Share your ROUTE v2.0 Experience
| Note: The last day to take this ROUTE 300-101 exam is February 23, 2020. After this day you have to take new Enterprise exams to get new CCNP Enterprise certification. If you want to find out more about the new exams please visit here. |
The ROUTE 300-101 (ROUTE v2.0) exam has been used to replace the old ROUTE 642-902 exam so this article is devoted for candidates who took this exam sharing their experience.
Please tell with us what are your materials, the way you learned, your feeling and experience after taking the ROUTE v2.0 exam… But please DO NOT share any information about the detail of the exam or your personal information, your score, exam date and location, your email…
Note: Posting email is not allowed in the comment section.
Your posts are warmly welcome!
@Tomcat, @BlueH, thank you!
Other than a working EIGRP configuration, which option must be the same on all routers for EIGRP authentication key rollover to work correctly?
A, SNMP
B, Time
C, Passwords
D, SMTP
B or D? What do you think?
Well there no such a thing, just search box and then the title and list of topics Lab Sim…
Top right side of the site
@Dareezy
https://www.digitaltut.com/member/login
Q blach
C is correct
@Tomcat Thanks :)
passwords? EIGRP is not using passwords
@Anonymous
your are right no password in EIGRP
but in this question no key chain in answers, so password might be only correct
https://www.cisco.com/c/en/us/support/docs/ip/enhanced-interior-gateway-routing-protocol-eigrp/82110-eigrp-authentication.html
Guys, what is the current consensus? Are any of the dumps valid, or has CISCO changed the exam to the point where this is a waste of time?
I see folks mention the “Dexter” and “Chinese” dumps? Can anyone comment on the validity?
@blach
Imo correct answer time
@Tomcat
This question has baffled me for some time. In the Cisco link you posted about EIGRP Authentication, it states just 2 requirements…
Requirements:
– The time must be properly configured on all routers. Refer to Configuring NTP for more information.
– A working EIGRP configuration is recommended.
The question specificially says “other than a working configuration”, so I only see one other option and that is “time”. So, would the answer not be B? Thoughts?
@Tomcat @ Dareezy
B Time is correct answer. IF you are doing rollover time must be synced (NTP or manual) otherwise one router can start using new key and other can be using old one and neighbour relation will be torn. Key words in this question are “EIGRP authentication key rollover to work correctly”.
@JBalvin
Almost of the inputs are the same I share here, i think they just compiled that.
When use NPTv6 for IPV6 to IPV6 Address translation? (Choose two)
A. stateful address translation
B. a limit of 32 1-to-1 translations
C. lack of overloading functionality
D. identify all interface NAT inside or outside
E. one-to-one prefix rewrite
F. mismatched prefix allocations
Is the Correct Answer: CE or CF ?!
@weee
Thanks
@Tomcat
np
QUESTION 1
Which statement about stateless and stateful IPv6 autoconfiguration are true?
A. Both stateless and stateful autoconfiguration require additional setup
B. Stateless autoconfiguration requires no additional setup, whereas stateful autoconfiguration requires additional setup
C. Stateless autoconfiguration requires additional setup, whereas stateful autoconfiguration requires no additional setup
D. Both stateless and stateful autoconfiguration require no additional setup
Correct Answer: A or B ?
Hi Guys is worth be coming a premium member for digitaltut, or are the questions out of date?
@alexa
A. stateful address translation
B. a limit of 32 1-to-1 translations
C. lack of overloading functionality
D. identify all interface NAT inside or outside
E. one-to-one prefix rewrite
F. mismatched prefix allocations
My Answer: C E
Which statement about stateless and stateful IPv6 autoconfiguration are true?
A. Both stateless and stateful autoconfiguration require additional setup
B. Stateless autoconfiguration requires no additional setup, whereas stateful autoconfiguration requires additional setup
C. Stateless autoconfiguration requires additional setup, whereas stateful autoconfiguration requires no additional setup
D. Both stateless and stateful autoconfiguration require no additional setup
My answer: A
@Syn less than 50% of the questions are new. If you only study DEXTER and EON and DIGITUT, you are only secure with 50~60% score.
