Share your ROUTE v2.0 Experience

@Dan Aki

it is 137q valid ???????????????????????????????????/

can some one explain this D& D
This is one of the frame relay DnD i remember which is asking you the missing command, this empty space is the blanks for the Drag and Drop

I just created this so that I can remember the commands for the frame relay

!
interface Serial0/3/1 (EMPTY SPACE)
bandwidth 56
ip address 10.16.0.1 255.255.255.0
encapsulation frame-relay (EMPTY SPACE)
frame-relay map ip 10.16.0.2 110 broadcast (EMPTY SPACE)

clock rate 2000000
shutdown
!
interface Serial0/3/1.2 point-to-point (EMPTY SAPCE)
ip address 10.17.0.1 255.255.255.0
frame-relay interface-dlci 100 (EMPTY SPACE)
clock rate 2000000

@wow congrats
can you explain DnD : FR anf FR LMI diffrence

@Anonymous

Your a spammer.

Which one dnd is DHCPv6?
Thanks

@Dareezy

+ DHCPv6 Server:
IPv6 address autoconfig
IPv6 enable

+ Client Interface:
IPv6 address
IPv6 DHCP Relay destination

@Anony

FR LMI is
• Address registration – allows neighbouring Cisco devices to exchange the management ip addresses
• Global addressing – Enables Frame Relay to identify interfaces in same manner as LAN
• Multicasting – provides most efficient transmission of routing protocol messages and support address resolution
• Simple flow control – supports devices that are unable to use congestion notification
• Virtual circuit – Prevents data from being transmitted in Black Hole

Dear All,

I am a bit confused about these questions. Could you please help me to answer it?

—-

Which two statements about NHRP in a DMVPN enviroment are true? (Choose two)

A. It routes traffic through the tunnel
B. It provides address resolution to route traffic
C. It can authenticate VPN endpoints
D. It can identify PIM-SM RPs over a tunnel
E. It requires each endpoint to have unique network ID

Dexter dumps says: B & C
EON dumps says: B & C

Which is correct? Thanks in advance!!

Sorry…

Dexter dumps says: A & C
EON dumps says: B & C

@Jam
Aha, thanks bro. Appreciate

@Close
Dexter dumps :
QUESTION 1
What is the NHRP role in DMVPN? (Choose 2)
A. obtains the next-hop to be used for routing
B. routes the packet through the tunnel
C. identifies the PIM-SM RP used to route the packet
D. can authenticate VPN endpoints
E. It requires each tunnel endpoint to have an unique network ID
Correct Answer: AD

So for this question :
Which two statements about NHRP in a DMVPN enviroment are true? (Choose two)

A. It routes traffic through the tunnel
B. It provides address resolution to route traffic
C. It can authenticate VPN endpoints
D. It can identify PIM-SM RPs over a tunnel
E. It requires each endpoint to have unique network ID
-> Answer : BC

Hi ALL, is anyone knows if Tagwa’s Dumps are valid? TIA.

@Khron, aaah, everything is clear already… Thank you so much!! :)

Dear All,for those who need genuine and valid CCNP dumps all formats VCE,PDF and VCE Player contact me via mail @ {email not allowed},Only serious people.

Which next hop is going to be used for 172.17.1.0/24

Router(config-if)#do show ip bgp
BGP table version is 4, local router ID is 156.12.1.6
Status codes: s suppressed, d damped, h history, * valid, > best, i – internal,
r RIB-failure, S Stale Origin codes: i – IGP, e – EGP, ? – incomplete

Network Next Hop Metric LocPrf Weight Path
*>i 10.1.1.0/24 192.168.1.2 0 0 0 10000 i
*>i 10.2.2.0/24 192.168.3.2 0 0 0 10000 i
*>i 172.17.1.0/24 10.0.0.1 0 0 0 32768 i

A. 10.0.0.1
B. 192.168.1.2
C. 10.0.0.2
D. 192.168.3.2

is this site valid for the exam?

ccnpfreak.

i reschedule my exam to 28 February i hope new dump will appear until this date

@Shufern
If this question is complete , there is only one entry for 172.17.1.0
It will be the answer , i mean 10.0.0.1

Hi
Can anyone take exam today ?

https : // www . file-upload . com /2lcargqz6oml best materials

I failed the exam previously and combining all the materials provided by ordonez and zoltam

go back to previous pages i can still remember some of those.

