Share your ROUTE v2.0 Experience

Hi guys,

please use link

https://www.mediafire.com/file/iz5cctgyhjt2qn1/ROUTE_Oct_2019.pdf

if you have the lastest dumps and tips for the exam please help i am writing end of jan

Roxannemoonsamy 1 @ gmail . com

Please help guys.

God bless

Which command is the correct way to summarize routes that were injected into OSPF area 100 from RIP?
A. redistribute rip metric 20 subnets
B. summary-address 172.32.64.0 255.255.224.0
C. area 100 range 172.32.64.0 255.255.224.0
D. ip summary-address 172.32.64.0 255.255.224.0

Can some body help me what is the answer
I belive the answer is C

QUESTION 279
What happens when unicast flood protection is triggered on a VLAN?
A. The VLAN is removed from the VLAN database
B. Traffic on the VLAN is passed to another VLAN with lower load
C. Traffic on the VLAN is load balanced across multiple links
D. The VLAN is shut down
Correct Answer: B

what is the right answer to this?

@ex Answer D

Which command is the correct way to summarize routes that were injected into OSPF area 100 from RIP?
A. redistribute rip metric 20 subnets
B. summary-address 172.32.64.0 255.255.224.0
C. area 100 range 172.32.64.0 255.255.224.0
D. ip summary-address 172.32.64.0 255.255.224.0
Can some body help me what is the answer
I belive the answer is C

C is wrong it is B ist correct.
On ASBR you use the summary-address and between Areas (on an ABR) you use area range command for summarization.
One tricky thing to mention the IP summary-address is used for the EIGRP summarization.

Which value determines the amount of traffic that a network path can hold in transit?
A. MSS
B. bandwidth delay product
C. route cache setting
D. maximum window size
Correct Answer: A

what is answer for this?

@ex I believe the correct answer is B. Bandwidth delay product

QUESTION 279
What happens when unicast flood protection is triggered on a VLAN?
A. The VLAN is removed from the VLAN database
B. Traffic on the VLAN is passed to another VLAN with lower load
C. Traffic on the VLAN is load balanced across multiple links
D. The VLAN is shut down
Correct Answer: D; not B

In short, this feature allows the switch to monitor the amount of unicast flooding per VLAN and take specified action if flooding exceeds specified amount. Actions can be to syslog, limit or shutdown VLAN – the syslog being the most useful for flood detection.

@MAD Thank you for the answer

aaaaaThe OSPF database of a router shows LSA types 1, 2, 7, and a type 3 default route only. Which type of area is this router connected to?
A. NSSA totally stub
B. stub area
C. totally stubby area
D. NSSA

The OSPF database of a router shows LSA types 1, 2, 7, and a type 3 default route only. Which type of area is this router connected to?
A. NSSA totally stub B. stub area C. totally stubby area D. NSSA
can some one answer me this question please.

@romail A

who buy this dumps?
Cisco 300-101 Certification Exam
I need it urgently

regards

@ex thank you very much

Which two facts must you take into account when you deploy PPPoE? (Choose two)

A. DDR idle timers must be configured to support VPDN login.
B. PPPoE supports a maximum of 10 clients per customer premises equipment
C. DDR is not supported
D. You must manually configure IP addresses on the PPPoE interface
E. An individual PVC can support one PPPoE client

what is correct answer?

Which two facts must you take into account when you deploy PPPoE? (Choose two)

A. DDR idle timers must be configured to support VPDN login.
B. PPPoE supports a maximum of 10 clients per customer premises equipment
C. DDR is not supported
D. You must manually configure IP addresses on the PPPoE interface
E. An individual PVC can support one PPPoE client

what is correct answer?

Hi guys. I passed my 300-101 exam last saturday jan 4.
850/1000, I studied all from premium membership in here.
no new questions, just the digitaltut listed in this site.
Sims: Ipv6 virtual link, OSPF eval, EIGRP eval and EIGRP stub.

Success for everyone!!!

@Anonymous @mahm_m

Which two facts must you take into account when you deploy PPPoE? (Choose two)

A. DDR idle timers must be configured to support VPDN login.
B. PPPoE supports a maximum of 10 clients per customer premises equipment
C. DDR is not supported
D. You must manually configure IP addresses on the PPPoE interface
E. An individual PVC can support one PPPoE client

correct asnwer is : B and E

I passed. 3 sims (EIGRP Eval, iPv6 Virtual-Link, OSPF Sim). I saw about 7 questions not in MPQ, NUQ Part 5 or NUQ Part 6. Everything else I saw came from the 3 listed locations. Sorry I don’t remember the any of the 7 new questions but studying the other questions provided here and doing the sims helps you to figure out the answers. Good Luck Everyone and thanks Digitaltut!!!

