Share your ROUTE v2.0 Experience

All drag and drops will likely be in the exam.. they are worded slightly different, and in various order.
Labs, I would expect to do 4, and 2 simulations. questions where almost uptodate.. but that was a week ago.

I had an initial issue with PBR.. use the ? for commands to make sure you enter the group-policy & access-list right. For redistribution I did not read that it should flow via fast-ethernet if available.. and when I checked the route table the data did not changce.. so I’m not sure distance eigrp 90 105 is relevant.

Be sure to use ? for commands. It is allowed.

If anyone has the latest Route videos I have the latest switch.. will trade.

guys can you give me a link where i can download PDF E-books for route. I am more comfortable reading e-books. TIA

@Anonymous, CiscoDaddy contributed a lot in this group, I honestly don’t know what you’re talking about.

Below are the new questions, and most of them were shared by Irrelevant, Maximo, et al.

Wish you all the best in your exam,

https://drive.google.com/drive/folders/1O6cV28TjRuLn2eyKsiB92wuM1R_Ej2EN?usp=sharing

@anonymous Ciscodaddy was one of the MVPs the last month. props to you

guys help me with 300-115 latest dump.

Thanks CiscoDaddy – we know you contributed a lot

Just a confirmation if you can regarding following question ?

I believe you had valid reasoning for option and C and D and i guess its correct but what did you go for in exam ? As many says its B and E

A. peer default ip address pool
B. mtu
C. bba-group pppoe
D. pppoe enable group
E. pppoe-client dialer-pool-number
Aswers: B and E

Hi

A route map was configured and it was distributing OSPF external routes
A. Distributing E1 only
B. Distributing E1 and E2 using prefix list
C. Distributing E1 and E2 using access list
D. Distributing E2 routes

Answer: B or C

Does anyone have a link for me to get the Labs? The gns files.

@Maximo
wishing you all the best for the exams. I also going to sit for the exam soon. May be within a week. Hope Zitto questions are useful.

Please also feedback after the exam will be helpful to all

Can someone please Answer this question.

Frame Relay LMI autosense. what is true?
A. line should be up and protocol should be down
B. protocol must be up
C. it only works on DTEs
D. it only works on DCEs

Answer : AD or AC

@soso, @maximo,@Zitto @Fiddy @ Cisco daddy

pleaase guys please help me out.
How to study for DnD questions?What are the most DnD questions are coming in the exam?
Do i want to be mast in that 31 DnD questions?
Please help me I am facing my exam in Two weeks.

Thanks in advanced.

@CiscoDaddy
I have CBT Nugget for route and cisco live lessons is this what u need? I already passed the switch exam do you need switch lessons too?

@soso, they are randomized, please study them all(31 of them).

@Ada, would you kindly share the Switch material.

@zitto

We have the necessary information or even if I’m short I do my exam in two days I need to know the maximum to help and help these guys while more information has more information I can contribute to this group by passing help my

ANYONE

We have the necessary information or even if I’m short I do my exam in two days I need to know the maximum to help and help these guys while more information has more information I can contribute to this group by passing help my

HELP MYYYYY

SOMEONE HAS EXTRA INFORMATION WHILE MORE CONTRIBUTE I JUDGE GIVE EVERY DETAIL OF THE EXAMINATION EVERY QUESTION I DO NOT FORGET NIGUNA AND PROVIDE EACH OF THEM NEW IF THERE ARE THERE, I AM TWO DAYS OF CHILDREN AND I NEED OF YOU THAT IS WHY I SWEAR HAPPEN ALL THE INFO AND CONTINUE SUPPORTING DO NOT ABANDON ME THAT I WILL NOT ABANDON IT

Ada share switching dumps

@Zitto
I passed it last year but study materials are all same if you want give me your Email and I will share it with you.

I passed several days ago.

I thought the exam was tough but fair.

I would suggest doing plenty of base study first. Then pay digital subscription and practice the Labs and questions on this site as final preparation.

I found VPN tricky so study hard around this technology

Good luck all

@Jaga Congratulations first of all

Which dumps you refer for the exams?

@Ada, molatelo glenn at gmail dot com. No spaces

@Jaga: do you remember some of the new questions?

pleaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaase
is the frame relay configuration in the curriculum in exam

is the frame relay configuration in the curriculum in exam

@ sky @ mar22

ItsMe 480 (v4) plus new questions shared on this forum

Dont recall any new questions but some were worded a bit differently I think

Sorry I find exams quite stressful and don’t remember that much about them afterwards

Someone please send me the 300-101 dumps.