Hi guys, what about the question below which answer is correct ?

When use NTPv6 for IPV6 tp IPV6 Address translation ?

lack of overloading functionality
mismatched prefix allocations
or
lack of overloading functionality
one to one prefix rewrite

Thanks a lot in advance.

@ll : We have a lot of new questions here, is someone able to update the VCE File from Dexter and EON etc. ?

Can anyone take exam today ?

Can any one please tell me is it necessary to take premium membership for digitaltut for lab simulations ?

I am confused with this Q as well:

What is true about peer groups?

A. If you change the configuration the it effects all peers in the group
B. Updates can be sent with mutlicast
C. Peer groups can be send soft updates to all
D. Optimize backdoor routes

Dexter : A & C
EON: B & C

@sw
Could you pass your exam ?

Hi All,

Could you please tell me if it’s worth getting the premium @digitaltut?
The @Dexter @EON are confusing with some of their answers to the questions!

@digitaltut when is the last time the premium was updated?

^yes it is worth the money.

Can anyone confirm which one is correct or both are correct, in one question it says Allow PPPOE and the other question it says Support for PPPOE

What configurations does PPPoE allow? (Choose two)

A. Clients can connect to Multiple hosts over DMVPN
B. Client installed on native IPV6 network
C. Client connecting over ATM PVC
D. Client can be installed on the same network device as server
E. 8 Clients can be configured on 1 CPE

Answer: A,E

Which two configurations can a PPPoE client support? (Choose Two)

A. Clients can connect to Multiple hosts over DMVPN
B. Client installed on native IPV6 network
C. Client connecting over ATM PVC
D. Client can be installed on the same network device as server
E. 8 Clients can be configured on 1 CPE

Answer: A,E

Sorry typing mistake second question answers are: C,D

Hello , I pass my exam with 8 , There are new question , I remeber this question

LABs

EIGRP Stub Sim
EIGRP Evaluation Sim
OSPF Evaluation Sim

Router#show ntp associations

address ref clock st when poll reach delay offset disp
~172.31.32.2 172.31.32.1 5 29 1024 377 4.2 -8.59 1.6
+~192.168.13.33 192.168.1.111 4 69 128 377 4.1 3.48 2.3
*~192.168.13.57 192.168.1.111 3 32 128 377 7.9 11.18 3.6
* master (synced), # master (unsynced), + selected, – candidate, ~ configured

Q: Which of the following is true

A. Master is syncing and exchanging NTP packets successfully
B. Master is not syncing but exchanging NTP packets successfully
C. Master is not syncing and not exchanging NTP packets

###
Which next hop is going to be used for 172.17.1.0/24

Router(config-if)#do show ip bgp
BGP table version is 4, local router ID is 156.12.1.6
Status codes: s suppressed, d damped, h history, * valid, > best, i – internal,
r RIB-failure, S Stale Origin codes: i – IGP, e – EGP, ? – incomplete

Network Next Hop Metric LocPrf Weight Path
*>i 10.1.1.0/24 192.168.1.2 0 0 0 10000 i
*>i 10.2.2.0/24 192.168.3.2 0 0 0 10000 i
*>i 172.17.1.0/24 10.0.0.1 0 0 0 32768 i

A. 10.0.0.1
B. 192.168.1.2
C. 10.0.0.2
D. 192.168.3.2

Q: What Authentication does EIGRP use? (2 choices)
A. TKIP
B. MD5
C. Plain Text
D. WPA

Study this part

if-needed – Does not authenticate if the user has already been authenticated on a tty line.
krb5 – Uses Kerberos 5 for authentication (can be used only for Password Authentication Protocol [PAP] authentication)
local – Uses the local username database for authentication.
none- Uses no authentication.
group radius – Uses the list of all RADIUS servers for authentication.
group tacacs+ – Uses the list of all TACACS+ servers for authentication.
group group-name – Uses a subset of RADIUS or TACACS+ servers for authentication as defined by the aaa group server radius or aaa group server tacacs+ command.

