Share your ROUTE v2.0 Experience

first, what is frame Relay config its is lab or DnD?

IPv6 has just been deployed to all of the hosts within a network. but not to the server. which feature allows iPv6 device to communicate wih ipv4 server?
A. NAT64
B.DNS64

is A or B?

NM, its NAT64.

@Dareezy, thanks!

QUESTION 54
Other than a working EIGRP configuration, which option must be the same on all routers for EIGRP
authentication key rolleover to work correctly?
A. SMTP
B. SNMP
C. Passwords
D. Time
Correct Answer: C , D ?????????
what is correct ??

Cisco questions are so f… stupid

The key chain name is only locally significant but the key number and key string must match on neihgboring routers. So answer is probably C. IF question is formulated other way must pay attention

Hello my friend took the exam yesterday and passed. He informed me that he only saw 2 -3 new questions apart from the Dokdo/EON dumps. Are we sure there is an update? Are people using the dokdo and EON dump to study for the exam?

Is the Dokdo dump and Dexter Dump the same thing?

No it is not. It has 79Q which was used to use on top of other dumps. It may have some same questions but should have new questions that are not in the dexter dumps.

Oh. Thanks! Do you happen to have a link? If not I can look back through the pages and try to find one.

Here is a link to the dokdo dump. See that you are taking the exam tomorrow. Study this dump as well and if you can give us feedback tomorrow in regards to validity of the dumps.

https://www.dropbox.com/s/n47fsn7aq734rz0/%5B300-101%5D%20Dokdo%20dump.pdf?dl=0

QUESTION 3
What is the minimum level that displays a log message when an ACL drops an incoming packet?
A. 4
B. 5
C. 3
D. 7
E. 6
Correct Answer: E or D ????
what correct answer

Which value does GRE tunnel use to identify the end points or destination
A. IP ADDRESS
B. MAC ADDRESS
C. DLCI
D. TUNNEL
Correct Answer: A or C ?????
what correct answer???

QUESTION 50
What from the following can cause an issue for URPF?(this could be single answer
or multiple choice)
A.Assymetric routing
B.Cef not enabled
C.Urpf not applied to the traffic source
D.If it is used as ingress filtering
Answer: A or C ??????
what is correct answer?????

Thanks It there an update?…….I can’t open dropbox at work. You mind emailing or if you have another link or something? Seahwk1218 at gmail.com

Of I’ll be providing feedback after I test tomorrow. Will answer any questions.

Gre uses ip addres.

QUESTION 92
When use NPTv6 for IPV6 to IPV6 Address translation? (Choose two)
A. stateful address translation
B. a limit of 32 1-to-1 translations
C. lack of overloading functionality
D. identify all interface NAT inside or outside
E. one-to-one prefix rewrite
F. mismatched prefix allocations
Correct Answer: CE or CF ?????????? what is answer

Hey guys you are asking the same basic questions again and again. you need to study hard. if you pay here you will find some questions that engineers that took the exam mention as a new questions.

the only new dumps are the chinesse and those are not all the questions.
I will share new questions and I expect some body can clear if the questions that I have were presented in the exam.

Question 1

What are three of Frame Relay LMI extensions? (Choose three)

A. Global addressing
B. Virtual circuit status messages
C. Multicasting

Answer: A B C

Question 2

Question about IP SLA deployment cycle. Chose best IP SLA deployment cycle that reduce deployment.

Answer: baseline (network performance), understand (network performance baseline), fine tune and optimize, quantify (results)

Reference: https://www.cisco.com/en/US/technologies/tk648/tk362/tk920/technologies_white_paper0900aecd8017f8c9.html

Question 3

Question about IPv6 EIGRP features

Answer: scaling and updates partials

Question 4

Question about PADO, PADR and PADI definition

Answer:

+ PPPoE Active Discovery Initiation (PADI): The client initiates a session by broadcasting a PADI packet to the LAN to request a service.
+ PPPoE Active Discovery Offer (PADO): Any access concentrator that can provide the service requested by the client in the PADI packet replies with a PADO packet that contains its own name, the unicast address of the client, and the service requested. An access concentrator can also use the PADO packet to offer other services to the client.
+ PPPoE Active Discovery Request (PADR): From the PADOs it receives, the client selects one access concentrator based on its name or the services offered and sends it a PADR packet to indicate the service or services needed.

