Share your ROUTE v2.0 Experience

Guys,
Can anyone please post the New DnD Question from DMVPN topic.

The enterprise network WAN link has been receiving several denial of service attacks from both IPv4 and IPv6 sources. Which three elements can you use to identify an IPv6 packet via its header, in order to filter future attacks? (Choose three)
A. Traffic Class
B. Source address
C. Flow Label
D. Hop Limit
E. Destination Address
F. Fragment Offset

what is correct answers

@ Ali

The enterprise network WAN link has been receiving several denial of service attacks from both IPv4 and IPv6 sources. Which three elements can you use to identify an IPv6 packet via its header, in order to filter future attacks? (Choose three)
A. Traffic Class
B. Source address
C. Flow Label
D. Hop Limit
E. Destination Address
F. Fragment Offset
what is correct answers

Answer: A C D

@ Hiba

QUESTION 24
Refer to the exhibit
configure terminal
ip flow-export destination 192.168.10.1 9991
ip flow-export version 9
How can you configure a second export destination for IP address 192.168.10.1?
A.Specify a different TCP port
B.Specify a different UDP port
C.Specify a VRF
D.Configure a version 5 flow-export to the same destination
E.Specify a different flow ID
Answer : C
..
QUESTION 25
If you configure one router in your network with the auto-cost reference
bandwidth 100 command, which effect
on the data path is true?
A.The data path remains the same for all links.
B.The data path changes for 10 Mbps links only.
C.The data path changes for all links.
D.The data path changes for 10 Gbps links only.
Answer: A

…
QUESTION 45
How route tags can be set?
A.ONLY within route tags
B.within taglists
C.can be set with ONLY route-maps
D.can be set DIRECTLY within route maps.
E.only used on link state RPs.
Answer B D this has been reworded from previous exam question, just remember it is NOT only.
……
Same Q 47 I’m confused with this question too, only can think E, Q48 is OK i guess unless anyone else knows better?

QUESTION 47 im confused with his question too!
When use NPTv6 for IPV6 to IPV6 Address translation? (Choose two)
A.stateful address translation
B.a limit of 32 1-to-1 translations
C.lack of overloading functionality
D.identify all interface NAT inside or outside
E.one-to-one prefix rewrite
F.mismatched prefix allocations
Answer: C F
Section: (none)
Explanation/Reference:

QUESTION 48
Two limitations when use NPTv6 for IPV6 to IPV6 Address translation?
A.stateful address translation
B.a limit of 32 1-to-1 translations
C.lack of overloading functionality
D.identify all interfaceas NAT inside or outside
E.1-to-1 prefix rewrite
F.mismatched prefix allocations
Answer: C F

@ R1th1

someone posted this above after exam.

The DND about DMVPN is (this is my answer)
hub -> there is a word (next-hop server)
spoke -> “device …. dynamic address”
nhrp -> ” protocol
mgre -> “multi tunnel endpoint”

@Weirdo
can u please send me the route dumps…my exam is in few days…plz
E-mail:
nurwanreza79@ gmail.com

passed today my route exam 9xx eon dum is vaild and dmvpn d&d and lmi

@Ammar

Congrats!! do you remember any mor about the d&d, must have been more than 2?

What is true about peer groups? (Choose two)
A. Optimize backdoor routes
B. If you change configuration then it effects all peers in the group
C. Peer groups can send soft updates to all
D. Updates can be sent with multicast

which one is true from above mcqs

@ali:

What is true about peer groups? (Choose two)
A. Optimize backdoor routes
B. If you change configuration then it effects all peers in the group
C. Peer groups can send soft updates to all
D. Updates can be sent with multicast
B,C

@Doleeb
Thanks for your reply

Passed today with full score!

Later i will post the answers for every new question…
About dexter dump i can say it’s valid but max 10 question were from there!
Lot of new questions similar from dexter but reworded
Simulations were the same and dnd too

Hi, everyone, I passed my exam with 920 earlier today. Almost all questions from EON’s dump were there, some of them had the options changed a little bit, but they are essentially the same.

DnD:
LMI
Frame Relay components
Router, User and AAA Server
DMVPN, the one with hub, spoke, nhrp and mGRE

Labs: Redistribution, PBR and Stub with summarization.

Other questions not in EON’s dump that I can remember:

-What algorithm is used in EIGRP? I Answered Dual
-Something like this: when using Unicast Reverse Path forwarding, what is the first thing a router does? I Answered check if the traffic matches an acl.
-The other one was something like this: How to summarize Rip when redistributing to eigrp? The 4 options were commands, I don’t remember them.

If I remember more questions I’ll post them.

Dear Zuga, below two questions are from EON, its confusing, can you help which is right answer? When use NPTv6 for IPV6 to IPV6 Address translation? (Choose two)
A.stateful address translation
B.a limit of 32 1-to-1 translations
C.lack of overloading functionality
D.identify all interface NAT inside or outside
E.one-to-one prefix rewrite
F.mismatched prefix allocations
Answer: C F
Section: (none)
Explanation/Reference:

QUESTION 48
Two limitations when use NPTv6 for IPV6 to IPV6 Address translation?
A.stateful address translation
B.a limit of 32 1-to-1 translations
C.lack of overloading functionality
D.identify all interfaceas NAT inside or outside
E.1-to-1 prefix rewrite
F.mismatched prefix allocations
Answer: C F

To be honest, I don’t know if the answers are correct. May exam had only the first question and I answered the same as the dumps. Maybe they are right, maybe not.

