCP relay information D&D?

About ACL d&d in my opinion:
**ACL**
reflexive – must be named
standard – range 1300-1399
extended – closest to (source) device
time-based – access to device at certain times
dynamic – telnet..

so what is the correct answer for satax# distance 89 51.51.51.0 0.0.0.255 OR distance 90 51.51.51.51 0.0.0.255

Hey Waz : distance 90 makes no sense because we have a AD from 90…see below… D 10.10.10.10 [90/12569] via 52.52.52.52, … [90/12569] via 51.51.51.51 @ TIMMY666 : Are you sure about the command …. was it really 51.51.51.0 with 0.0.0.0

congrats both , for passing your Route today :o)

can someone please check which from both is correct, I guess it will be the first one…

3.) **ACL**
reflexive – must be named
standard – range 1300-1399
extended – telnet …
time-based – access to device at certain times
dynamic – closest to device

or

DND:
reflexive – must be named
standard – range 1300-1399
extended – apply closest to the source or origin
time-based – access to device at certain times
dynamic – it needs telnet to authenticate

@both can you please check my pdf and maybe you can remember you if this pdf is valid with new ruestions…
https:// anonfile.com/7dS6I8d5ba/Q_A_1 pdf
Thanks Guys in advance for you help !

next_try below is correct

DND:
reflexive – must be named
standard – range 1300-1399
extended – apply closest to the source or origin
time-based – access to device at certain times
dynamic – it needs telnet to authenticate

@Next_try
Yes, it is still valid. Majority of my questions are in that pdf.

Goodluck!

Question about satax#
so the answer is distance 89 51.51.51.0 0.0.0.0??

A.Satax#
B.Satax# distance 89 51.51.51.0 0.0.0.0
C.Satax#
D.Satax#
E.Satax#

@weeee distance eigrp 89 170
this is another command and work for all routes, and not permit to select the route which apply.

distance 89 51.51.51.51 0.0.0.0 is the same that I’d choose!! :-)

guys what is the correct answer for :-
If you configure one router in your network with the auto-cost reference-bandwidth100 command, which
effect on the data path is true?
A. The data path remains the same for all links
B. The data path changes for 10Mbps links only
C. The data path changes for all links
D. The data path changes for 10Gbps links only

digital tut says C but all dumps says A

auto-cost reference-bandwidth 100 is a default config that is put implicitly in ospf process when it starts, it means that the cost of 100mb/s link will be = 1, so if you put this command explicitly it won’t change anything in your topology, the answer A is correct.

Hello, have you more information about this question??? Or this answer is ok for you?
Q: Another diagram that I have been thinking about was between 2 routers and they had an eigrp protocol running between- the question was that they can ping between them with no problem but when they are trying through the vrf connection it doesn’t work, what’s wrong? Which command to put on both routers to make it work?
a. rd 1:100 both
‎b. Network with a 255.255.240.0
‎c. autonomous-system 100
‎d. Don’t remember
Answer: C

Q: ‎a diagram that I was thinking a lot of was between 3 routers R1-R2-R3 (sound kind of similar to a new question that has been posted over here) which Eigrp 100 is configured on all of them. The router in the middle (R2) has his loopback put in shut and the router on the right is a stub (R3).
The Question was :
Who would get the query message for that loopback that has been put in shut
‎a. The feasible successors’ routers would get the query — that’s what I choosen
b.‎ R1 would request the query
c.‎ R1 and R3 would request the query
d.‎ R3 would request the query
Answer: B is that correct??? R3 is a Stub and for this reason he doesn’t get the Queiry?

@Alex
thanks

@Rizwan

Are you sure about the value 100 being part of the question? I’ve seen it with a bigger value which would change the answer to the question.

@ D&D Congraaats

Can someone please share the CCNP ROUTE(300 -301)

i am taking my Exams in 3 weeks Time…

@Sco yes this question contains 100 and some questions contain 1000 and some 10000 in dumps

@Sco yes because this question contains the value 100 and some has 1000 and some as 10000 in dumps

Hi all,

i’ve just pass my exam today…a lot of new questions I’ve never seen here about frame relay, NTP, one question about BGP table (choose the best path or something), vrf lite&EVN,
Labs are the same (eigrp stub, eigrp and ospf eval)

Anyway just study, ì it should be easy…
goodluck!

@WellDone
What DND did you get?

@WellDone

Congrats. Sounds like you had some of the same questions that popped up when I tested.