@CCNP fail fail fail,
Thanks for the reply.
@alexa
Which statement about stateless and stateful IPv6 autoconfiguration are true?
A. Both stateless and stateful autoconfiguration require additional setup
B. Stateless autoconfiguration requires no additional setup, whereas stateful autoconfiguration requires additional setup
C. Stateless autoconfiguration requires additional setup, whereas stateful autoconfiguration requires no additional setup
D. Both stateless and stateful autoconfiguration require no additional setup
My answer: B
1.Doesn’t require support of a DHCP server – Stateless Auto Configuration does away with the need of a DHCP server to allocate IP addresses to the individual nodes connected to the Local Area Network (LAN).
2. Allows hot plugging of network devices – The network devices can be ‘hot-plugged’ to the Internet. Since the devices can configure their own IP addresses, there is no need for manual configuration of the network devices. The devices can be simply connected to the network and they automatically configure themselves to be used over an IPv6 network.
@Alexa
The answer is (C)
And (B) is definitely wrong !
refers to:
https://supportforums.cisco.com/t5/network-infrastructure-documents/dynamic-address-assignment-in-ipv6-using-slaac-and-dhcp/ta-p/3109128
@Alexa
SLAAC does not provide anything to the client outside of an IPv6 address and a default gateway.
(Additional configuration on the server is necessary) before the same information can be provided
to the client as Stateful DHCP.
https://supportforums.cisco.com/t5/network-infrastructure-documents/dynamic-address-assignment-in-ipv6-using-slaac-and-dhcp/ta-p/3109128
@ISAKAMP and confuse guy
Which statement about stateless and stateful IPv6 autoconfiguration are true?
A. Both stateless and stateful autoconfiguration require additional setup
B. Stateless autoconfiguration requires no additional setup, whereas stateful autoconfiguration requires additional setup
C. Stateless autoconfiguration requires additional setup, whereas stateful autoconfiguration requires no additional setup
D. Both stateless and stateful autoconfiguration require no additional setup
Answer: A is correct as in Dexter Dump
I will take exam in tomorrow 9:00 in Thailand . I’m Jedi, “May the Force be with you”
I study EON,New-Doko,DEXTER,Chinise,Korea,and New Q in this page TUT
We Fight! We Fight! Arrrr hoo! Arrr hoo!
@ISAKAMP
Did you finish to read the same paragraph you mentioned as reference because they also say below:
Additional configuration on the server is necessary before the same information can be provided to the client as Stateful DHCP.
Hi you can this web site. it’s free http://chen-academy.com/edukn/certificates/ccnp-route-300-101/
FirePOWDER
Good luck
I’ve got exam in 2 week please update us
which two protocol are required for DMVPN?(choose two)
PPTP
IPSed
mGRE
NHRP
Open VPN
Ans. mGRE & NHRP
Explanation:
DMVPN combines multiple GRE (mGRE) Tunnels, IPSec encryption and NHRP (Next Hop Resolution Protocol) to perform its job and save the administrator the need to define multiple static crypto maps and dynamic discovery of tunnel endpoints.
Note:
DMVPN is not a protocol, it is the combination of the following technologies:
+ Multipoint GRE (mGRE)
+ Next-Hop Resolution Protocol (NHRP)
+ Dynamic Routing Protocol (EIGRP, RIP, OSPF, BGP…) (optional)
+ Dynamic IPsec encryption (optional)
+ Cisco Express Forwarding (CEF)
@trytohelp
nice website. thanks
Another I believe wrong answe for the question within all dumps:
Which BGP option is required when load sharing over multiple equal-bandwidth parallel links from a single CE router to a single ISP router over eBGP?