**Frame Relay components**
+ SVC: A circuit that provides temporary on-demand connections between DTEs
+ LMI: A signaling mechanism for Frame Relay devices
+ DLCI: A locally significant ID
+ FECN: An indicator of congestion on the network
+ PVC: A logical connection comprising two endpoints and a CIR

**ACL**
reflexive – must be named
standard – range 1300-1399
extended – telnet …
time-based – access to device at certain times
dynamic – closest to device

**Frame relay config**
Drag each (EMPTY SPACE) line, to the right place in the configuration (i dont remember the last option. You had 5 blocks to fill and 7 possible answers)

! physical interface
interface Serial0 (EMPTY SPACE)
bandwidth 56

Q:Where to configure the DHCPv6 relay IP address for a VLAN
Do you have to enable DHCPv6 relay in the global configuration mode/VLAN interface ?
Do you have to configure something on the VLAN interface/global configuration

Q: logging console 7. Which is true ?
A. you can see debug if you’re connected in SSH
B. High CPU utilization
C. …

reouter eigrp 1
redistribute ospf 100
network 10.10.10.0 0.0.0.255
auto-summary
!
router ospf 100
network 172.16.0.0 0.0.255.255 area 10
redistribute eigrp 1
Q:what will happen to the redistributed network from EIGRP to OSPF? (phrasing was different)

A diagram with 3 routers:
+ H1 (with IPv6 IP and Loopback 1.1.1.1)
+ R1 (with IP IPv6 and Loopback 2.2.2.2)
+ R2 (with IP IPv6 and Loopback 3.3.3.3)

running with EIGRP 100 on both routers and what command you will implement so that you will see the loopback IP of R2 to be advertised at H1

A. H1(config t)#router eigrp 100
H1(config t)#no stub only
B. R2(config t)#router eigrp 100
R2(config t)#no stub receive only
C. H1(config t)#ipv6 router eigrp 100
H1(config t)#no stub only
D. R2(config t)#ipv6 router eigrp 100
R2(config t)#no stub only

Answer: B (no stub receive-only)

Which option to the command service timestamps debug enables the logging server to capture the greatest amount of information from the router?

A. uptime
B. show-timezone
C. year
D. msec

Which security level is supported throughout all SNMP versions?

A. authPriv
B. authNoPriv
C. noAuthNoPriv

Q:A network engineer is modifying RIPng timer configuration. Which configuration mode should the engineer use?
A. router(config-rtr)#
B. router(config-ripng)#
C. router(config-if)#
D. router(config)#

Whats the gateway en the global configuration
Router(config)#ip route vrf blue 0.0.0.0 0.0.0.0 192.168.1.1
Router(config)#ip route vrf red 0.0.0.0 0.0.0.0 192.168.1.2

If you type “show ip route” you will see “Gateway of last resort it not set”.
If you type show ip route vrf blue” you will see “192.168.1.1 as gateway of last resort”.

Global routing table does not overlap with VRF routing tables.

For the question:
How can you mitigate fragmentation issues between endpoints separated by a GRE tunnel? < (they changed it, they added GRE)
A. PMTU ## OK
B. TCP MSS
C. windowing
D. ICMP DF bit (this was a new answer)
Correct Answer: A

Which cisco Express Forwarding component(s) contain forwarding information? (forwarding information, they changed it)
A. FIB, adjacency table ## OK
B. adjacency table.
C. FIB, RIB , Adjanceny table
D. FIB
E. RIB
Correct Answer: A

which scenario can asymmetric routing occur?
A. active/active firewall setup
B. single path in and out of the network.
C. active/standby firewall setup
D. redundant routers running VRRP ## OK

Q:Which of these can be used for IPv4 to IPv6 communication? (new question, not sure of the exact phrasing)
A. NAT-PT ###
B. ISATAP
C. L2 to L3 VPN
D. IPSec

Router#show ntp associations

address ref clock st when poll reach delay offset disp
~172.31.32.2 172.31.32.1 5 29 1024 377 4.2 -8.59 1.6
+~192.168.13.33 192.168.1.111 4 69 128 377 4.1 3.48 2.3
*~192.168.13.57 192.168.1.111 3 32 128 377 7.9 11.18 3.6
* master (synced), # master (unsynced), + selected, – candidate, ~ configured

Q: Which of the following is true

A. Master is syncing and exchanging NTP packets successfully
B. Master is not syncing but exchanging NTP packets successfully
C. Master is not syncing and not exchanging NTP packets

I can remember that the last NTP associations on my test have * but i cant remember the stratum and reach values.