@WellDone
Could you share with us this new question if you remember it

I’ve just seen that most of them are added in updated question part 3 section.
about question 8, it was different, it asked for which table should be flushed after a clear ip route (something like this) another strange one was on cam value/arp value about flooding..don’t remember exactly.
DND acl, frame relay parameters, frame relay int config, aaa commands…ummm that’s all

Bye

How to set up IP SLA to monitor jitter between the certain limits? <= (it’s jitter now, not bandwidth)
A. Timeout (not timer)
B. Frequency
C. Threshold
D. Queue-limit
Answer: ?

Can someone say the correct answer and explain it?
Thanks!

Please anyone provide link to download updated ROUTE dumps.

Hi all, I passed the exam couple of days ago :) I will update you guys soon with what I got.

The enterprise network WAN link has been received several denial of service attacksfrom both IPv4 and IPv6
sources. Which three elements can you use to identify an IPv6 packet via its header, in order to filter future
attacks?(Choose three)

A. Traffic Class
B. Source address
C. Flow Label
D. Hop Limit
E. Destination Address
F. Fragment Offset

Answer : ACD or BCE
Please ,

@ next_try

QUESTION 74
what are two rules for compacting IPV6 address?
A. every 16-bits segment that consists of all zeroes can be represent with a single 0
B. the trailling zeores in any 16-bit segment do not have to be written
C. the leading zeroes in any 16-bi segment do no have to be written
D. any single, continuos string of one mor 16-bits segment that consists of all zeroes can be represet with
a double ::
E. the maximun number of time a double colon can replace a 16-bit segment that cosists of all zeroes is
two
F. two zeroes in the middle of any 16-bit segme do not have to be written

Answer should be A&C because D doesn’t says that the double:: should be used only once in an ipv6 address with that answer you can say that an use it twice or more.

@ Everyone
I passed with good marks and here is what I can say about the exam.

EIGRP Stub Lab: was not able to get 2 subnets, this was mentioned earlier.. Maybe a bug?
EIGRP Simlet: had some commands that were not usable again mentioned earlier.
PBR was as described.

There was a question that ask ” IPv6 using a T1 but then changes to Frame-Relay. What is needed for the change”?

Most of the questions have been posted here some rephrased but not to much.

Do not just study the dump, know the content and you will be okay.

DND
AAA, DHCP, Frame-Relay LMI
Note some changes to the wording on the drag and drops

FYI took exam yesterday. EIGRP stub sim, was not able to get down to 2 subnets. This must be a bug.

Hello, Can some one help me, i have my second try exam in 1 hour…
Are those questions OK?

Q: Another diagram that I have been thinking about was between 2 routers and they had an eigrp protocol running between- the question was that they can ping between them with no problem but when they are trying through the vrf connection it doesn’t work, what’s wrong? Which command to put on both routers to make it work?
a. rd 1:100 both
‎b. Network with a 255.255.240.0
‎c. autonomous-system 100
‎d. Don’t remember
Answer: C

Q: ‎a diagram that I was thinking a lot of was between 3 routers R1-R2-R3 (sound kind of similar to a new question that has been posted over here)
which Eigrp 100 is configured on all of them. The router in the middle (R2) has his loopback put in shut and the router on the right is a stub (R3).
The Question was : Who would get the query message for that loopback that has been put in shut
‎a. The feasible successors’ routers would get the query — that’s what I choosen
b.‎ R1 would request the query
c.‎ R1 and R3 would request the query
d.‎ R3 would request the query
Answer: B is that correct??? R3 is a Stub and for this reason he doesn’t get the Queiry?

plz share the lastest dumps of CCNP 300-101 abdulrehmandwp @ gmail dot com

Sorry for the late reply guys.

Here are the new questions i got on my test
Other questions are already covered in the comments before:

1.question about ipv6 EIGRP configuration

1-route advertisements are configured at the router global configuration
2-route advertisments are configured at the interface configuration–>chose
3-an ipv6 router ID
4-uses link-local ip address for route advertisments–>chose
5-ipv6 eigrp uses only the configured ipv6 global addresses for communication
6-…other wrong option

2.question about uRPF configuration (2 answers)

1-the first answer i dont remember but is really easy to figure out —>correct
2-configured at the interface level —>correct
3-configured at global configuration
4-other option

3.Technology used with EVN

1-MPLS
2-BGP
3-other option
4-other option
*Chose BGP to be honest but probably not the right answer

4.Which BGP option is required when load sharing over multiple equal-bandwidth parallel
links from a single CE router to a single ISP router over eBGP? Select the best response.