@Anonymous

Only the questions of MPQ NQU5 and NQU6 did you answer?

After about 40 days, Cisco will have major changes, and the exam will not be easy. Now is the best time to take the exam. Our questions and answers will help you pass the CCNA, CCNP and CCIE exams quickly during this time. Now is the last chance to pass the exam quickly. Free updates for one year. This is our website ↓↓↓
forums.delphiforums.com/happy2020/messages/1/1

Hi can anyone please send me the link for the dumps? I’ll do the exam next week and still jave TSHOOT to take. Kindly email me on chienchan0611 @ gmail. com

Using new backup router in spite of faulty one in OSPF domain but relationship with neighbor in one interface only not working, what is the reason of this problem? (Choose two)
A. area ID mismatch
B. authentication mismatch
C. process id of OSPF not match
D. OSPF timers not match

what is correct answer?

Which type of address does OSPFv3 use to form neighbor adjacencies and to send LSAs?
A. unicast IPv6 addresses
B. link-local addresses
C. multicast address FF02::5
D. unicast IPv4 addresses

what is correct answer ?

nan_m

Which type of address does OSPFv3 use to form neighbor adjacencies and to send LSAs?
A. unicast IPv6 addresses
B. link-local addresses
C. multicast address FF02::5
D. unicast IPv4 addresses

Anwer –> (B)

Link LSAs (Type 8)–Have local-link flooding scope and are never flooded beyond the link with which they are associated. Link LSAs provide the link-local address of the router to all other routers attached to the link, inform other routers attached to the link of a list of prefixes to associate with the link, and allow the router to assert a collection of Options bits to associate with the network LSA that will be originated for the link.

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_ospf/configuration/15-1sg/ip6-route-ospfv3.html

Which three characteristics are shared by subinterfaces and associated EVNs? (Choose three)
A. IP address
B. routing table
C. forwarding table
D. access control lists
E. NetFlow configuration

what is correct answer ?

@kha_ma

Correct answers are A, D and E.

Where to find GRE SIM ?

Share October 2019 dumps – grass green 28 @ gmail . com

Thanks

Please help!
In the IPv6 Ospf virtual link sim , do i have to put the below commands incase the loopback is not advertised. Did you people ping between R1 and R4. Please help

After finishing the configuration don’t forget to ping between R1 and R4 to make sure they work well!

Now all the configuration was done. But we still cannot ping the IPv6 loopback interface of R4 from R1 because the IPv6 loopback interface of R4 has not been advertised into OSPFv3. But we can check by using the command show ipv6 route on R1. If you can see the IPv6 loopback interface of R4 then you don’t need to do anything else.

But in real routers, we have to advertise the IPv6 loopback interfaces of R1 & R4 into OSPFv3 to make them appear in the routing tables with the following commands:

R4(config)#int loopback 0
R4(config-if)#ipv6 ospf 1 area 54

R1(config)#int loopback 0
R1(config-if)#ipv6 ospf 1 area 0

NB: For people who wrote the exam ,please help

Which feature can automatically assign IP addresses in a PPPoE environment.?
A. DHCP
B. BOOTP
C. PPP
D. APPA
Correct Answer: C

any idea?

Did the ping between R1 and R4 work? Please help.

Am following the premium answers

good point Eng.Cisco anyone who did the ipv6 ospf virtual link sim did they need to add or did ping work without:

R4(config)#int loopback 0
R4(config-if)#ipv6 ospf 1 area 54

R1(config)#int loopback 0
R1(config-if)#ipv6 ospf 1 area 0

A router in an EVN environment is choosing a route. Which value is given the highest selection priority?
A. default administrative distance of the route
B. IGP administrative distance of the route
C. lexical value of the source VRF name
D. VNET tag of the route
E. replication status of the route
Correct Answer: C

isnt it B?

Please help: For the ones who wrote the exam.
Am not able to practise on GNS3 because of images. I have errors.

Question is; The OSPF Sim.
Did you use the exact commands as in premium please?