Other one I remember that comes in the dumps and some users had discussed and I also believe the answer in the dumps is wrong:

Which value GRE tunnel uses to identify endpoints?
Dumps say DLCI, but I answered IP address.

@Bumble Bee Answer is CF in both cases.

@Zuga your IP Address answer is correct :)

What is true about peer groups? (Choose two)
A. Optimize backdoor routes
B. If you change configuration then it effects all peers in the group
C. Peer groups can send soft updates to all
D. Updates can be sent with multicast

which one is correct ?

For those that have taken the exam; which dumps are valid. Is it Dexter or EON?

@Ali:
B, C

Has anyone tried using just the question from Digitaltut for the exam; if so, is it helpful?

EIGRP STUB LAB

On Router R3 command sh running-config
output will be “eigrp stub receive-only”, we have to replace it with “eigrp stub”

R3#configure terminal
R3(config)#router eigrp 123
R3(config-router)#no eigrp stub receive-only
R3(config-router)#eigrp stub
R3(config-router)#exit
R3(config)#exit
R3# sh ip route
e.g 9 subnets in the output

Go to Router R4 and on its s0/0 port implement the summary route

R4>enable
R4#configure terminal
R4(config)#interface s0/0
R4(config-if)#ip summary-address eigrp 123 10.2.0.0 255.255.0.0

Jump back to R3 sh ip route

must be 2 subnets

Was just wanted to revise it so thought share it here I will do the revision and it might help someone.

I haven’t studied Dexters dumps. But 90% of the questions in todays exam, came from EONs.

@zuga actually all the questions are in the Dexter’s dumps, just few of them are new

congratulations on passing the exam

@safiah, yes they are but to be more confident and well prepared dumps help too. Dexter’s dumps are the best so far, EON dumps are the extract of dexter’s dumps.

can any one tell me please that in dnds we need to select dnds in order or not

e.g nat 64 has two options and npt6 has two options

please reply fast today i have exam

please reply

not important until and unless it has been asked

@Zuga
which one is DMVPN DnD, I can’t find on dexter dump?
Gonna take exam tomorrow :(

@Elias there will be abbreviations and you have to match the definitions I reckon.
DMVPN, the one with hub, spoke, nhrp and mGRE

10. How does an EVN provide end-to-end virtualization and separation for data traffic from multiple networks?
A. It tags traffic with a virtual network tag at the trun interface
B. It tags traffic with an 802.1q tag at the edge interface.
C. It tags traffic with a virtual network tag at the edge interface
D. It tags traffice with an 8021.1 tag at the trunk interface.
which one is true A or D ?

In which scenario can asymmetric routing occur?
a. active/active firewall setup
b. single path in and out of the network
c. active/standby firewall setup
d. redundant routers running VRRP

A or D

guys, I am new to this site. Will some one tell me where can find valid dumps? Thanks

EON VCE file showing error.. how to open it?

@ ordonez
please check previous page he updated again it will work

@Ali Both questions answer is “A”

@Ghauri please search for page 83, Dexters dumps and 12 new questions in the further pages

@Ghauri try if this works
https://drive.google.com/open?id=1AFl4Vc9Gyy7HJHVffSh6p0Fl09kx011s

@WSB
Thanks bro

Hi im currently ccna certified from PH. A graduating college student. Should I take ccnp route training or gain work experience first? Thanks

Hi im currently ccna certified from PH. A graduating college student. Should I take ccnp route training or gain work experience first? Thanks in advance

@zuga
in “Labs: Redistribution, PBR and Stub with summarization.”

what do you mean by summarization?

@zuga
nervermind, I missed the EIGRP Stub on my browser. silly me.

Which value does GRE tunnel use to identify the end points or destination

ANSWER: IP Address

Why would you use DLCI for GRE tunnel? correct me if i am wrong

R1:
interface Tunnel100
tunnel mode gre
ip address 102.1.1.1 255.255.255.0
ipv6 enable
tunnel source Loopback0
tunnel destination 2.2.2.2

R2:

interface Tunnel100
tunnel mode gre
ip address 102.1.1.2 255.255.255.0
ipv6 enable
tunnel source Loopback0
tunnel destination 1.1.1.1

You are absolutely correct my friend :)

HI GUYS , @WBS

A question with illustration, having one hub two spokes, running EIGRP and loopbacks on all routers. Hub is able to see loopbacks of all the two spokes. Question asked why the spokes are not seeing each other’s loopbacks.

a. H1(config t)router eigrp 100
H1(config t)no stub only
b. R2(config t)router eigrp 100
R2(config t)no stub receive only
c. H1(config t)ipv6 router eigrp 100
H1(config t)no stub only
d. R2(config t)ipv6 router eigrp 100
R2(config t)no stub only

Answer: D OR B ? A

@Moha

In the exam you do not have that “D” option.

The correct answer is:

ipv6 router eigrp 100
No stub receive-only

@Ordonez

Your are absoluty right

I got full score and my answer were: ip address