Question 5

Question about NTP Authentication, NTP trusted key authorises the entity, NTP Authentication Key ID enables NTP on the interface

Question 6

Which two of the following options are true about NetFlowv9? (Choose two)

A. IEEE standard
B. IETF standard
C. ingress only
D. egress only
E. ingress/egress

Answer: B E

Question 7

Which security level is supported throughout all SNMP versions?

A. authPriv
B. authNoPriv
C. noAuthNoPriv

Answer: C

Question 8

One long question something like router get IPv6 information from ISP. Now it have to distribute name server and other options to hosts (how do routers distribute prefixes obtained from
ISPs using DHCPv6)

A. PPPv6
B. DHCP
C. Stateful Natv6
D. NPTv6
E. IPv4

Answer: Stateful NATv6

Question 9

Which of the following SNMPv2 uses for authentication?

A. HMAC-MD5
B. HMAC-SHA
C. CBC-DES
D. Community strings

Answer: D

Question 10

Drag drop about DMVPN components.

Answer:

Hub – …. next-hop server
Spoke – … device …. dynamic address
mGRE – … multi tunnel endpoint …
NHRP – … protocol …

Please read our DMVPN tutorial to grasp these components.

Question 11

Which are two methods for migrating routing protocols?

A. Changing AD Distance
B. Redistribution
C. ACL

Answer: A B

Question 12

A diagram with 3 routers:
+ H1 (with IPv6 IP and Loopback 1.1.1.1)
+ R1 (with IP IPv6 and Loopback 2.2.2.2)
+ R2 (with IP IPv6 and Loopback 3.3.3.3)

running with EIGRP 100 on both routers and what command you will implement so that you will see the loopback IP of R2 to be advertised at H1

A. H1(config t)#router eigrp 100
H1(config t)#no stub only
B. R2(config t)#router eigrp 100
R2(config t)#no stub receive only
C. H1(config t)#ipv6 router eigrp 100
H1(config t)#no stub only
D. R2(config t)#ipv6 router eigrp 100
R2(config t)#no stub only

Answer: B (no stub receive-only)

Question 13

Which two statements about NHRP in a DMVPN environment are true? (Choose two)

A. It requires each endpoint to have a unique network ID
B. It routes traffic through the tunnel
C. It can identify PIM-SM RPs over a tunnel
D. It can authenticate VPN endpoints
E. It provides address resolution to route traffic

Answer: D E

Question 14

Drag drop question about LMI

+ Address registration – allows neighboring Cisco devices to exchange the management ip addresses
+ Global addressing – Enables Frame Relay to identify interfaces in same manner as LAN
+ Multicasting – Provides most efficient transmission of routing protocol messages and support address resolution
+ Simple flow control – Supports devices that are unable to use congestion notification
+ Virtual circuit – Prevents data from being transmitted in black hole

Question 15

Which two commands do you need to implement on the CALLING router to support the PPPoE client? (choose two)

A. peer default ip address pool
B. mtu
C. bba-group pppoe
D. pppoe enable group
E. pppoe-client dialer-pool-number

Answer: B E

Question 16

Which option to the command service timestamps debug enables the logging server to capture the greatest amount of information from the router?

A. uptime
B. show-timezone
C. year
D. msec

Answer: D

Question 17

choose correct statement about Dynamic NAT.

Answer: inside local, this list will be translated to this subnet (which is pool)

Question 18

Which value does GRE tunnel use to identify the end points or destination?

A. IP address
B. MAC address
C. DLCI

Answer: A

Explanation

For Frame Relay the answer would be DLCI but here it is asking about GRE tunnel so the best choice here is “IP address”.

Question 19

A topology with eigrp, a hub and two spokes, where the loopback of the spokes are not seeing each others.

Answer: Disable split horizon on the hub

Question 20

If you run the command auto-cost reference-bandwidth 10000 on one of the router in the network, what will happen?

A. It will make 10Gbps on all of them
B. It will make 1 Gbps on all of them
C. It will make 10Gbps on this router only

Answer: C

Explanation

This command affects all the OSPF costs on the local router as all links are recalculated with formula: cost = reference-bandwidth (in Mbps) / interface bandwidth

Therefore in this case the command “auto-cost reference-bandwidth 10000” allows the local router to calculate the link up to 10Gbps.