Please , someone put the correct commands/configurations used for OSPF Sim in exam

@burns @Eng.Cisco
For the IPv6 OSFP virtual link in GNS3 I did use that loopback config and am able to ping R1 from R4.
R1#show running-config interface loopback 1
interface Loopback1
no ip address
ipv6 address FEC0:11::1/64
ipv6 ospf 1 area 0
R4#show running-config interface loopback 1
interface Loopback1
no ip address
ipv6 address FEC0:44::4/64
ipv6 ospf 1 area 54
R4#ping ipv6 FEC0:11::1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0:11::1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5)

Remove and no longer can ping.
R1(config)#interface loopback 1
R1(config-if)#no ipv6 ospf 1 area 0
R1(config-if)#end

R4#ping ipv6 FEC0:11::1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0:11::1, timeout is 2 seconds:
…..
Success rate is 0 percent (0/5)

Add back and ping works
R1(config)#interface loopback 1
R1(config-if)#ipv6 ospf 1 area 0
R1(config-if)#end
R4#ping ipv6 FEC0:11::1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0:11::1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5)

Correct answers are A B C

“trunk interface can carry traffic for multiple EVNs. To simplify the configuration process, all the subinterfaces and associated EVNs have the same IP address assigned. In other words, the trunk interface is identified by the same IP address in different EVN contexts.
This is accomplished as a result of each EVN having a unique routing and forwarding table, thereby enabling support for overlapping IP addresses across multiple EVNs.”
http://www.cisco.com/en/US/docs/ios-xml/ios/evn/configuration/xe-3sg/evn-overview.pdf

@Switch, so you didnt need to configure the below commands

R4(config)#int loopback 0
R4(config-if)#ipv6 ospf 1 area 54

R1(config)#int loopback 0
R1(config-if)#ipv6 ospf 1 area 0

@Switch @Eng.cisco

I downloaded all Sims and recreate them using the latest GNS3 version, once you download the files you can see the router configuration with notepad++, and load it to the routers easily, I found an image for C3725 that works perfectly.

I did the OSPF virtual link and I needed to add the loopback interface to the OSPF, this is using GNS3, I am not sure if on the exam simulation is needed or not, what i will do is try to ping if work cool if not i will add the ipv6 ospf X to each loopback interface.

I found the IOS here: https://srijit.com/working-cisco-ios-gns3/ is not IOS15v but it work, oyu could use router C7200 and it has IOS15v,

keep practicing and understanding the concept.

anyone that already took the exam? any advise?, next week is my test day

Does anyone has the latest valid dump that could send to me pleas?

Hi, I’ve used this website to try and pass the Route but I only got 739 points and needed 760. I am not sure where I went wrong but many of the questions were not in the popular questions area. I think it might have been because I did not look at the new updated questions, I have now looked at these and I have my next exam booked in 1 week. Please could someone advise which drag and drop questions to master. Popular questions show 20 but another section only 13. Thanks everyone and Good Luck. All the lab questions were here and very good.

@Eng. Cisco No need to ping the R4’s loopback from R1. Anyway, in the real exam ping won’t work. Including “wr” and “copy run start”. As long as you can see the R4’s loopback then your GOLD!

@route
I think you may be incorrect there the question mentions you know its correct when you can see in show ipv6 route and your able to ping the loopback

@route,

I agree with @burns, because to see R4 Loopcback on R1 routing table you need to advertise the loopback into OSPF, if not you will never see that route injected into ospf. just go to the GNS3 and fix the virtual-link and with only that R1 still do not see R4 loopback, so the only way to see the loopback injected into R01 routing table is when you advertise it. and after that you will beed to advertise R01 loopback as well so your ping be successful.

Passed today with 8xx
What I can advise is to study the whole document, I was reading only most popular Q and newly updated and it lead me to fail 2 times. Simulations were EIGRP eval + OSPF virtual link + OSPF, I had a lot of drag and drops and all of them were in dumps. Don’t buy expensive dumps from other sites, these are fine, but you have to study them all. Good luck!

Congrats @Kitty.

please dump viled des 2019 (gadorashaker)(@)(gamil)(.com) thenks my dears

I passed the exam today 9xx/1000.

Labs: EIGRP SIM, OSPF SIM, OSPFv6 Virtual-link
D&D: IPv6, NAT

Study DHCP options, they ask about option for static route on DHCP. SNMPv3.

@me

was eigrp the eval one?