Share your ROUTE v2.0 Experience

@ssuet@2013

“suppress” means put an end to something by force.
So EIGRP is the correct answer. because this is an Cisco Exam and EIGRP is Cisco Systems proprietary protocol :)

EIGRP LAB/Case means EIGRP Evaluation Simulator
@ Helaya & Nik thanks for the reply.
what is this suppresses means and what this questions means ?

@ Nik i have put Q2 answer as B but its wrong… when you so sh ip ospf int s0/1 or s1/2 etc

@Ahmed

5 Questions of Eigrp Evaluation is exactly same as this website or there was something new in it?
Please reply I have exam tomorrow.

Hi guys, do you have some IOS for lab address family ipv6 ?

@Ahmed
If it is exactly the same as EIGRP lab here, answer B is correct.
How do you know your answer as “B” was wrong? In the real exam, you don’t see the answers.

Are you just using the July Dump to prepare for the test?

hello guys,

Anyone has latest VCE player?

WTF is the answer of this question

which protocol suppresses the incomming and outgoing routing advertisement in the routing table when pasive interface is configured on the interface..

BGP
RIPv2
OSPF
EIGRP

WTF is answer to this question …any one please ???????

Question 2

Check the serial links connected to R3. Which statements are correct?
A. The neighbor command must be used on R1-R3 link to keep the adjacency up
B. The OSPF timer values of R2-R3 link are 30, 120, 120
C. The OSPF timer values of R1-R3 link should be 10,40,40
D. R3 must flood LSUs to all the routers on the network.

when I check show int s1/0 and s1/1 i got the following:

The OSPF timer values of R1-R3 link were 30, 120, 120
The OSPF timer values of R2-R3 link were be 10,40,40

WTF should i answer this ????

I answer B. The OSPF timer values of R2-R3 link are 30, 120, 120 as per this website…tell me should i did right ?

4 Drag and Drop FYI: UNdwICAST,ACL, AAA, AAA commands ,AAA features.
Labs: eigrp case, route-map REDISTRUIBUTE , OSPF case

There were so many questions of IP SLA and AAA which are NOT on this website.

Hi guys, can you share exams labs please ?

Hi Guys,

Can you confirm July PDF is enough to pass the exam?

Really appreciate it

Who is ‘Anonymous’ who is copying my questions and comments and pasting again ???

@Nik how come answer is B
Answer B is B. The OSPF timer values of R2-R3 link are 30, 120, 120.

But when you check in real lab it was comming 10,40,40. read my post again.

But still I click on Answer B

@anonymous the correct answer to OSPF eval sim depends upon what exactly is represented in the output to the command in the architecture that is shown and your understanding. Its so very easy to change simple config and have the responses change.

To assist, what was the OSPF network types on the serial interfaces present on R3? a sh ip ospf int sx/x will identify the network type. broadcast and pop interfaces should have timers of 10, 40, 40 and those that are NBMA should be 30, 120, 120. Typically one interface is NMBA and one interface is PTP. The right answer depends upon the understanding of the network types.

Also, the answer to the neighbour command being required is dependent on the network types as well and if you actually have an adjacency present. sh ip ospf neigh should help to inform you if their is an adjacency present or not.

Is R3 the ABR and is it a DR for all area’s and responsible for flooding?

The answer to the question changes at times it is not a static sim but dependent upon understanding.

With regards to the IP SLA and AAA questions are you referring to the August pdf that the questions are not listed or just the questions down the right hand side of the page?

@ahmed

WTF is the answer of this question
which protocol suppresses the incomming and outgoing routing advertisement in the routing table when pasive interface is configured on the interface..
BGP
RIPv2
OSPF
EIGRP

I’m not sure I’d be interested in views.

Ripv2 passive-interface stops sending multicast updates but does not stop receiving multicast updates.