Does anyone have a link for me to get the Labs? The GNS files. Please guys, I write exam soon.

@janki/hsn

Go to hell

@smeagol use the following link to download all labs for GNS3 v 0.8.x

https://www.digitaltut.com/practice-real-route-labs-with-gns3#more-672

Guys, which answer is correct for below ? was in exam
Which two statements about NHRP in a DMVPN environment are true? (Choose two)
a. It requires each endpoint to have a unique network ID
b. It routes traffic through the tunnel
c. It can identify PIM-SM RPs over a tunnel
d. It can authenticate VPN endpoints
e. It provides address resolution to route traffic

answer: D and E ?

In which scenario can asymmetric routing occur?
a. active/active firewall setup
b. single path in and out of the network
c. active/standby firewall setup
d. redundant routers running VRRP
answer? D?

Guys help me with 300-101 or 300-135 latest dump.

Cis.jaber at Gmail dot com

i am preparing for ROUTE in this month.can anybody please share the link of latest valid dumps.thanks in advance

@bravo
where did you get this questions
Which two statements about NHRP in a DMVPN environment are true? (Choose two)
a. It requires each endpoint to have a unique network ID
b. It routes traffic through the tunnel
c. It can identify PIM-SM RPs over a tunnel
d. It can authenticate VPN endpoints
e. It provides address resolution to route traffic

i think is the officiel question from cisco is that

where did you get this questions
Which two statements about NHRP in a DMVPN environment are true? (Choose two)
a. It requires each endpoint to have a unique network ID
b. It routes traffic through the tunnel
c. It can identify PIM-SM RPs over a tunnel
d. It can authenticate VPN endpoints
e. It provides address resolution to route traffic

not this one
What is the NHRP role in DMVPN ? (Choose two)
A. obtains the next-hop to be used for routing
B. routes the packet through the tunnel
C. identifies the PIM-SM RP used to route the packet
D. can authenticate VPN endpoints
E. It requires each tunnel endpoint to have an unique network ID

plz answer me if you get a dump from a vendor

from me
Which two statements about NHRP in a DMVPN environment are true? (Choose two)
a. It requires each endpoint to have a unique network ID
b. It routes traffic through the tunnel
c. It can identify PIM-SM RPs over a tunnel
d. It can authenticate VPN endpoints
e. It provides address resolution to route traffic
answer: D and E
In which scenario can asymmetric routing occur?
a. active/active firewall setup
b. single path in and out of the network
c. active/standby firewall setup
d. redundant routers running VRRP
answer A

@soso i got this question in exam. 3 days ago i failed with 780score.

and also this questions which i remembered.

Guys, are this answers correct?

1. In a point-to-multipoint Frame Relay topology, which two methods ensure that all routing updates are received by all EIGRP routers within the Frame Relay network? (Choose Two)
A. Use statically defined EIGRP neighbors on the hub site.
B. Create separate address families.
C. Disable split horizon.
D. Use sub interfaces.
E. Disable EIGRP auto summary.

C,A.

2. access-list 1 permit 172.16.1.0 0.0.0.255
ip nat inside source list 1 interface gigabitethernet0/0 overload

You have correctly identified the inside and outside interfaces in the NAT configuration of this device. Which configuration is true?
a. dynamic nat
b. PAT
c. NAT64
d. static NAT

B.

3.Which two commands must you configure on a DMVPN hub to enable phase 3? (Choose Two)
A. ip nhrp interest
B. ip nhrp redirect
C. ip nhrp shortcut
D. ip nw id
E. ip nhrp map
F. ip redirects

B,C.

4.Which two routers can do OSPF route summarization. (Choose Two)
A. Area Border Router
B. Autonomous System Boundary Router
C. Summary router
D. internal router
E. Backbone route

A,B.

5. Which two OSPF network types can operate without a DR/BDR relationship? (Choose Two)
A. Point-to-multipoint
B. Point-to-point
C. nonbroadcast
D. nonbroadcast multi-access
E. broadcast
Answer: AB

6. Which condition can cause unicast reverse path forwarding to fail?
a. portfast security violation
b. asymmetric routing
c. CTR convergence
d. split horizon

B.