Question 21

Question with network topology, it is OSPF network is redistributing RIP. Question is how to summarize those route.

Answer: Summary-address (not sure)

Question 22

What algorithm is used in EIGRP?

Answer: DUAL

Question 23

Which two protocols are used to deploy a single Hub-DMVPN supporting Spoke-to Spoke tunnels? (Choose two)

A. MPLS
B. RSVP
C. NHRP
D. BFB
E. Multipoint GRE

Answer: C E

Can somebody confirm if the last questions were in the exam.?

Guys, every exam is different. There is a basic pool of questions that the test pulls answers from. Just because one test may have a question, doesn’t mean the next test will. Study the concepts. Use the dumps for reinforcement.

any one have dokodo dumps

SW, the 79Q Dodko dump?

I have them on my laptop

Question 1

What are three of Frame Relay LMI extensions? (Choose three)

A. Global addressing
B. Virtual circuit status messages
C. Multicasting

Answer: A B C

Question 2

Question about IP SLA deployment cycle. Chose best IP SLA deployment cycle that reduce deployment.

Answer: baseline (network performance), understand (network performance baseline), fine tune and optimize, quantify (results)

Reference: https://www.cisco.com/en/US/technologies/tk648/tk362/tk920/technologies_white_paper0900aecd8017f8c9.html

Question 3

Question about IPv6 EIGRP features

Answer: scaling and updates partials

Question 4

Question about PADO, PADR and PADI definition

Answer:

+ PPPoE Active Discovery Initiation (PADI): The client initiates a session by broadcasting a PADI packet to the LAN to request a service.
+ PPPoE Active Discovery Offer (PADO): Any access concentrator that can provide the service requested by the client in the PADI packet replies with a PADO packet that contains its own name, the unicast address of the client, and the service requested. An access concentrator can also use the PADO packet to offer other services to the client.
+ PPPoE Active Discovery Request (PADR): From the PADOs it receives, the client selects one access concentrator based on its name or the services offered and sends it a PADR packet to indicate the service or services needed.

Question 5

Question about NTP Authentication, NTP trusted key authorises the entity, NTP Authentication Key ID enables NTP on the interface

Question 6

Which two of the following options are true about NetFlowv9? (Choose two)

A. IEEE standard
B. IETF standard
C. ingress only
D. egress only
E. ingress/egress

Answer: B E

Question 7

Which security level is supported throughout all SNMP versions?

A. authPriv
B. authNoPriv
C. noAuthNoPriv

Answer: C

Question 8

One long question something like router get IPv6 information from ISP. Now it have to distribute name server and other options to hosts (how do routers distribute prefixes obtained from
ISPs using DHCPv6)

A. PPPv6
B. DHCP
C. Stateful Natv6
D. NPTv6
E. IPv4

Answer: Stateful NATv6

Question 9

Which of the following SNMPv2 uses for authentication?

A. HMAC-MD5
B. HMAC-SHA
C. CBC-DES
D. Community strings

Answer: D

Question 10

Drag drop about DMVPN components.

Answer:

Hub – …. next-hop server
Spoke – … device …. dynamic address
mGRE – … multi tunnel endpoint …
NHRP – … protocol …

Please read our DMVPN tutorial to grasp these components.

Question 11

Which are two methods for migrating routing protocols?

A. Changing AD Distance
B. Redistribution
C. ACL

Answer: A B

Question 12

A diagram with 3 routers:
+ H1 (with IPv6 IP and Loopback 1.1.1.1)
+ R1 (with IP IPv6 and Loopback 2.2.2.2)
+ R2 (with IP IPv6 and Loopback 3.3.3.3)

running with EIGRP 100 on both routers and what command you will implement so that you will see the loopback IP of R2 to be advertised at H1

A. H1(config t)#router eigrp 100
H1(config t)#no stub only
B. R2(config t)#router eigrp 100
R2(config t)#no stub receive only
C. H1(config t)#ipv6 router eigrp 100
H1(config t)#no stub only
D. R2(config t)#ipv6 router eigrp 100
R2(config t)#no stub only

Answer: B (no stub receive-only)

Question 13

Which two statements about NHRP in a DMVPN environment are true? (Choose two)