A. eBGP Multipath
B. eBGP Multihop
C. BGP Synchronization
D. Public AS numbers
All dumps says that correct is B, but eBGP Multihop option is used when your BGP neighbor is not in directly connected network with you.
I think that correct option here is eBGP Multipath, because this term cisco used in references:
https://www.cisco.com/c/en/us/td/docs/ios/12_2sx/feature/guide/fsxeibmp.html#wp1049023
Read China Dumps, somehow different:
which three configuration parameters can a DHCPV6 pool contain? (choose three.)
A. domain search list
B. router IP
C. default gateway
D. prefix delegation
E. DNS servers
F. subnet mask
Correct Answer: DEF?
which type of access list allows granular session filtering for upper-level protocols?
A. content-based access lists
B. context-based access lists
C. reglexive access lists
D. extended access lists
Correct Answer: D?
The enterprise network WAN link has been received several denial of service attacksfrom both IPv4 and
IPv6 sources. Which three elements can you use to identify an IPv6 packet via its header, in order to filter
future attacks?(Choose three)
A. Traffic Class
B. Source address
C. Flow Label
D. Hop Limit
E. Destination Address
F. Fragment Offset
Correct Answer: ACD?
Other than a working EIGRP configuration, which option must be the same on allrouters for EIGRP
authentication key rollover to work correctly?
A. SMTP
B. SNMP
C. Passwords
D. Time
Correct Answer: D?
What is the minimum log level for the event generated when an ACL drops a packet?
A. 3
B. 4
C. 5
D. 6
E. 7
Correct Answer: E?
Question
The enterprise network WAN link has been received several denial of service attacks from both IPv4 and IPv6 sources. Which three elements can you use to identify an IPv6 packet via its header, in order to filter future attacks?(Choose three)
I think the correct answer is (Source address, Destination Address, Flow Label)
anyone confirm please
@CCNP fail fail fail
1. A,D,E. I checked it in gns ipv6 dhcp pool configuration. It cannot be a subnet mask because ipv6 only have prefixes.
2. D.
3. I think it must be A, B and C. Not 100% confident about it, but this how you can identify traffic flow to block it in the future.
4. D, but not sure.
5. E, in general you only can see ACL drops a packet in a debug mode, which severity level is 7.
@Anonymous IMO it rather Source address, Destination Address and Traffic Class. You cannot use flow label in the future, cause it is kinda hash and it changes from one time to another.
Question:
To enable BGP tunneling over an IPv4 backbone, the IPv4 address 192.168.30.1 is converted into a valid IPv6 address.
Which three IPv6 addresses are acceptable formats for the IPv4 address? (Choose three.)
A. 192.168.30.1:0:0:0:0:0:0
B. 0:0:0:0:0:0:192.168.30.1
C. ::192.168.30.1
D. C0A8:1E01::
E. 192.168.30.1::
F. ::C0A8:1E01
Correct Answer: BCF?
Which answers are correct? It can be C and F, but in there is too many hextets in B. I confused.
@CCNP fail it you have in question about acl upperr-level protocol reflexive access list this is correct
Pass the exam today.
my advise for you go through all new questions shared.
DEXTER is good one read it and understand the concept not the answer.
you should be ok.
Regards.
Q.Which type of access list allows granular session filtering for upper-level protocols?
A. content-based access lists
B. context-based access lists
C. reglexive access lists
D. extended access lists
Q.Which type of access list allows granular session filtering for upper-level protocols?
A. content-based access lists
B. context-based access lists
C. reflexive access lists
D. extended access lists
Please let me know right answer ( C or D) ?
2018 latest ccna dumps
look my name
@Xenlay
Q.Which type of access list allows granular session filtering for upper-level protocols?