Q:Features of Netflow version 9? (CHOOSE TWO)
A. Cisco proprietary
B. IEEE standard
C. IETF
D. ingress/egress
E. ingress
F. egress
Correct Answer: C-D

How to set up IP SLA to monitor jitter between the certain limits? <= (it’s jitter now, not bandwidth)
A. Timeout (not timer)
B. Frequency
C. Threshold
D. Queue-limit
Correct Answer: c

Q:A network engineer is modifying RIPng timer configuration. Which configuration mode should the engineer use?
A. router(config-rtr)#
B. router(config-ripng)#
C. router(config-if)#
D. router(config)#

QUESTION 11
Which three statements about SNMP are true? (Choose Three)
A. The manager configures and send traps to the agent.
B. The manager sends GET and SET messages.
C. SNMPv3 supports authentication and encryption.
D. The manager polls the agent using UDP port 161
E. The MIB database can be altered only by the SNMP agent.
F. The agent is the monitoring device.
Correct Answer: BCD
In a point-to-multipoint Frame Relay topology, which two methods ensure that all routing updates are received
by all EIGRP routers within the Frame Relay network? (Choose Two)
A. Use statically defined EIGRP neighbors on the hub site.
B. Create separate address families.
C. Disable split horizon.
D. Use subinterfaces.
E. Disable EIGRP auto summary.
Correct Answer: CD
Refer to the following configuration command.
router(config)# ip nat inside source static tcp 172.16.10.8 8080 172.16.10.8 80
Which statement about the command is true?
A. Any packet that is received in the inside interface with a source IP port address of 172.16.10.8:80 is
translated to 172.16.10.8:8080.
B. Any packet that is received in the inside interface with a source IP port address of 172.16.10.8:8080 is
translated to 172.16.10.8:80.
C. The router accepts only a TCP connection from port 8080 and port 80 on IP address 172.16.10.8
D. Any packet that is received in the inside interface with a source IP address of 172.16.10.8 is redirected to
port 8080 or port 80.
Correct Answer: B
Which statement describes what this command accomplishes when inside and outside interfaces are correctly
identified for NAT?
ip nat inside source static tcp 192.168.1.50 80 209.165.201.1 8080 extendable
A. It allows host 192.168.1.50 to access external websites using TCP port 8080.
B. It allows external clients coming from public IP 209.165.201.1 to connect to a web server at 192.168.1.50.
C. It allows external clients to connect to a web server hosted on 192.168.1.50.
D. It represents an incorrect NAT configuration because it uses standard TCP ports.
Correct Answer: C
What command allows permit or deny IPv6 traffic? (they edited it)
A. traffic-filter access-list-name
B. access-list
C. access-list ipv6
D. access-group
Correct Answer: A
What are 2 protocols used for user with authentication on network device?
A. CHAP
B. Radius
C. 802.1x
D. PAP
E. TACACS+

During which DMVPN phase is spoke-to-spoke communication enabled?
A. Phase 1
B. Phase 6
C. Phase 5
D. Phase 2
E. Phase 4
Correct Answer: D
Which two phases of DMVPN allow to spoke sites to create dynamic tunnels to one another? (Choose Two)
A. Phase 1
B. Phase 2
C. Phase 3
D. Phase 4
E. Phase 5

Q:After reviewing the EVN configuration, a network administrator notices that a predefined EVN, which is known
as “vnet global” was configured. What is the purpose of this EVN? (OR)
What is the purpose of ‘vnet global”?
A. It defines the routing scope for each particular EVN edge interface.
B. It aggregates and carries all dot1q tagged traffic.
C. It refers to the global routing context and corresponds to the default RIB.
D. It safeguards the virtual network that is preconfigured to avoid mismatched routing instances.
Correct Answer: C