A. It requires each endpoint to have a unique network ID
B. It routes traffic through the tunnel
C. It can identify PIM-SM RPs over a tunnel
D. It can authenticate VPN endpoints
E. It provides address resolution to route traffic

Answer: D E

Question 14

Drag drop question about LMI

+ Address registration – allows neighboring Cisco devices to exchange the management ip addresses
+ Global addressing – Enables Frame Relay to identify interfaces in same manner as LAN
+ Multicasting – Provides most efficient transmission of routing protocol messages and support address resolution
+ Simple flow control – Supports devices that are unable to use congestion notification
+ Virtual circuit – Prevents data from being transmitted in black hole

Question 15

Which two commands do you need to implement on the CALLING router to support the PPPoE client? (choose two)

A. peer default ip address pool
B. mtu
C. bba-group pppoe
D. pppoe enable group
E. pppoe-client dialer-pool-number

Answer: B E

Question 16

Which option to the command service timestamps debug enables the logging server to capture the greatest amount of information from the router?

A. uptime
B. show-timezone
C. year
D. msec

Answer: D

Question 17

choose correct statement about Dynamic NAT.

Answer: inside local, this list will be translated to this subnet (which is pool)

Question 18

Which value does GRE tunnel use to identify the end points or destination?

A. IP address
B. MAC address
C. DLCI

Answer: A

Explanation

For Frame Relay the answer would be DLCI but here it is asking about GRE tunnel so the best choice here is “IP address”.

Question 19

A topology with eigrp, a hub and two spokes, where the loopback of the spokes are not seeing each others.

Answer: Disable split horizon on the hub

Question 20

If you run the command auto-cost reference-bandwidth 10000 on one of the router in the network, what will happen?

A. It will make 10Gbps on all of them
B. It will make 1 Gbps on all of them
C. It will make 10Gbps on this router only

Answer: C

Explanation

This command affects all the OSPF costs on the local router as all links are recalculated with formula: cost = reference-bandwidth (in Mbps) / interface bandwidth

Therefore in this case the command “auto-cost reference-bandwidth 10000” allows the local router to calculate the link up to 10Gbps.

Question 21

Question with network topology, it is OSPF network is redistributing RIP. Question is how to summarize those route.

Answer: Summary-address (not sure)

Question 22

What algorithm is used in EIGRP?

Answer: DUAL

Question 23

Which two protocols are used to deploy a single Hub-DMVPN supporting Spoke-to Spoke tunnels? (Choose two)

A. MPLS
B. RSVP
C. NHRP
D. BFB
E. Multipoint GRE

Answer: C E

Hi guys, I just passed CCNA yesterday and I was hoping if you have some books and dumps that I can use. for CCNP route thank you very much!

@mosh
Congrats bro and welcome to CCNP club. Browse the previous pages u’ll find different dumbs.

Thanks @khalifa..

@ Anonymous : can you provide me the link or page number with the dodko dump please ?!

@digitaltut : Can you please explain me what the benefit for the premium Member Account is ?!
Do I get other information like pdf or vce dumbs etc. …what is the different ?
Thanks a lot in advance.

Hi all, My name is Anus. May I know what this forum about?

Anus, it’s kind of in the title of the forum.

@Sims, the chinese vce looks promising. thanks for the link.

Pls share chinese link

@Digitaltut

Can you please confirm with premium membership is up to date and relevant to today’s studies?

hi all, I passed yesterday with 8xx

As some have said, most of the exam questions are in the dexter dump but they are written differently. It is also true that there are several new questions that I have not seen before in any dump.

The DHCP Relay DnD is about relating some commands to their purposes. Some of the commands were the following:
ip dhcp relay information option
ip dhcp relay information check
ip dhcp relay information policy
ip dhcp relay information trusted-sources

Hi Guys,
Does any one knows whatapp group for preparing ccnp route exam? If so, could you please provide the link.Thanks.

i took today and failed (get around almost pass score). Too many rephrasing MC question..lab and DnD almost same.
DnD new,

ip dhcp relay information option—- xxx
ip dhcp relay information check—-xxx
ip dhcp relay information policy=xxxx
ip dhcp relay information trusted-sources-xxxx

eigrp stub lab, i see 10.0.0.0/24 is variable subnneted when i did **sh ip route*, dont know shod i use 255.255.0.0 or 255.255.255.0 on summarize. i use 255.255.0.0 SM.

also, one question was like which neighbor protocol will eliminate( replace not sure phrase) ipv6 to ipv4

option is cdp, icmp, mac, etc…

need to find updated DUMPs!!!!

