Share your ROUTE v2.0 Experience

@Sean George
What does EVANs mean?

The stub device responds to all queries for summaries, connected routes, redistributed static routes, external routes, and internal routes with the message “inaccessible.

@route-quest – thanks for answering my question for eigrp-stub question

passed exam all drag drops from july dumps mostly about AAA, about 12 new questions which i didnt see in MPQ and NU 5 and 6, may be they are from old questions but im not sure, labs i only got 3 OSPF Evaluation, EIGRP redistribute and Policy based routing. DigitalTUT is enough to pass this exam thanks all Troubleshooting is next for me.

@ ME congrats. What is the meaning of NU5 and NU6?

@Sly, Newly Updated Questions part 5 and 6.

which type of access list allows granular session filtering for upper-level protocols?
A. content-based access lists
B. context-based access lists
C. reflexive access lists
D. extended access lists

C or D ?

Got two different answers from diff sources. your thoughts?

HI,
@route-guest
answer is C. Reflexive access list.
Reflexive Access Lists
Reflexive access lists provide filtering on upper-layer IP protocol sessions. They contain temporary entries that are automatically created when a new IP session begins. They are nested within extended, named IP access lists that are applied to an interface. Reflexive access lists are typically configured on border routers, which pass traffic between an internal and external network. These are often firewall routers. Reflexive access lists do not end with an implicit deny statement because they are nested within an access list and the subsequent statements need to be examined.

Thanks gregory28

hi can any one confirm if answer B is still correct. The OSPF timer values of R1-R3 link were 30, 120, 120

Question 2

Check the serial links connected to R3. Which statements are correct?
A. The neighbor command must be used on R1-R3 link to keep the adjacency up
B. The OSPF timer values of R2-R3 link are 30, 120, 120
C. The OSPF timer values of R1-R3 link should be 10,40,40
D. R3 must flood LSUs to all the routers on the network.

when I check show int s1/0 and s1/1 i got the following:

The OSPF timer values of R1-R3 link were 30, 120, 120
The OSPF timer values of R2-R3 link were be 10,40,40

if some one could explain the correct answer. Thanks

hi can any one confirm if answer B is still correct. The OSPF timer values of R1-R3 link were 30, 120, 120

Question 2

Check the serial links connected to R3. Which statements are correct?
A. The neighbor command must be used on R1-R3 link to keep the adjacency up
B. The OSPF timer values of R2-R3 link are 30, 120, 120
C. The OSPF timer values of R1-R3 link should be 10,40,40
D. R3 must flood LSUs to all the routers on the network.

when I check show int s1/0 and s1/1 i got the following:

The OSPF timer values of R1-R3 link were 30, 120, 120
The OSPF timer values of R2-R3 link were be 10,40,40

if some one could explain the correct answer. Thanks

Hi
@mark, ben

answer is B

I simulate the lab in gns3 and this is the answer. Non-broadcast Network (Default timers are Hello 30 secs, Dead 120 secs).
The correct answer is: Timer intervals configured, Hello 30, Dead 120, Wait 120

Internet Address 192.168.23.3/24, Area 0, Attached via Network Statement
Process ID 1, Router ID 3.3.3.3, Network Type NON_BROADCAST, Cost: 64
Topology-MTID Cost Disabled Shutdown Topology Name
0 64 no no Base
Transmit Delay is 1 sec, State DR, Priority 1
Designated Router (ID) 3.3.3.3, Interface address 192.168.23.3
Backup Designated router (ID) 2.2.2.2, Interface address 192.168.23.2
Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5

The enterprise network WAN link has been receiving several denial of service attacks from both IPv4 and IPv6 sources. Which three elements can you use to identify an IPv6 packet via its header, in order to filter future attacks? (Choose three)
A. Traffic Class
B. Source address
C. Flow Label
D. Hop Limit
E. Destination Address
F. Fragment Offset

A C D or B C E ???

Gents,
Lets not confuse ourselves. Digital tut answer is different to the one you get in the exam.
Digital tut version is straight forward as you can see the timer values matching.

Check the serial links connected to R3. Which statements are correct?
A. The neighbor command must be used on R1-R3 link to keep the adjacency up
B. The OSPF timer values of R2-R3 link are 30, 120, 120
C. The OSPF timer values of R1-R3 link should be 10,40,40
D. R3 must flood LSUs to all the routers on the network.

If you do ” show ip ospf int s1/0 and s1/1″ both have the opposite timer values.
As someone explained since the network type for R1-R3 is non-broadcast, the neigbhor command must be entered. hence the correct answer is A.

@Prabhu
Answer is A,C,D. ( I know there are two diff set of answers but i this one makes sense since its a ipv6 packet.)

passed exam today it was very easy .All Things what you Need is on this Website (digitaltut).

please do not learn only the MPQ and Update 5 ,6.Learn the whole Questions .

I wish you all best.