Q:Which encapsulation supports an interface that is configured for an EVN trunk?
A. 802.1Q
B. ISL
C. PPP
D. Frame Relay
E. MPLS
F. HDLC
Correct Answer: A

Q:IPv6 access list and need to apply it to block traffic INBOUND SSH and interface (Choose
two)
Answer: there are 5 choices 2 inbound 3 outbound so we have to choose 2 inbound choices
only (the answer had something with "access-filter in” and the other one with “access-class”)

Q:Which command instruct a PPPoE client to obtain its IP address from the PPPoe server?
A. ip address negotiated auto
B. ip address negotiated
C. pppoe enable
D. Ip address DHCP
E. Ip address dynamic

@Monsi, thanks for sharing !! I wish more people were like you.
So, I have 2 questions, that wasn’t answered yet over here.

Router#show ntp associations

address ref clock st when poll reach delay offset dispkjkjkjk
~172.31.32.2 172.31.32.1 5 29 1024 377 4.2 -8.59 1.6
+~192.168.13.33 192.168.1.111 4 69 128 377 4.1 3.48 2.3
*~192.168.13.57 192.168.1.111 3 32 128 377 7.9 11.18 3.6
* master (synced), # master (unsynced), + selected, – candidate, ~ configured,,,…l

Q: Which of the following is true

A. Master is syncing and exchanging NTP packets successfully
B. Master is not syncing but exchanging NTP packets successfully
C. Master is not syncing and not exchanging NTP packets

If there is an * it means that A is correct no ?

—–
Which next hop is going to be used for 172.17.1.0/24

Router(config-if)#do show ip bgp
BGP table version is 4, local router ID is 156.12.1.6
Status codes: s suppressed, d damped, h history, * valid, > best, i – internal,
r RIB-failure, S Stale Origin codes: i – IGP, e – EGP, ? – incomplete

Network Next Hop Metric LocPrf Weight Path
*>i 10.1.1.0/24 192.168.1.2 0 0 0 10000 i
*>i 10.2.2.0/24 192.168.3.2 0 0 0 10000 i
*>i 172.17.1.0/24 10.0.0.1 0 0 0 32768 i

A. 10.0.0.1
B. 192.168.1.2
C. 10.0.0.2
D. 192.168.3.2

answer is A ?

—–

Q: What Authentication does EIGRP use? (2 choices)
A. TKIP
B. MD5
C. Plain Text
D. WPA

This question doesn’t even make sense, since EIGRP doesn’t support plain text.

——

someone want’s to clarify the FR config ?

!
interface Serial0/3/1 (EMPTY SPACE)
bandwidth 56
ip address 10.16.0.1 255.255.255.0
encapsulation frame-relay (EMPTY SPACE)
frame-relay map ip 10.16.0.2 110 broadcast (EMPTY SPACE)

clock rate 2000000
shutdown
!
interface Serial0/3/1.2 point-to-point (EMPTY SAPCE)
ip address 10.17.0.1 255.255.255.0
frame-relay interface-dlci 100 (EMPTY SPACE)
clock rate 2000000

Thanks monsi. I have all the questions compiled from the last 3-4 pages in a word document. Trying to make a vce but can’t find the software.

@Coldwindfly

What configurations does PPPoE allow? (Choose two)

A. Clients can connect to Multiple hosts over DMVPN
B. Client installed on native IPV6 network
C. Client connecting over ATM PVC
D. Client can be installed on the same network device as server
E. 8 Clients can be configured on 1 CPE

Answer: A,E

@Easy there are 2 difererent NTP Question

The firts question with * with 377 A. Master is syncing and exchanging NTP packets successfully
The Second Question # with 377 B. Master is not syncing but exchanging NTP packets successfully

* master (synced), # master (unsynced), + selected, – candidate, ~ configured

Characters before the address have these definitions:

* Synchronized to this peer
# Almost synchronized to this peer
+ Peer selected for possible synchronization
– Peer is a candidate for selection
~ Peer is statically configured

•377 octal = 11111111 binary, which indicates the NTP process received the last eight packets.