Here is a good link on the DHCP DND above.

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipaddr_dhcp/configuration/15-sy/dhcp-15-sy-book/dhcp-relay-agent.html#GUID-F2F3913C-D710-4377-AC5D-DFF39E165644

@digitaltut why does my previous comment doesn’t appear

@ TakingExamSooner

iR4
int serial0/0
ip summary-address eigrp 123 10.2.0.0 255.255.0.0

R3 Show ip route

Do you remember anything else about the DHCP dnd?

Took today and failed….barely. I would say about 60 % are questions I saw on Dexter Dump and other dumps I’ve seen here. Definitely some new questions.

Labs – EIGRP Stub; OSPF Eval and EIGRP Eval.

Couple of new DnDs.

I’ll try to post what questions I remember if anyone thinks it will help them. Feel free to ask questions.

@ Sco
Whatever you remember helps..

ip dhcp relay information option:
Enables the system to insert the DHCP relay agent information option (option-82 field) in BOOTREQUEST messages forwarded to a DHCP server.

ip dhcp relay information check:
Configures DHCP to check whether the relay agent information option in forwarded BOOTREPLY messages is valid.

ip dhcp relay information policy:
Configures the reforwarding policy (that specifies what a relay agent should do if a message already contains relay information) for a DHCP relay agent.

ip dhcp relay information trusted:
Configures all interfaces on a router as trusted sources of the DHCP relay information option.

When a packet is denied by an IPv6 traffice filter, which additional action does te device perform?
A. It generates a TCP Fin bit and sends it to the source.
B. It scans the rest of the ACL for a permit entry matching the destination.
C. It generates an ICMP unreachable message for the frame.
D. It creates a null route for te destination and adds it to the route table.
Correct Answer: C

In which scenario can asymmetric routing occur?
A. active/active firewall setup
Dexter ITC
B. single path in and out of the network.
C. active/standby firewall setup
D. redundant routers running VRRP
Correct Answer: A

Which technology was originally developed for routers to handle fragmentation in the path between end points?
A. PMTUD
B. MSS
C. windowing
D. TCP
E. global synchronization
Correct Answer: A

Which value does Frame Relay use to identify a connection between a DTE and DCE?
A. DLCI
B. IP address
C. MAC address
D. VLAN ID

Which cisco Express Forwarding component maintains Layer 2 addressing information?
A. dCEF
B. adjacency table.
C. FIB
D. fast switching
E. RIB

What configurations does PPPoE allow? (Choose two)
A. Client can be installed on the same network devices as server
B. 8 clients can be configured on 1 CPE
C. Clients can connect to multiple hosts over DMVPN
D. Client connecting over ATM PVC
E. Client installed on native IPv6 network

In which two ways can split horizon issues be overcome in a Frame Relay network environment? (choose two.)
A. Configuring one physical serial interface with Frame Relay to various remote sites.
B. Configure a loopback interface with Frame Relay to various remote sites
C. Configuring multiple subinterfaces on a single physical interface to various remote sites.
D. Enabling split horizon.
E. Disabling split horizon.

A network engineer enables OSPF on a Frame Relay WAN connection to various remote sites, but no OSPF
adjacencies come up.
Which two actions are possible solutions for this issue? (Choose Two)
A. Change the network type to point-to-multipoint under WAN interface.
B. Enable virtual links.
C. Change the network type to nonbroadcast multipoint access.
D. Configure the neighbor command under OSPF process for each remote site.
E. Ensure that the OSPF process number matches among all remote sites

EIGRP is implemented in a frame relay network but there is no adjacency.
Which options cause the adjacency to come up? (choose 2)
A. disable split horizon
B. neighbor command to configure it for a point to multipoint on the WAN interface

A network engineer is modifying RIPng timer configuration.
Which configuration mode should the engineer use?
A. router(config-rtr)#
B. router(config-ripng)#
C. router(config-if)#
D. router(config)#
Correct Answer: A

During which DMVPN phase is spoke-to-spoke communication enabled?
A. Phase 1
B. Phase 6
C. Phase 5
D. Phase 2
E. Phase 4
Correct Answer: D