7. When a packet is denied by an IPv6 traffice filter, which additional action does te device perform?
a. A creates a null route for te destination and adds it to the route table.
b. It scans the rest of the ACL for a permit entry matching the destination.
c. It generates a TCP Fin bit and sends it to the source.
d. It generates an ICMP unreachable message for the frame.

D

8.Which three TCP enhancements can be used with TCP selective acknowledgments? (Choose three.)
A. header compression
B. explicit congestion notification
C. keepalive
D. time stamps
E. TCP path discovery
F. MTU window

B, C, D

9.network engineer wants an NTP clients to be able to update the local system without updating or synchronizing with the remote system. Which option for the ntp access-group command is needed to accomplish this?
A. serve
B. query-only
C. serve-only
D. peer

D.

10. How does an EVN provide end-to-end virtualization and separation for data traffic from multiple networks?
A. It tags traffic with a virtual network tag at the trun interface
B. It tags traffic with an 802.1q tag at the edge interface.
C. It tags traffic with a virtual network tag at the edge interface
D. It tags traffice with an 8021.1 tag at the trunk interface.

A.

11.Which command enables NAT-PT on an 1Pv6 interface?
A. 1Pv6 nat-pt enable
B. ipv6 nat
C. ipv6 nat-pt
D. ipv6 nat enable

B.

12. Which problem can be caused by latency on a UDP stream?
A. The device that sends the stream is forced to hold data in the buffer for a longer period of time.
B. The overall throughput of the stream is decreased.
C. The device that receives the stream is forced to hold data in the buffer for a longer period of time.
D. The devices at each end of the stream are forced to negotiate a smaller window size.

B.

13Which two statements about GRE tunnel interfaces are true?
A. To establish a tunnel, the source interface must be in the up/up state.
B. A tunnel destination must be mutable, but it can be unreachable.
C. A tunnel can be established when the source interface is in the up/down state.
D. To establish a tunnel, the source interface must be a loopback.

A,B.

14. How does an EVN provide end to end virtualization and separation for data traffic from multiple networks?
a. It tags traffic with a virtual network tag at the trunk interface
b. It tags traffic with an 802.1q tag at the edge interface
c. It tags traffic with a virtual network tag at the edge interface
It tags traggec with an 802.1q tag at the trunk interface

A.

15.Which two debug commands can you use to view issues with CHAP and PAP authentication? (Choose Two)
A. debug tacacs
B. debug PPP authentication
C. debug radius
D. debug aaa authentication
E. debug ppp negotiation

B,E.

16. Which three problems result from application mixing of UDP and TCP streams within a network with no QoS? (Choose three.)
A. starvation
B. jitter
C. latency
D. windowing
E. lower throughput

A, C, E.

17. Considering the IPv6 address independence requirements, which process do you avoid when you use NPTv6 for translation
A. rewriting of higher layer information
B. checksum verification
C. ipv6 duplication and conservation
D. IPSEC AH header modification

A.

18. Which cisco Express Forwarding component maintains Layer 2 addressing information?
A. dCEF
B. adjacency table.
C. FIB
D. fast switching
E. RIB

B.

19. Which Cisco Express Forwarding component maintains Layer 2 addressing information?
a. fast switching
b. RIB
c. FIB
d. adjacency table

D.

20. Which value does a Cisco router use as its default username for CHAP authentication?
a. cisco
b.its own hostname
c.ppp
d. chap

b.

21.Which version or versions of NetFlow support MPLS?
a. netflow version 5
b. netflow version 9
c. netflow versions 8 and 9
d. all versions of netflow
e. netflow version 8

b.

22. After testing various dynamic IPv6 address assignment methods, an engineer decides that more control is needed when distributing addresses to clients. Which two advantages does DHCPv6 have over EUl-64 (Choose two.)
A. DHCPv6 requires less planning and configuration than EUl-64 requires.
B. DHCPv6 allows for additional parameters to be sent to the client, such as the domain name and DNS server.
C. DHCPv6 providers tighter control over the IPv6 addresses that are distributed to clients.
D. DHCPv6 does not require the configuration of prefix pools.
E. DHCPv6 does not require neighbor and router discovery on the network segment.
Answer: BC

23. Which tow commands must you configure in the calling router to support the PPPoE client? (Choose two)
a. peer default ip address pool
b. bba-group pppoe
c. mtu
d. pppoe enable group
e. pppoe-client dial-pool-number

e.