A. eBGP Multipath –>chose
B. eBGP Multihop
C. BGP Synchronization
D. Public AS numbers
* This question is in Dexter but answer is B,i got full mark in that section
so answer A is correct

4-Question 127 form Dexter, Refer to the exhibit. Which option prevents routing updates from beingsent to the DHCP router, while still allowing routing update messages to flow to the Internet router and the distribution switches?

The answers used access-list not passive interfaces
The 2 tricks about the question are:
1-some options have the AL configured
at the router configuration not the interface,
2-the ACL should be applied at the core router not the DHCP router
as the question says “prevent it from *being sent*”

5- question with a 3 router figure, the loop back on the middle
router is shut down what happens:(R3 configured as stub)
R1-R2-R3 –> i got 100% in that section so i am sure of the correct answer

1-R1 Will get the query about the lost route from R2 –>correct answer
2-R1 and R3 will get the query
3-query will be sent to the Feasible successors
4-other option

6- what does the command show ip vrf purple TOPOLOGY shows:

1- shows the feasible successors for a specific route table–>chose
2-other options
3-other options
4-other options

7-the command show ip flow export shows:

1-sent states and statistics
2-local states and statistics–>chose
3-other option
4-other option

8-one statement is coorect about syslog

1-uses udp port 514
2-other options
3-other options
4-other options

9-There was one one more question with a missing command on EIGRP vrf configuration:

1-configure autonomous system 100 on both routers
2-other options
3-other options
4-other options

10-The question regarding the new DHCP DnD:

ip dhcp relay information option –>automatically add the circuit identifier suboption and the remote ID suboption
ip dhcp relay information check –>check that the relay agent information option in forwarded BOOTREPLY messages is valid
ip dhcp relay information policy–>Configures the reforwarding policy for a DHCP relay agent
ip dhcp relay information subscriber-id–>enable an ISP to add a unique identifier
ip dhcp relay information trusted-sources–>configures interfaces on a router as trusted sources
ip dhcp relay information–> configured in global configuration mode applies to all interfaces

that’s all guys wish you good luck on your exams

@HanSolo
Thank you for updating us

@HanSolo Thank you so much!

@HanSolo
Tnx mate.

@HanSolo : Thx a lot for sharing :o) much appreciated !!

@HanSolo: Congratulation and thanks

@All guys when CCNP exam gonna change totally? and new version comes? plz reply thank you

does someone have a good plan how I can store the “AAA Authentication for ppp” in my brain ?!
meaning the D&D…
if-needed
krb5
Password Authen
local
none
etc…….

So thats cisco nonsense !!! These exams are far away from the reality !

I passed today
many new questions
dump is not enough, my advise you should understand and memorize all topics,
Good Luck for all

I have passed my exam 8×× was my second attempt
Lots of new questions don’t just rely on the dumps as I did
Today I got dchp DND which totally different as stated above
It had circuit id and virtual id

Don’t waste your money by just reading dumps it will be difficult to Pass. . Know the concepts you will Pass easily

Examination is playing with us now they squeezin and jumbling the questions need a lot of time and brain to understand

Thanks to Digitaltut and all the members in this forum
All the best to you all
I’m off from here now. .

May God ‘s peace and blessings be upon you all

@ Waz : congrats for passing it ! Please be so kind and share all known details with us !
What LABs and D&D did you get ?
What do you think about the (new) questions ?

Hello everyone! Can you please send me the latest dumps on my email ogoheinz at gmail dot com.
Thank you very much!

Sorry, i sent wrong mail in last post… Can you please send me the latest dumps on my email ogoheinz at yahoo dot com. Thank you!!!

Hello,
Can anyone tell how many questions are on the exam?

Questions what I remember from exam:

Q.What two authentication methods do EIGRP use? (Choose two)
A. TKIP
B. MD5
C. WPA
D. Plain Text
Answer: B D

Q. Which two of the following options are true about NetFlowv9? (Choose two)
A. IEEE standard
B. IETF standard
C. ingress only
D. egress only
E. ingress/egress
Answer: B, E

Q. Question mentioned recently about how to prefer the route 51.51.51.51 over another EIGRP route
Answer: distance 89 51.51.51.51 0.0.0.0

Q. How to set up IP SLA to monitor jitter between the certain limits? <= (it’s jitter now, not bandwidth)
A. Timeout (not timer)
B. Frequency
C. Threshold
D. Queue-limit
Answer: C

Q.Which cisco Express Forwarding component(s) contain forwarding information? (forwarding information, they changed it)
A. FIB, adjacency table (this option was not in the exam)
B. adjacency table.
C. FIB, RIB , Adjanceny table
D. FIB
E. RIB
My Answer is: I would go with 'FIB, adjacency' but that choice was not included in the exam.
I chose B.