After reviewing the EVN configuration, a network administrator notices that a predefined EVN, which is known
as “vnet global” was configured. What is the purpose of this EVN? (OR)
What is the purpose of ‘vnet global”?
A. It defines the routing scope for each particular EVN edge interface.
B. It aggregates and carries all dot1q tagged traffic.
C. It refers to the global routing context and corresponds to the default RIB.
D. It safeguards the virtual network that is preconfigured to avoid mismatched routing instances.
Correct Answer: C

Which authentication methods are EIGRP uses?
A. sha
B. md5
C. xda
D. chap
E. cisco
Correct Answer: B

Refer to the following configuration command.
router(config)# ip nat inside source static tcp 172.16.10.8 8080 172.16.10.8 80
Which statement about the command is true?
A. Any packet that is received in the inside interface with a source IP port address of 172.16.10.8:80 is
translated to 172.16.10.8:8080.
B. Any packet that is received in the inside interface with a source IP port address of 172.16.10.8:8080 is
translated to 172.16.10.8:80.
C. The router accepts only a TCP connection from port 8080 and port 80 on IP address 172.16.10.8
D. Any packet that is received in the inside interface with a source IP address of 172.16.10.8 is redirected to
port 8080 or port 80.
Correct Answer: B

Which statement describes what this command accomplishes when inside and outside interfaces are correctly
identified for NAT?
ip nat inside source static tcp 192.168.1.50 80 209.165.201.1 8080 extendable
A. It allows host 192.168.1.50 to access external websites using TCP port 8080.
B. It allows external clients coming from public IP 209.165.201.1 to connect to a web server at 192.168.1.50.
C. It allows external clients to connect to a web server hosted on 192.168.1.50.
D. It represents an incorrect NAT configuration because it uses standard TCP ports.
Correct Answer: C

What is the purpose of the autonomous-system {autonomous-system-number} command?
A. It sets the EIGRP autonomous system number in a VRF.
B. It sets the BGP autonomous system number in a VRF.
C. It sets the global EIGRP autonomous system number.
D. It sets the global BGP autonomous system number.
Correct Answer: A

How does an EVN provide end-to-end virtualization and separation of data traffic from multiple networks?
A. on the edge interface, with vnet tag
B. on the edge, with 801.q
C. on the trunk, with vnet tag
D. on the trunk, with 802.1 q
Correct Answer: C

Which encapsulation supports an interface that is configured for an EVN trunk?
A. 802.1Q
B. ISL
C. PPP
D. Frame Relay
E. MPLS
F. HDLC
Correct Answer: A

Which two statements about IP access list are true? (Choose two) (I missed this one somehow)
A. They support wildcard masks to limit the address bits to which WAN technologiesed
B. Extended access lists must include port numbers
C. IP access list without at least one deny statement permit all traffic by default
D. They end with an implicit permit
E. Entries are applied to traffic in the order in which they appear
Correct Answer: AE

What is the command to enable IPv6 access list?
(OR)
What command allows permit or deny IPv6 traffic?
A. ipv6 traffic-filter access-list-name { in | out }
B. ipv6 access-list [access-list-name]
C. access-list ipv6 [access-list-name]
D. ipv6 access-group [access-list-name] { in | out }
Correct Answer: A

Which two different configuration can you apply to a device to block incoming SSH access? (Choose two)
A. ipv6 access-list VTY-ACESS-IN
sequence 10 deny tcp any any eq 22
sequence 20 permit ipv6 any any
interface Ethernet0/0
ip traffic-filter VTY-ACCESS-IN out
B. ipv6 access-list VTY-ACESS-IN
sequence 10 deny tcp any any eq 22
sequence 20 permit ipv6 any any
interface Ethernet0/0
ip traffic-filter VTY-ACCESS-IN in
C. ipv6 access-list VTY-ACESS-IN
sequence 10 deny tcp any any eq 22
sequence 20 permit ipv6 any any
line vty 0 15
ip access-class VTY-ACCESS-IN in
D. ipv6 access-list VTY-ACESS-IN
sequence 10 deny tcp any any eq 22
sequence 20 permit ipv6 any any
line vty 0 15
ip access-list VTY-ACCESS-IN out
E. ipv6 access-list VTY-ACESS-IN
sequence 10 deny tcp any any eq 22
sequence 20 permit ipv6 any any
interface Ethernet0/0
ip traffic-filter VTY-ACCESS-IN out
Correct Answer: BC