C
If you should not find the answer “Reflexive” you have to choose “Extended”
Reflexive access lists (see the section “Types of IP Access Lists” and the module “Configuring IP Session Filtering [Reflexive Access Lists])
Reflexive Access Lists
Reflexive access lists provide filtering on upper-layer IP protocol sessions. …
https://www.cisco.com/en/US/docs/ios-xml/ios/sec_data_acl/configuration/15-1s/sec-access-list-ov.html
@Natan
0:0:0:0:0:0:(This Part is 96 bit) – 192.168.30.1[Decimal]=C0A8:1E01[Hex] is the remaining 32Bit
@EIGRP Stub, already got it. Thanks for explaining:-)
@EIGRP Stub
Thank you for your explanation.
Question
which value does GRE Tunnel use to identify the end points or destination ?
The correct answer IP address or Tunnel ?
Q: logging console 7. Which is true ?
A. you can see debug if you’re connected in SSH
B. High CPU utilization
C. …
what is the answer???
Q:Where to configure the DHCPv6 relay IP address for a VLAN
Do you have to enable DHCPv6 relay in the global configuration mode/VLAN interface ?
Do you have to configure something on the VLAN interface/global configuration
???
Q:where to apply ipv6 traffic filter ? (they actually show you possible configuration commands, in interface, global … modes).
A. interface configuration
B. router configuration
C. global configuration
???
I did the exam today but failed :(
There were a lot of new questions I never seen before round about 15 Questions were visible from the china, Dexter and EON
DnD
DHCP >there was a new one<
Authentication-Authorization-Accounting
mGRE – IPsec – MSS – Tunnel key – keepalive
LMI
PBR SIM
EIGRP SIM
EIGRP Evaluation Sim
1.What would you configure on snmpv3 to allow encryption ?
Choose : Authpriv
2. New Hop and spoke Topologie
3.Which two configurations can a PPPoE Client Support ?
Answer was…
Eight Clients…
4.Which two statements about IP access-list is true ?
They support wildcard mask.
… which they appear.
5.Which cisco Express Forwarding components contain forwarding information ?
FIB, adjaceny table
6.What are two protocols used for user with authentication network device ?
Radius
Tacacs+
7.Which three IP SLA performance metricscan you use to monitor enterprise-class networks ?
Packet loss
Delay
Connectivity
8.Which command enables NAT-PT on an IPv6 interface ?
Ipv6 nat
9.Which two functionalities are specific to stateful NAT64 ?
10.Refer to the exhibit. Which effect of this configuration is true ?
….. picute with confi shows …..ntp master 10
Answwer : R1 acts as an auth closck at stratum 10.
11. There was a question with a config example and in the end we had …..Snmp 16
Question was what does the 16 cause in this example ?!
12.Question with config example : sh ip route vrf purple
it shows the routing table for vrf purple
13.A Network Engineer has set up VRF-Lite on two Routers…
Answer :
adding a static Routefor the vrf that points to the global torute table
and
adding the loopback to the VRF
14.DHCEPv6 can optain configuration parameters from server through rapid two-way message exchange.
Solicit
reply
15.Which three options are valid DHCPv6 functions ?
Server
Client
Relay
16.Which three problems result from application mixing of UDP and TCP streams within a network with no QOS ?
Starvation
Jitter
Latency
17.Which two protocols can cause TCP starvation ?
TFTP
SNMP
18.Frame Relay LMI autosense.
Line should be up and protocol should be down
it only works onDTEs
– they were question about uRPF (I gues 2 Questions)
– question about enable or disable split horizon but different to our examples listed in Dexter or China Dump
– question about “loose mode“ , other as we know !
– quesion what will “any” in the statement mean… other question as we know
– all other Q&A were new and not present in the Dumps
@ll : in the PBR LAB there is a TEST PC which create traffic (I guess 9 packets or something)… This windows shows ********* ….should it be correct ?! Where can I see this creating packets , because some commands are not allowed …or should i see in the output !!!!!!!!! …. so that mean I did something wrong.
@next_try these questions are new? I have observed some these question on the dump.