Which next hop is going to be used for 172.17.1.0/24

Router(config-if)#do show ip bgp
BGP table version is 4, local router ID is 156.12.1.6
Status codes: s suppressed, d damped, h history, * valid, > best, i – internal,
r RIB-failure, S Stale Origin codes: i – IGP, e – EGP, ? – incomplete

Network Next Hop Metric LocPrf Weight Path
*>i 10.1.1.0/24 192.168.1.2 0 0 0 10000 i
*>i 10.2.2.0/24 192.168.3.2 0 0 0 10000 i
*>i 172.17.1.0/24 10.0.0.1 0 0 0 32768 i

A. 10.0.0.1 ## CORRECT
B. 192.168.1.2
C. 10.0.0.2
D. 192.168.3.2

Q: What Authentication does EIGRP use? (2 choices)
A. TKIP
B. MD5 ## Correct
C. Plain Text ## Correct
D. WPA

The router uses two types of authentication:
• Simple password authentication (also called plain text authentication)—Supported by Integrated System-Integrated System (IS-IS), Open Shortest Path First (OSPF), and Routing Information Protocol Version 2 (RIPv2)
• MD5 authentication—Supported by OSPF, RIPv2, BGP, and EIGRP

If the service password-encryption command is not used when implementing EIGRP authentication, the key-string will be stored as plain text in the router configuration. If you configure the service password-encryption command, the key-string will be stored and displayed in an encrypted form; when it is displayed, there will be an encryption-type of 7 specified before the encrypted key-string.

someone want’s to clarify the FR config ?

For This question in the exam show Frame Relay configuración in drag and drop boxes

interface —–Space Blank —— Serial0/3/1
banwith 56
space Blank —encapsulation frame-relay
space Blank—- ip address
no shutdown

Space BlanK —interface Serial0/3/1.2 point-to-point
Space BlanK –ip address 10.17.0.1 255.255.255.0
Space BlanK –frame-relay interface-dlci 100

clock rate 2000000
shutdown
!

My recommendation is that you learn to configure Frame Relay physical interfaces with Ip, Subinterfaces point-point and Point-Multipoint for the case in your exam

@Monsi Thank you very much. How About Lab, like EIGRP Eva and OSPF Eva, it same or just different ip? thx

For NTP
https://www.cisco.com/c/en/us/support/docs/ios-nx-os-software/ios-software-releases-110/15171-ntpassoc.html

@monsi, Thanks a lot for your help! I’m sure you helped everyone ever here!
I’m doing the test tomorrow, hopefully, I’ll pass and update you guys more accurately.

I can only agree with that !
@monsi ….many thanks for your help !

@Fansy: please share us your perception regarding the questions, do we have the most of the questions covered or do we have a bigger lack ?

Many Thanks in advance !

@monsi, congratulations to your exam and thanks a lot for your help, we appreciate it very much!

@Easy, good luck to your exam and please keep us also up to date, thank you in adavance!

Thanks monsi! finally someone able to remember it.. i will take the exam again this month and hopefully pass

heeeeeeeellllllllllllo everyone
i need dumps plz >> which dumps is valid

Where’s the DMVPN DND?

@Easy what dumps did you use?

ccnp easyeasy~

@x, I used dexted dumps which are probably like 40% valid, and copy all the information from the last pages to a notepad, and hope to pass.
Right now there isn’t any valid dump.

Okay @Easy, i am just starting to prepare thanks for the tip, before i went here, i read an old cert guide book and been doing networking so i am much familiar with the questions but will use dumps so that i could be sure.

@Easy Good luck tomorrow!
And please if it is possible to remember Frame Relay dnd options but I think there will be IEFT :)
http://www.ciscopress.com/articles/article.asp?p=170741&seqNum=2

The enterprise network WAN link has been receiving several denial of service attacks from both IPv4 and IPv6
sources.
Which three elements can you use to identify an IPv6 packet via its header, in order to filter future attacks?
(Choose three.)
A. Traffic Class
B. Source address
C. Flow Label
D. Hop Limit
E. Destination Address
F. Fragment Offset
Dexter dump Correct Answer: BCE
Digiltut Answer: A C D

Can someone help? which is the correct answer

Other than a working EIGRP configuration, which option must be the same on all routers for EIGRP
authentication key rolleover to work correctly?

A. SMTP
B. SNMP
C. Passwords
D. Time

Correct Answer: C or D?