@target CCIE is the July Dump valid again? were there any new questions?
If you remember the new ones can you please tell what where they?

@Toni ,no new Questions .The command copy to start doesnt work.Learn the whole Questions and it will work .

Dear Team,

Do you have latest dump for CCNP route 300-101?

Please kindly share to me.

Br,

@ target CCIE ,which LAB’s came out on the CCNP Route exam ?

Dear Team,

I pass exam today.8xx.
thanks july and everyone for the help!

Best regards,

passing CCNP switch today with score 901 using 591lab dump (349qs)
if you want it just send me mail to zayed.ibrahim at yandex dot com

Dear Team,

please tell me which site to prepare for the next switch 300-115 exam ?
….tut.com ?
best Regards

Hi
@zayed00

Please tell me site for CCNP switch (300-115) similar with digitaltut ?

@Anonymous,

Source Address, Flow Label and Destination Address (had this one in my exam)

Same Beaf

Dear Team,

Who wants to take the exam should study all the information on this site.
it is enough to pass the exam !

good luck !

any body has just apply the exam please… is july dump is enough to pass ????

Passed the exam.

Labs: PBR/OSPF-EIGRP Redistribution/OSPF Eval.

D&D: AAA, uRPF, BGP states.

Lots of EVN-VRF questions (Like 12 or 15)

Like 2 or 3 new questions I did not see here.

The vast majority of questions can be found in MPQ, NUQ5 and NUQ6. Also from July version.

Good luck!

Hello Anybody,

Who have MPQ? Please send to me.

Br,

What does “EVN questions” mean?

I just passed today the exam. everything is in the site and the july dump is still valid. for the labs you need to make a ping and do a traceroute to check the route traffic.

CAN SOMEONE GIVE ME THE QUESTIONS????
tHANKS

J o t a l o p z @ h o t m a i l . c o m

HI,

Guys from where i can download the July dumps file ??

Thanks

Hi all:

Today I passed my exam:

LAbs:
EIGRP OSPF Redistribution Sim
policy Policy Based Routing Sim
ospf evaluation sim (the first question is different)
Check the serial links connected to R3. Which statements are correct?
A. The neighbor command must be used on R1-R3 link to keep the adjacency up (I selected A)
B. The OSPF timer valuess of R2-R3 link are 30, 120, 120
C. The OSPF timer values of R1-R3 link should be 10,40,40
D. R3 must flood LSUs to all the routers on the network.
Drag and Drop
Excessive unicast flooding condition: caused by including a host port in STP
Out-of-order packets: potential result of disabling FIFO
TCP starvation: potential effect of excessive UDP traffic on link
Asymmetric routing: cause of inconsistent traffic patterns
Latency: condition in which packets require an excessive length of time to traverse a switch

+ if authenticated – It allows the user to perform the requested function once authenticated
+ none – It instructs the network access server to proceed without requesting authorization
information
+ local – It provides authorization for a limited set of functions only
+ krb5-instance – It uses a defined instance for authorization
+ group radius – It uses authorization information from a standards based server
+ group tacas+ – It uses authorization information stored as attribute value pair in a Cisco
proprietary server

+ Authentication: challenge and response operation
+ Accounting: feature that logs network usage
+ TACACS+: authentication method that uses TCP
+ RADIUS: authentication method that uses UDP
+ Authorization: controls specific access privileges of a user

and other about AAA

I studied july_PDF and the questions are similars

Thanks for share information.

@anyone,

Thanks for ur sharing Fri.

Hi all
Failed ccnp route exam yesterday 762, due to my own error and lack of understanding. The ospf/redistribution scenario threw me off and the nerves got to me. can anyone comment on what the description of the scenario they got for this Lab please. Some thing about two companies merging, was that correct.

Been studying hard and using this site as a top up. I have been learning and trying not to just memorize, INE, Press books and INE rack rentl

Time to re-book, study and go again

@Ben I think we are on the same boat. I too lost marks on that sim because i wasn’t able to ping from R1 to R4 inspite of adding the redis commands.nerves too got on to me and I just forgot to apply the distance command and left the sim and failed by few points. I know its frustrating but just re-book it and good luck!. I think the sim is exactly the same we have here on this site. The only diff was the link between R1 and R2 was fastethernet but that shouldn’t change the output.

Can anyone tell me what “digitaltut” is?

@route-quest when you get fastethernet instead of serial ..that mean the traffic will go from the fast ethernet ,so we must change the admenstrative distance to some thing smaller than the connected ospf because connected ospf will redistribute to eigrp with 110 so,you should choose something little than this value under eigrp process ,i.e distance eigrp 90 101 the second value must be less than 110

Thanks for your response route-quest, yeah sounds like I did the same. Can you remember how the scenario was explained in the first sentence. I am re booking next week

Please send me the Chinese dump(july) {email not allowed} i cant fount it

please share chinese dump

Can anybody share the Chinese dump link other than that Chinese link…..couldn’t get it from there

ospf evaluation sim

Can anybody confirm if the answer for below question is A or B ??

