Share your ROUTE v2.0 Experience

i saw this question on page 369 what do you think?

4.A network engineer is enabling RIPng on a new customer link. Under which configuration
mode is RIPng enabled?
A. Global
B. Router
C. Interface
D. IPv6

I think C
xample:Device(config-if)# ipv6 rip process1
“enableEnables the specified IPv6 RIP routing process on an interface:

=
=
=
=
= Is there anyone who wrote the exam today?
= what were the Sim’s?

What command would you use to set EIGRP routes to be prioritized?
A. distance 100
B. distance 89
C. distance eigrp 100
D. distance eigrp 89

Answer: D

inst it B??

The excerpt was taken from the routing table of router SATX. Which option ensures that routes from 51.51.51.1 are preferred over routes from 52.52.52.2?
A. SATX(config-router)#distance 90 51.51.51.1 0.0.0.0
B. SATX(config-router)#distance 89.52.52.52.2 0.0.0.0
C. SATX(config-router)#distance 90.52.52.52.2 0.0.0.0
D. SATX(config-router)#administrative distance 91 51.51.51 0.0.0.0
E. SATX(config-router)#distance 89 51.51.51.1 0.0.0.0 F. SATX(config-router)#administrative distance 91 52.52.52.2 0.0.0.0

what is the right answer to this??

Which of the below mentioned conditions form a neighbor relation in EIGRP?(Choose three)
A. Hello or ACK received
B. AS number match
C. Hello timer match
D. Identical metric (k values)
E. Dead Timer Match
F. Network Time Match

Answer: A B D

sint it BCE??

@exec
regards to setting AD the question asks for a route you can check this by opening a router and try enabling eigrp with (router eigrp 1)

R1(config-router)#distance eigrp ?
Distance for internal routes

R1(config-router)#distance ?
Administrative distance
eigrp IP-EIGRP distance

so the answe is D. distance eigrp 89 both are incomplete if hitting enter though.

E. SATX(config-router)#distance 89 51.51.51.1 0.0.0.0 is the only correct answer for the next question and its a complete comand

ABD is the corect answer for the last question you ask
A. Hello or ACK received
B. AS number match
D. Identical metric (k values)

Happy new year! May all pass your CCNP EXAM

hi guys please share latest dumps im taking the exam soon please send to Ntombizodwa dot nunu at gmail dot com

@anonymous

Yes distance eigrp 89 is part of a comand that changes the eigrp routes globally you have to finish the comand with an external route priority also so by default an eigrp priority is 90 and external 170 but eigrp sumary routes are 5

@anonymous kindly share latest dumps to ntombizodwa dot nunu at gmail dot com

@thuli
go to ROUTE FAQs & Tips on right
there is a section towards the end that talks about “why am i unable to see questions” click this and download the latest pdf

I thought my score was passing but it looks like I was little off and did not pass , and will have to retake. Any new questions added in the new year?

@erman

how much you score , did you not read when it says pass or fail .. are you same person who had test on 25th …what were your question and if you really fail then what went wrong you think

Hi,

Could you plz tell me where can I found CCIE 400-101 dump?

@burns thank you

passed the exam with a great score ,

my tip is to know all topics because i met something like 10 new questions ,
for dumping i think digitaltut do a great job most of the questions from here ,
labs was : eigrp evaluation , ipv6 virtual link , eigrp stub ( make sure you save the config).
thats what i remember from the new questions :

– a question about ospf : if area-range or summary-address are assinged in the ABR or ASBR to summary between ospf areas.

-a question about redistribute only IBGP to ospf somthing like redisribute bgp internal-___

-protocols affected by MPP (the answers from this site were not presented in my tests), I chose the Telnet and HTTPS.

a few more questions that i dont remember :( sorry and luck.

@NetBrain

was the sims identical to here?

@ Netbrian

– a question about ospf : if area-range or summary-address are assinged in the ABR or ASBR to summary between ospf areas.

Can you please remind yourself actual question and what were options and what was right answer ..
Please try to remind yourself more questions

@netbrain
was it:
you want the device on your network to summarize routes between ospf and different autonomous systems. which action must you take:

Configure the summary-address command on the ASBR
Configure the summary-address command on the ABR
config the area range command on the ABR
config the area range command on the ABBR

think the answer is
Configure the summary-address command on the ASBR

For the labs in the exam are these shorthand commands allowed instead of using just show running-config and searching. Also, need to ask again if anyone has a vce file for the Oct pdf?

switch010101 at gmail com

show running-config | in bandwidth
show running-config interface fastEthernet 0/0
show running-config | sec router eigrp
show key chain
show interfaces summary

@switch you can use help ? and tab in exam i did in switch exam

@A Ok thanks but was hoping they don’t make you search through the running-config since that is not what working professionals would be doing unless troubleshooting an issue.

@switch
You can also use show run it’s exactly like a real router

anyone else struggling to retain the information i find the route tag questions really tricky i have tried remembering the order i know the subject just the question is really tricky.