24. Router DHCP is configured to lease IPv4 and IPv6 addresses to clients on ALS1 and ALS2. Clients on ALS2 receive IPv4 and IPv6 addresses. Clients on ALS1 receive IPv4 addresses.
Which configuration on DSW1 allows clients on ALS1 to receive IPv6 addresses?
A. DSW1l (config-if)# ipv6 helper address 2002:404:404::404:404
B. DSW1 (config)#ipv6 route 2002:404:404::404:404/128 FastEthernet 1/0
C. DSW1 (dhcp-config)# default-router 2002:A04:A01::A04:A01
D. DSW1 (config)# ipv6 dhcp relay destination 2002:404:404::404:404 GigabitEthernet 1/2

Answer: C

25. Which three benefits does the Cisco Easy Virtual Network provide to an enterprise network? (Choose three.)
A. simplified Layer 3 network virtualization
B. improved shared services support
C. enhanced management, troubleshooting, and usability
D. reduced configuration and deployment time for dot1q trunking
E. increased network performance and throughput
F. decreased BGP neighbor configurations

Answer: A, B, C or BCD from chat igor’.

26. Which three items can you track when you use two time stamps with IP SLAs? (Choose three.)
A. delay
B. jitter
C. packet loss
D. load
E. throughput
F. path

Answer: A, B, C

27. Which two commands do you need to implement on a router to support pppoe client ?
A. peer default ip address pool
B. mtu
C. bba-group pppoe
D. pppoe enable group
E. pppoe-client dialer-pool-number
Aswers: B and E

28. Which two statements about NHRP in a DMVPN environment are true? (Choose two)
a. It requires each endpoint to have a unique network ID
b. It routes traffic through the tunnel
c. It can identify PIM-SM RPs over a tunnel
d. It can authenticate VPN endpoints
e. It provides address resolution to route traffic

answer: D and E

29. In which scenario can asymmetric routing occur?
a. active/active firewall setup
b. single path in and out of the network
c. active/standby firewall setup
d. redundant routers running VRRP

answer: D ?

30. After reviewing the EVN configuration, a network administrator notices that a predefined EVN, which is known as “vnet global” was configured. What is the purpose of this EVN?
A. It defines the routing scope for each particular EVN edge interface.
B. It aggregates and carries all dot1q tagged traffic.
C. It refers to the global routing context and corresponds to the default RIB.
D. It safeguards the virtual network that is preconfigured to avoid mismatched routing instances
Answer: C

31. Which CLI command can you enter to permit or deny IPv6 traffic travelling through an interface?
A. access-list
B. access-group
C. ipv6 access-class
D. ipv6 traffic-filter
Answer: D

32. A network engineer executes the show ip cache flow command. Which two types of information are displayed in the report that is generated? (Choose 2)
A. top talkers
B. flow export statistics
C. flow sample for specific protocols
D. MLS flow traffic
E. IP packet distribution
Answer: CE

33. A network engineer needs to verify IP SLA operations on an interface that shows on indication of excessive traffic. Which command should the engineer use to complete this action?
a. show frequency
b. show track
c. show reachability
d. show threshold

34. Which option is the minimum logging level that displays a log message when an ACL drops an incoming packet?
a. level 3
b. level 6
c. level 7
d. level 5

answer: b

34. Other than a working EIGRP configuration, which option must be the same on all routers for EIGRP authentication key role over to work correctly?
A. SMTP
B. SNMP
C. Passwords
D. Time
Answer: C

amm good luck mr BRAVO and thanks for sharing , you will pass next attemp
i think there are many false answer , plz you can used only its me updated by procyber .