Check the serial links connected to R3. Which statements are correct?
A. The neighbor command must be used on R1-R3 link to keep the adjacency up
B. The OSPF timer valuess of R2-R3 link are 30, 120, 120
C. The OSPF timer values of R1-R3 link should be 10,40,40
D. R3 must flood LSUs to all the routers on the network.

@ben

The network requirements state that you must be able to ping and telnet from loopback 101 on R1 to the OPSF domain test address of 172.16.1.100. All traffic must use the shortest path that provides the greatest bandwidth. The redundant paths from the OSPF network to the EIGRP network must be available in case of a link failure. No static or default routing is allowed in either network.
A previous network engineer has started the merger implementation and has successfully assigned and verified all IP addressing and basic IGP routing. You have been tasked with completing the implementation and ensuring that the network requirements are met. You may not remove or change any of the configuration commands currently on any of the routers. You may add new commands or change default values.

Here are the stuff you are looking for !!!
ht***tp***:/***/ww***w.medi***afire.c***om/file/o6kvpeim2urphid/CCNP_2019-08-08.rar
**Remove

ospf evaluation sim

Can anybody confirm if the answer for below question is A or B ??

Check the serial links connected to R3. Which statements are correct?
A. The neighbor commandq must be used on R1-R3 link to keep the adjacency up
B. The OSPF timer valuess of R2-R3 link are 30, 120, 120
C. The OSPF timer values of R1-R3 link should be 10,40,40
D. R3 must flood LSUs to all the routers on the network.

What is wrong with answer B?
When you do show ip ospf interfaces and check connections to R3 and see the below values that mean B is th correct answer.

Serial1/0 is up, line protocol is up
Internet Address 192.168.23.3/24, Area 0
Process ID 1, cID 3.3.3.3, Network Type NON_BROADCAST, Cost: 64
Transmit Delay is 1 sec, State WAITING, Priority 1
No designated router on this network
No backup designated router on this network
Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5

Also when a connection between 2 routers is a point to point and the OSPF defined as point to point, it has to be NON_BROADCAST. It cannot be broadcast. Your below comment is wrong :
“B can’t be true unless R1-R3 link was point-to-point/Broadcast “

@Nik

We are discussing Ahmed Exam version not Digital version:

on Ahmed Exam version : answer B is about R2-R3 not R1-R3.

When he ran show int >>> he found R2-R3 timers were 10 40 40 . which doesn’t meet option B .

########################################

Ahmed Exam Version

#############################################

Check the serial links connected to R3. Which statements are correct?
A. The neighbor command must be used on R1-R3 link to keep the adjacency up
B. The OSPF timescar values of R2-R3 link are 30, 120, 120
C. The OSPF timer values of R1-R3 link should be 10,40,40
D. R3 must flood LSUs to all the routers on the network.
we
when I check show int s1/0 and s1/1 i got the following:

The OSPF timer values of R1-R3 link were 30, 120, 120
The OSPF timer values of R2-R3 link were be 10,40,40

########################################################

Please be careful , there is 3 versions of this question at Cisco pool to my knowledge.

Digitaltut only has one case . which is the one you were referring to .

I hope this was informative and helpful.

Good Luck .

Dear @passed

could you please send me the latest dump : a-z-g-33 @ hotmail . com

thanks

Consider this scenario. TCP traffic is blocked on port 547 between a DHCPv6 relay agent and a DHCPv6 server that is configured for prefix delegation. Which two outcomes will result when the relay agent is rebooted? (Choose two)

A. Routers will not obtain DHCPv6 prefixes.
B. DHCPv6 clients will be unreachable.
C. Hosts will not obtain DHCPv6 addresses.
D. The DHCPv6 relay agent will resume distributing addresses.
E. DHCPv6 address conflicts will occur on downstream clients.
Answer: A D ??

The explanation for A as an answer is that Relay agent uses port 547 between itself and the Server to forward and respond to messages and since traffic is blocked on port 547 then routers will not obtain DHCPv6 prefixes. However, the question states that there is a TCP block on port 547 and the relay agent only uses UDP. Hence there is no impact on the operation of the DHCP Server and relay agent at all. As such Answer D is correct and the relay agent still keeps distributing addresses and forwarding requests. The prefix delegation will continue to function and the Server still has all its bindings and leases. Maybe the leases expire while the relay agent is down? If you consider that then D and E are probably the best answer here. A as an answer is definitely incorrect because there is no impact on the operation.

I’ve actually lab this exact scenario and was expecting that A was correct until I saw DHCP requests on port 547 going backwards and forwards to the server and then suddenly realised that its UDP and not TCP.

I’d say the answer here is D and E. Any one want the lab in GNS3 let me know.