Features of Netflow version 9?
A. Cisco proprietary
B. IEEE standard
C. IETF
Correct Answer: C

Given ((diagram with R1 SLA config)) with configuration written on Picture as
R(Config)#ip sla 1
R1(Config-ip-sla)#icmp-echo 172.20.20.2 source-interface f1/0
R1(Config-ip-sla)#frequency 10
R1(Config-ip-sla)#threshold 100
R1(Config)#ip sla schedule 1 start-time now life forever
R1(Config)#track 10 ip sla ???-
R1(Config)#ip route 0.0.0.0.0 0.0.0.0 172.20.20.2
What make default route not removed when SLA state down or failed?
A. the destination must be 172.30.30.2 for icmp-echo
B. the threshold value is wrong
C. missing of track feature on default static route command

Which three problems result from application mixing of UDP and TCP streams within a network with no QoS?
(Choose three.) (Wasn’t exactly worded this way)
A. starvation
B. jitter
C. latency
D. windowing
E. lower throughput
Correct Answer: ACE

Drag and Drops:

Cisco Express Forwarding Adjacency Type

Frame Relay component

ACL (One where they describe Extended as being between 1300-1999)

Labs

OSPF Eval (NOTE: The question about the timers…IT WOULD NOT let me type “show ip OSPF interface s1/0”

EIGRP Eval

EIGRP Stub

I had an exhibit with 3 routers. The question asked what should R1 show in routing table if router 3 is configured as an EIGRP Stub or something like that.

I had another one asking about BGP route for network would be selected based on an exhibit of BGP routing table.

I had one asking about Stratum values for a router connected to a master connected to a authoritive clock or something.

I also had a Frame Relay drag and drop where you finish the configuration they show on screen and they block out certain parts.

I’m sorry I don’t remember exact details of these questions. If I can think of anything else I’ll add.

I’m truly kind of surprised I didn’t pass. I mean I barely failed but it is what it is I guess. Feel free to ask away.

Sco … are they questions came to you in your exam ? How many number questions New?

The questions I posted are ones I remember from exam that I’ve seen in a dump (Dexter). As far as new questions, I don’t know the exact number I would probably guess around 15 but that might be a high guess.

I had these too and I’m remembering a couple more I saw somewhere else that I’ll paste shortly.

Could someone please answer these for me?

Router#show ntp associations

address ref clock st when poll reach delay offset disp
~172.31.32.2 172.31.32.1 5 29 1024 377 4.2 -8.59 1.6
+~192.168.13.33 192.168.1.111 4 69 128 377 4.1 3.48 2.3
*~192.168.13.57 192.168.1.111 3 32 128 377 7.9 11.18 3.6
* master (synced), # master (unsynced), + selected, – candidate, ~ configured

Q: Which of the following is true

A. Master is syncing and exchanging NTP packets successfully
B. Master is not syncing but exchanging NTP packets successfully
C. Master is not syncing and not exchanging NTP packets

###
Which next hop is going to be used for 172.17.1.0/24

Router(config-if)#do show ip bgp
BGP table version is 4, local router ID is 156.12.1.6
Status codes: s suppressed, d damped, h history, * valid, > best, i – internal,
r RIB-failure, S Stale Origin codes: i – IGP, e – EGP, ? – incomplete

Network Next Hop Metric LocPrf Weight Path
*>i 10.1.1.0/24 192.168.1.2 0 0 0 10000 i
*>i 10.2.2.0/24 192.168.3.2 0 0 0 10000 i
*>i 172.17.1.0/24 10.0.0.1 0 0 0 32768 i

A. 10.0.0.1
B. 192.168.1.2
C. 10.0.0.2
D. 192.168.3.2

Q: What Authentication does EIGRP use? (2 choices)
A. TKIP
B. MD5
C. Plain Text
D. WPA

The BGP one wasn’t exactly phrased that way. I’ll try to find it someone if I can.

@Sco

A. Master is syncing and exchanging NTP packets successfully

A. 10.0.0.1
it would be 10.0.0.2 if it was not valid

B.MD5
C.Plain Text