@Procyber updated It’s Me (vce file).
updated It’s me vse files, now verion is 1.5 (446Q)
– deleted some repeat questions
– correct some questions a good format
– added answer explanation of new questions from digitaltut.com
Note: dump without LABs
https://drive.google.com/open?id=0B5ObM5nJeh3WZDlPMnUzWVpTRFk

@soso Thanks bro. Do you have pdf version? Can you share if you have))

Hi guys
Do someone have routing dump that still valid?? Could you send me please.

erkandursun1225 at gmail dot com

@bravo i checked and confirm the ans of 1-11 are okay but

Q12 . Which problem can be caused by latency on a UDP stream?
A. The device that sends the stream is forced to hold data in the buffer for a longer period of time.
B. The overall throughput of the stream is decreased.
C. The device that receives the stream is forced to hold data in the buffer for a longer period of time.
D. The devices at each end of the stream are forced to negotiate a smaller window size.

you mention answer B which is throughput that is wrong UDP have no effect on its throughput due to latency only TCP had as it is connection-oriented please see the ref to learn

1: http://blog.performancevision.com/eng/earl/links-between-latency-throughput-and-packet-loss

2:http://smutz.us/techtips/NetworkLatency.html

the only best option available is “C”

@ ciscotake

1 is incorrect correct is disable split horizon and subinterfaces
9 is incorrect the correct answ is server

@bravo

24. Router DHCP is configured to lease IPv4 and IPv6 addresses to clients on ALS1 and ALS2. Clients on ALS2 receive
IPv4 and IPv6 addresses. Clients on ALS1 receive IPv4 addresses.Which configuration on DSW1 allows clients on ALS1
to receive IPv6 addresses?
A. DSW1l (config-if)# ipv6 helper address 2002:404:404::404:404
B. DSW1 (config)#ipv6 route 2002:404:404::404:404/128 FastEthernet 1/0
C. DSW1 (dhcp-config)# default-router 2002:A04:A01::A04:A01
D. DSW1 (config)# ipv6 dhcp relay destination 2002:404:404::404:404 GigabitEthernet 1/2

Answer: C

wrong selection C the correct ans is “D”

please have a look on the link below and then find “ipv6 dhcp relay destination” to navigate the desired subject

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipv6/command/ipv6-cr-book/ipv6-i1.html#wp4145512431

@maximo

yes you are right I forget to mention Q1 but i did not pay attendion to Q9 but you point it… thank you bro

@maximo
yes your answers are correct
i think @bravo failed because the wrong answers provided by others dump , plz guys its me is the recomended dump here because all people discuss answer here and put the correct answer with the best explanations

CiscoTake
24. Router DHCP is configured to lease IPv4 and IPv6 addresses to clients on ALS1 and ALS2. Clients on ALS2 receive
IPv4 and IPv6 addresses. Clients on ALS1 receive IPv4 addresses.Which configuration on DSW1 allows clients on ALS1
to receive IPv6 addresses?
A. DSW1l (config-if)# ipv6 helper address 2002:404:404::404:404
B. DSW1 (config)#ipv6 route 2002:404:404::404:404/128 FastEthernet 1/0
C. DSW1 (dhcp-config)# default-router 2002:A04:A01::A04:A01
D. DSW1 (config)# ipv6 dhcp relay destination 2002:404:404::404:404 GigabitEthernet 1/2
plz correct the last option is
DSW1 (config-if)# ipv6 dhcp relay destination 2002:404:404::404:404 GigabitEthernet 1/2

For question 23, there were many option proposed here.

Which tow commands must you configure in the calling router to support the PPPoE client? (Choose two)

First need to figure out whether this question ask about how to configure a router as a PPPoE client or PPPoE server.

If PPPoE client then the answer will be
mtu
pppoe-client dial-pool-number

If PPPoE server then the answer will be
bba-group pppoe
pppoe enable group

Please share your thoughts.

Thanks guys. A lot of people on here try hard, but some would rather you did it for them.. unfortunetly it does require effort. I put 2 weeks of effort in.. but it only needed 1 however that was 8 hours study per day for 7 days a week.

@fiddy look through my previous threads from last 10 pages. I’m sure we covered them all BUT this is only personal opinion.. it’s very difficult to say which is correct for sure. My opinion my be incrorect.

GUYS remember the questions are only part of it.. If I was you I would put more effort in to varying the DnD questions & practice labs. Remember to use “?” Removing commands is almost impossible but I did figure out how to do it.

I.e. access-list 111 tcp any any eq www
To remove: no access-list 111 This would work.. but enter the full text may not. Hope this makes sense

@Ada – @CiscoDaddy
I have CBT Nugget for route and cisco live lessons is this what u need? I already passed the switch exam do you need switch lessons too?

Would thet be recent Ada? I’ve renewed my CCNP but I really would like to embed all concepts.

Thanks guys
C-D