Please!

I’m writing the exam tommorow. Which questions i need to focus on?

Sims?

A packet capture indicates that the router is not forwarding the DHCP packets that it receives on interface FastEthernet0/0. Which command needs to be entered in global configuration mode to resolve this issue?
A. ip helper-address B. ip DHCP relay C. service DHCP D. ip forward-protocol

Answer: B

what is the right answer to this?

Passed with 8XX. A lot of DHCP questions, A LOT. It’s absurd. No BGP questions. This exam should focus more on routing than DHCP

@Anoymous whats are the sims?

@S
Yes I was thinking show run works per norm but am hoping it is like a real router where those shorthand commands can be used to speed things up when searching. Cisco likes to disable things that would be used in your job (grrr) so wanted to make sure from those who have taken the exam and maybe tried to use some of those or any variation of those like using the | , checking the show run on an interface directly, interface summary and key chain.

Which two statements about redistributing EIGRP into OSPF are true? (Choose two)

A. The redistributed EIGRP routes appear as type 3 LSAs in the OSPF database
B. The redistributed EIGRP routes appear as type 5 LSAs in the OSPF database
C. The administrative distance of the redistributed routes is 170
D. The redistributed EIGRP routes appear as OSPF external type 1
E. The redistributed EIGRP routes as placed into an OSPF area whose area ID matches the EIGRP autonomous system number
F. The redistributed EIGRP routes appear as OSPF external type 2 routes in the routing table

Answer: B F

Why not C , the AD of external eigrp routes is 170 ?

Hi,

The new questions is related to what topic?

hi guys i bought prepaway dumps however i dont afford to pay for the vce please share if you have i will share the dumps (ete file for windows )

@Kikimora

EIGRP external routes have a AD of 90 internal 170 external but when it hits ospf it goes to an E2 which is 110 with a metric cost of 20.

For the labs when copy run star is not posible, do we just leave it unsaved?

@thuli can you send men dump ? hikmetcisco @ gmail dot com

I wrote the exam today. And passed the exam.
.
.
3 labs ospf sim, eigrp evalution, new sim to configure ospf (never seen before).
.
.
. I get about 6 D & D (mgre, framerelay, keepalive…..
And about 10 new questions i never seen. I will answer your questions. Ask me.

@Le do you remember the 10 new questions? thanks

@Le did you see new LAb ospf question ? can you explain?

@ Le can you please explain how was the new Lab

I cant remeber guys. Once i remeber i will put them here. The new lab is to adverstise ospf id 83 network between two routers. Once configured correctly, But focus more on D& D they just f**king give in randomly

Please study all the sim’s as much as possible. Because they give randomly. I havent seen any bgp questions and got dhcpv6 questions such as two way messages (solicited, reply).

And i got the diagram block dhcp message ( cant remember the question) such as three layer architecture. (Acl to deny or permit)

@Le , many thanks

And i got the diagram block dhcp message ( cant remember the question) such as three layer architecture. (Acl to deny or permit)

And
+Ospf sim ( configure area with stub and totally stubby)
+New ospf sim to configure ospf between two router ( you need to advertise the network in two routers…. It is easy.. find the network id because both interface are configured with ip addresses.)

+ Eigrp evaluation sim

Mpp & cpp D&D
Framerelay D&D
Dmvpn (mgre, nhrp, ……D&D

+ can remember there was a question on TNC. (it is on the dump)
+ Which typea of lsa exist on stub (lsa 1,2,3) (it is on the dump)
+
+

I’m on the way to home. I will get home and put all the questions that exist on the exam. Once i see the dump, I may get remember the questions

@Le can you send men dump? which one you prepare for exam hikmetcisco @ gmail dot com

@Lee

Can you please give more information about new sim .. and what you did and what config to apply .. wast that difficult

Another question i got
* Which two debug command can you use to view issues with chap & pap
– debug ppp negotiation ( they gave a “debug aaa negotiation” which is not correct)
– debug ppp authentication

*Which issue is importatnt to address when intergrating to address when intergrating two networks with different routing protocols
– preventing asymmetric routing

* which two protols can be affected by Mpp?
– Http
– ssh

* Obtain a global unicast ipv6 address autoconfig (exist on dump)
– router adverstiment

* Which two statment indicate a valid association mode for ntp synchr..
– the client listern to ntp broadcast
– the client ntp server for time

* And the questions with ip sla that the aswer with
– delay
– jitter
– packet loss

Configruration on new sim there are three routers interconnected each other. We need to configure only two routers which is on area 14)
.
they told to include process id as 83
.
R1 (config) router ospf 83
R1 (config) network 152.168.5.4 0.0.0.3 area 14

On router two

R2 (config) router ospf 83
R2 config) network 152.168.5.4 0.0.0.3 area 14

Thats all bro. Make sure other routues have learned by R1
. And run copy run config

For now. Bye. I will upload all the dumps and books used in the exam. Thank you digital tut 😘