Share your ROUTE v2.0 Experience

@Ada please remove the space in between

@CiscoTake .. did you get sorted for labs? I have them is needed in GNS3.. I recreated them

thanks @Ada my email is {email not allowed}

ok I’ll try again XD cisco daddy at mail. com

as i said im sure about my answer is DE
Which two statements about NHRP in a DMVPN environment are true? (Choose two)
a. It requires each endpoint to have a unique network ID
b. It routes traffic through the tunnel
c. It can identify PIM-SM RPs over a tunnel
d. It can authenticate VPN endpoints
e. It provides address resolution to route traffic
answer: D and E 100% sure
refernce : https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_conn_dmvpn/configuration/xe-3s/sec-conn-dmvpn-xe-3s-book/sec-conn-dmvpn-share-ipsec-w-tun-protect.html

Hello

Can anyone please share the latest dump?

Thanks.

@SOSO

I AM NOT SURE CHEK THIS POST:

The first thing you’re likely to notice is that the tunnel does not have an explicit destination specified. This is because multipoint tunnels are built dynamically from the DMVPN spokes to the hub router; the hub router doesn’t need to be preconfigured with spoke addresses. Also note that the tunnel mode has been designated as multipoint GRE. ip nhrp network-id 1 uniquely identifies the DMVPN network; tunnels will not form between routers with differing network IDs. ip nhrp multicast dynamic enables forwarding of multicast traffic across the tunnel to dynamic spokes (required by most routing protocols).

nhrp
1- provide address resolution
The Next Hop Resolution Protocol (NHRP) is an extension of the ATM ARP routing mechanism that is sometimes used to improve the efficiency of routing computer network traffic over Non-Broadcas…
2-can authenticate rndpoints
The commands ip nhrp network-id and ip nhrp authentication [Key] identify and authenticate the logical NHRP network. The [ID] and the [Key] must match on all routers sharing the same GRE tunnel.

@ CiscoDaddy

i am still unable to configure ipv6 ospf v-link lab if you have please share it or if you allow me i can send you an email so you can reply me with labs …

@SOSO THANKS A LOT

Which two statements about NHRP in a DMVPN environment are true? (Choose two)
a. It requires each endpoint to have a unique network ID
b. It routes traffic through the tunnel
c. It can identify PIM-SM RPs over a tunnel
d. It can authenticate VPN endpoints
e. It provides address resolution to route traffic
answer: D and E

THIS QUESTION DOSENT EXIT CONFIRM PLEASE ???????????????????????????”

4. What is the NHRP role in DMVPN? (Choose 2)
a) obtains the next-hop to be used for routing
b) routes the packet through the tunnel
c) identifies the PIM-SM RP used to route the packet
d) don’t remember
Answer: A,B

for the option A :It requires each endpoint to have a unique network ID.
it not required since we can configure multiple tunnel int with the same network ID to mapping database populated

yes maximo
the officiel question from CISCO is
Which two statements about NHRP in a DMVPN environment are true? (Choose two)
a. It requires each endpoint to have a unique network ID
b. It routes traffic through the tunnel
c. It can identify PIM-SM RPs over a tunnel
d. It can authenticate VPN endpoints
e. It provides address resolution to route traffic

the other is the same but we know that who put the question here seems not remember the correct syntax so the answers can be false

@SOSO AND ANYONE

THIS TWO QUESTIONS ONE IS FOR SERVER AND ONE FROM CLIENT. DO YOU KNOW THE QUESTION EXACT IN THE EXAM??????????

11111.Which two commands do you need to implement on a router to support pppoe client? (choose Two) !!!!!!THIS IS FOR CLIENT!!!!!

A. peer default ip address pool
*B. mtu
C. bba-group pppoe
D. pppoe enable group
*E. pppoe-client dialer-pool-number

ANSWARE: B and E

x11111.Which two commands do you need to implement on the CALLING router to support the pppoe client ? (choose Two) !!!!!!!!THIS IS FOR SERVER !!!!!!

*A. peer default ip address pool
B. mtu
-C. bba-group pppoe
*D. pppoe enable group
E. pppoe-client dialer-pool-number

ANS: I DONT KNO WWHICH OF THIS THREE (AED)

IN THIS QUESTION EVREYONE THINK IS NUMBER 5 ???????

up/down INTERFACE WHAT LOG SEVERITY LEVEL?

3
4
*5
0

@ sky @AS –> OK guys now it is working. I reinstalled GNS3 (BTW new version is 2.1.0) and it works now :)

@maximo
yeah this is a example of what i said , this quesion is not clear , because who put it doesnt remember correctly , so we didnt know the exact source up/down if line protocol or link inteface

up/down INTERFACE WHAT LOG SEVERITY LEVEL?
3
4
*5
0
for me while he put interface i think its clear its about link (interface) so answer is 3
if they say line protocol the answer is 5 but i remove this choise, because there is another question from the dump about what severity .. line protocol …

about the question of server or client , i think the 2 qust are the same but i cant told you if CISCO want the config of server or client , you can figured out at exam hhhh

@SOSO

ARE YOU AGRE WHIT MY THIS QUESTION IN PROCYER VCE IS (SOURCE, FLOW AND DESTINATION)

The enterprise network WAN link has been receiving several denial of service attacks from
both IPv4 and IPv6 sources. Which three elements can you use to identify an IPv6 packet
via its header, in order to filter future attacks? (Choose three.)