Q.What is the NHRP role in DMVPN? (Choose 2)
A. obtains the next-hop to be used for routing
B. routes the packet through the tunnel
C. identifies the PIM-SM RP used to route the packet
D. can authenticate VPN endpoints
E. It requires each tunnel endpoint to have an unique network ID
Answer: A, D

Q. What command allows permit or deny IPv6 traffic? (they edited it)
A. traffic-filter access-list-name
B. access-list
C. …
D. access-group
Answer: I was decided to go with answer 'ipv6 access-list' but there was only option 'access-list' without ipv6
I chose A

Q.Which two statements about IP access-lists are true? (Choose two)
A. IP access-lists without at least one deny statement permit all traffic by default.
B. Extended access-lists must include port numbers.
C. They support wildcard masks to limit the address bits to which entries are applies.
D. Entries are applied to traffic in the order in which they appear.
E. They end with an implicit permit.
Answer: C D

Q.What is the minimum log level for the event generated when an ACL drops a packet?
A. 4
B. 5
C. 3
D. 7
E. 6
Answer: E

Q.Which command instruct a PPPoE client to obtain its IP address from the PPPoE server?
A. interface dialer
B. ip address negotiated
C. ip address auto negotiated
D. ip address dhcp
E. pppoe enable
Answer: B

Q.What configurations does PPPoE allow? (Choose two)
A. Client can be installed on the same network devices as server
B. 8 clients can be configured on 1 CPE
C. Clients can connect to multiple hosts over DMVPN
D. Client connecting over ATM PVC
E. Client installed on native IPv6 network
Answer: B C

Q.Which of these can be used for IPv4 to IPv6 communication?(choose two)
A. NAT-PT
B. ISATAP
C. …(something with VPN)
D. …(MPLS maybe)
Answer: A,B

Q.Which option is a prerequisite for stateful NAT64?
A. IPsec for IPv6
B. DNS64
C. Application Level Gateway
D. ICMP64
Answer: B

Q.How can you mitigate fragmentation issues between endpoints separated by a GRE tunnel?
A. PMTU (without “D”)
B. TCP MSS
C. windowing
D. ICMP DF bit
Answer: B

Q.Which of the following is true?
show ntp associations
~172.31.32.2 172.31.32.1 5 29 1024 377 4.2 -8.59 1.6
+~192.168.13.33 192.168.1.111 3 69 128 377 4.1 3.48 2.3
#~192.168.13.57 192.168.1.111 3 32 128 377 7.9 11.18 3.6
* master (synced), # master (unsynced), + selected, – candidate, ~ configured
A. Master is syncing and exchanging NTP packets successfully
B. Master is not syncing but exchanging NTP packets successfully
C. Master is not syncing and not exchanging NTP packets
Answer: B

Q.redistribution from eigrp to ospf (choose two correct)
router eigrp 1
redistribute ospf 100
network 10.10.10.0 0.0.0.255
auto-summary
!
router ospf 100
network 172.16.0.0 0.0.255.255 area 10
redistribute eigrp 1
!
A.will redistribute only clasfull routes
B.routes will be redistributed as E2
C.routes will be redistributed as N2
D. …
E. …
Answer: A (missing 'subnets' in the command), B (default E2)

Q.NTP Stratum (choose two correct)
A. highest valid NTP stratrum level is 16
B. stratrum 1 – directly connect to authoritative server
C. stratrum 0 – directly connect to authoritative server
D. stratrum 15 – invalid ntp
E. Stratrum 2 – receives its time through NTP from a stratum 1 time server
Answer: B E

Q. DMVPN spoke-to-spoke choose one – phase 2, choose two – phase 2 and phase 3
Q. DMVPN spoke-to-spoke choose two – phase 2 and phase 3

That's all what I remember
Since now I'm out. Good luck, wish the best and thanks :)

Thanks Timmy666 for sharing your details with us :o)