*trafic class
source address
*flow label
*hop limit
destination address
fragment offset

FOR MY: TRAFFIC CLASS, FLOW LABEL AND HOP LIMIT

@maximo

No new questions but all those shared by different people on this forum in last 2 to 3 weeks

All 7 questions shared above by CiscoTake were in exam

best of luck

am off to tshoot now ….

@FIDDY

CAN YOU PLEASE HELP US WHIT THIS CONFUSE QUESTIONS ???

11111.Which two commands do you need to implement on a router to support pppoe client? (choose Two)

A. peer default ip address pool
*B. mtu
C. bba-group pppoe
D. pppoe enable group
*E. pppoe-client dialer-pool-number

x11111.Which two commands do you need to implement on the CALLING router to support the pppoe client ? (choose Two)

*A. peer default ip address pool
B. mtu
-C. bba-group pppoe
*D. pppoe enable group
E. pppoe-client dialer-pool-number

which three NTP operating modes must the trusted-key command be configured on for authentication to operate properly?

*cliente
peer
*brodcast
interface
*server

WHICH TYPE OF INFORMATION IS DISPLAYED WHEN A NETWORK ENGINEER EXECUTES THE SHOW TRACK 1 COMMAND ON THE ROUTE?

INFORMATION ABOUT TRACKIN list 1
TIME TO NEXT POLL FOR TRACK OBJECT 1
INFORMATION ABOUT THE IP ROUTE TRACK TABLE
*TRACKING INFORMATION STATISTICS

PLEASEEEEEEEEEEEEEE

soso , yes all answers at its me seems correct
dont be afraid

@SOSO

I PROMISE YOU THAT CUNADO PASS THE EXAM WILL DELIVER YOU A DOCUMENT WITH THE BEST POSSIBLE ANSWARES

IN TWO DAYS DO MY EXAM

good luck bro me too i have exam next week , lets do it …

@CiscoTake

OSPF v3 should work fine. I tried it for several time before

email me @CiscoTake on ciscodaddy at mail. com

Are “it’s me vce” and ” ROUTEv1.5 (updated by procyber 01.11.2017)” the same?
If not, which is more up to date?

@Cisco Take
can you please tell me .

How can I verify IPv6 ospf virtual-link sim?

@Ashik
You can use below commands to verify the OSPFv3 virtual link

1. show ipv6 ospf virtual-link

2. show ipv6 ospf interface brief

Not sure wehter those will work in the exams

@Sky

Do I want to execute this command on which router? Router 1?

@sky

I got the solution.

Router 4 loopback ip address should be on Router 1 routing table.

@sky

I dont know what is the issue all the labs downloaded are okay from zip file but this Ipv6 ospf did not even have configuration for ipv6 ospf as all router show nothing while executing command “show run”

@Ashik i have issues with this lab so cant help you…

CiscoDaddy please check your mail .. :)

@Cisco take
I did it. I saw the R4 loopback on R1 .

I did’t get your mail

@ashik i didnt share email here just send email to ciscodaddy so he can reply .. if you have any email account which hides your identity please share here so i can request you to send me this Ipv6 ospf virtual link lab

@Cisco take
Drop me a mail
ashikonline92 @ gmail.com

@ashik please check .. your account

@Cisco take
Check your mail

which version you ppl are using for labs i am using 0.8.3 as recommended by this forum… ipv6 ospf virtual link topology is not configured and i am unable to configure ipv6 commands even cant able to enable ipv6 shows err0r

the issue wit tis lab is wrong config:
interface Loopback0
no ip address
ipv6 address FEC0:4::4/28
ipv6 ospf 1 area 11

it shoul be ipv6 ospf 1 area 54

thank you all … figure out the problem as gns3 opens the topology under c2691 which does not support ipv6 so i have to configure advance router c7200 for this sim to run properly ….

@lena once i run it properly then i can see this issue :) if it is so

Can somebody share me the link to download latest VCE manager software

I’d like to take this moment and thank ya’ll. I’ve cleared the exam.. Didn’t get lot of new questions but the ones I got are mentioned by Bravo on this page. All the best to ya’ll.

@SOSO
thanks to send me the link for the latest dump , as well as the labs please
Michel-chalaby@ Hotmail . com

@Tim :please give us more ditails about exam ..

@Ada.. haven’t received email bud CiscoDaddy (at) mail. com

@maximo
which three NTP operating modes must the trusted-key command be configured on for authentication to operate properly?
*cliente
*peer
*brodcast
interface
server

hello guys,

can anyone please share new question after 470Q dump ?
thank you in advance..

@AS or anyone

help my whit this question

why it´s beacuse i am confius whit this question.

which three NTP operating modes must the trusted-key command be configured on for authentication to operate properly?
*cliente
*peer
*brodcast
interface
server

@ maximo
I give you correct answer…

@AS

Why i need to explain please