Q.What two authentication methods do EIGRP use? (Choose two)
A. TKIP
B. MD5
C. WPA
D. Plain Text
Answer: B D
Q. Which two of the following options are true about NetFlowv9? (Choose two)
A. IEEE standard
B. IETF standard
C. ingress only
D. egress only
E. ingress/egress
Answer: B, E
Q. Question mentioned recently about how to prefer the route 51.51.51.51 over another EIGRP route
Answer: distance 89 51.51.51.51 0.0.0.0
Q. How to set up IP SLA to monitor jitter between the certain limits? <= (it’s jitter now, not bandwidth)
A. Timeout (not timer)
B. Frequency
C. Threshold
D. Queue-limit
Answer: C
Q.Which cisco Express Forwarding component(s) contain forwarding information? (forwarding information, they changed it)
A. FIB, adjacency table (this option was not in the exam)
B. adjacency table.
C. FIB, RIB , Adjanceny table
D. FIB
E. RIB
My Answer is: I would go with 'FIB, adjacency' but that choice was not included in the exam.
I chose B.
Q.What is the NHRP role in DMVPN? (Choose 2)
A. obtains the next-hop to be used for routing
B. routes the packet through the tunnel
C. identifies the PIM-SM RP used to route the packet
D. can authenticate VPN endpoints
E. It requires each tunnel endpoint to have an unique network ID
Answer: A, D
Q. What command allows permit or deny IPv6 traffic? (they edited it)
A. traffic-filter access-list-name
B. access-list
C. …
D. access-group
Answer: I was decided to go with answer 'ipv6 access-list' but there was only option 'access-list' without ipv6
I chose A
Q.Which two statements about IP access-lists are true? (Choose two)
A. IP access-lists without at least one deny statement permit all traffic by default.
B. Extended access-lists must include port numbers.
C. They support wildcard masks to limit the address bits to which entries are applies.
D. Entries are applied to traffic in the order in which they appear.
E. They end with an implicit permit.
Answer: C D
Q.What is the minimum log level for the event generated when an ACL drops a packet?
A. 4
B. 5
C. 3
D. 7
E. 6
Answer: E
Q.Which command instruct a PPPoE client to obtain its IP address from the PPPoE server?
A. interface dialer
B. ip address negotiated
C. ip address auto negotiated
D. ip address dhcp
E. pppoe enable
Answer: B
Q.What configurations does PPPoE allow? (Choose two)
A. Client can be installed on the same network devices as server
B. 8 clients can be configured on 1 CPE
C. Clients can connect to multiple hosts over DMVPN
D. Client connecting over ATM PVC
E. Client installed on native IPv6 network
Answer: B C
Q.Which of these can be used for IPv4 to IPv6 communication?(choose two)
A. NAT-PT
B. ISATAP
C. …(something with VPN)
D. …(MPLS maybe)
Answer: A,B
Q.Which option is a prerequisite for stateful NAT64?
A. IPsec for IPv6
B. DNS64
C. Application Level Gateway
D. ICMP64
Answer: B
Q.How can you mitigate fragmentation issues between endpoints separated by a GRE tunnel?
A. PMTU (without “D”)
B. TCP MSS
C. windowing
D. ICMP DF bit
Answer: B
Q.Which of the following is true?
show ntp associations
~172.31.32.2 172.31.32.1 5 29 1024 377 4.2 -8.59 1.6
+~192.168.13.33 192.168.1.111 3 69 128 377 4.1 3.48 2.3
#~192.168.13.57 192.168.1.111 3 32 128 377 7.9 11.18 3.6
* master (synced), # master (unsynced), + selected, – candidate, ~ configured
A. Master is syncing and exchanging NTP packets successfully
B. Master is not syncing but exchanging NTP packets successfully
C. Master is not syncing and not exchanging NTP packets
Answer: B
Q.redistribution from eigrp to ospf (choose two correct)
router eigrp 1
redistribute ospf 100
network 10.10.10.0 0.0.0.255
auto-summary
!
router ospf 100
network 172.16.0.0 0.0.255.255 area 10
redistribute eigrp 1
!
A.will redistribute only clasfull routes
B.routes will be redistributed as E2
C.routes will be redistributed as N2
D. …
E. …
Answer: A (missing 'subnets' in the command), B (default E2)
Q.NTP Stratum (choose two correct)
A. highest valid NTP stratrum level is 16
B. stratrum 1 – directly connect to authoritative server
C. stratrum 0 – directly connect to authoritative server
D. stratrum 15 – invalid ntp
E. Stratrum 2 – receives its time through NTP from a stratum 1 time server
Answer: B E

Sorry i have problems to share documents…

QUESTION 73
which fuctionality is requierd within an IP router that is situated at the boundary of an IPv4 networks and IPV6 networks to allow communication betwon IPv6-only and Ipv4-only nodes?
A. Autoconfiguration
B. automatic 6to4 tunnel
C. automatic 6to 4 relay
D. networks address translator – protocol (NAT-PT)
E. intrasite automatinc Tunnel address protocol
Correct Answer: B

I think the right answer is D, because tunnels are about discontiguous IPv6 networks with IPv4 in the middle, can someone correct me??