EIGRP and OSPF passive interface stops sending multicast hellos hence stopping creating of adjacencies with neighbours meaning that there are no incoming/outgoing routing updates.

where I can have August PDF please ?

Passed– With a very very close margin.

9-10 New questions. NUQ5 NUQ6 MPQ is valid but not enough to pass. You have to study every topic in digitaltut with their respective questionss.

3 D&D valid.

Labs
PBR (ip change)
Redistribution (IP change)
OSPF ( question 2 is change now right choice is we have to use neighbor command to keep adjacency up)

Digitaltut membership worth every penny.

OFF to switch now.

Hi ssuet@2013

Can you let me know the new questions please?

Really appreciate it

Hi All,
Is there an explaination on the OSPF Evaluation sim for Question3 ie how old is the type LSA from router 3 for area 1 ? What commands are we supposed to implement to find out the Type4 LSA.I am an premium member and haven’t found any explaination on the website.
Any help would be appreciated.
Thanks.

I failed in the PBR exam. it seem the sabe with the ip changed but when i send the http packets it just say 9 packets http sent. Please Help!

Hi,

Was the questions the same from July PDF

@lebron curry
Did you not do a ‘show route-map’ and check that you had packets matching?
How do you know that you failed the exam because of that lab?

For the lab sims on the exam, do we type the commands in, or is it multiple choice? I do not really understand the format for the labs on the exam.

@Route-quest

sh ip ospf database

Type 4 LSA are ABR created due to an ASBR being in the area or more to the point the area being defined as a NSSA. When an area is NSSA the ABR send a type 1 LSA into the adjacent area with the p bit set. The next ABR then turn that into a Type 7 LSA. Or more to the point the NSSA area ABR is a pseduo ASBR. The question is poor but th answer depnds upon which aea you look at to depend if you get a type 4. If you look at the area between R3/4 (sorry can not remember the number) you will see a Type 4 present that is the result of the NSSA area.Typically on the question that is provided the actual answer is that one area is a NSSA and hence by definition has no type 4 lsa. The other is a Totally Stubby area which has no type 3 or 4. Of course if you have no type 4 there is no need for a type 5 either. So technically the question is incorrect and there is no type 4. The answer given is relaly the type 3 from router 3 to router 4 age from sh ip ospf database.

Hope that helps.

@Ahmed
@Aanonymous

Check the serial links connected to R3. Which statements are correct?
A. The neighbor command must be used on R1-R3 link to keep the adjacency up
B. The OSPF timer values of R2-R3 link are 30, 120, 120
C. The OSPF timer values of R1-R3 link should be 10,40,40
D. R3 must flood LSUs to all the routers on the network.
we
when I check show int s1/0 and s1/1 i got the following:

The OSPF timer values of R1-R3 link were 30, 120, 120
The OSPF timer values of R2-R3 link were be 10,40,40

Looking at he result of show int s1/0 and s1/1. : these are my main points :

-Obviously the question is not the same as Digitaltut .

-I would run “show ip ospf neighbor on R3 or R1 ” showing neighbor A is not ture . not showing neighbor A might be the one.

-checking the status of both “R1-R3” – “R2-R3″…

The OSPF timer values of R2-R3 link were be 10,40,40 …this result exclude answer C.

The OSPF timer values of R1-R3 link were 30, 120, 120…this is result examines answer B .

B can’t be true unless R1-R3 link was point-to-point/Broadcast . IF R1-R3 was NBMA that will mean B is wrong.

Which will only leaves A.

one more thing is to notice the “S” at statements >>If R1-R3 was p2p/Broadcast that means we have two winners “A and B”.

I didn’t take the test yet . can’t tell if selecting more than one statement is an option .

@George and Ahmed

What is wrong with answer B?
When you do show ip ospf interfaces and check connections to R3 and see the below values that mean B is th correct answer.

Serial1/0 is up, line protocol is up
Internet Address 192.168.23.3/24, Area 0
Process ID 1, Router ID 3.3.3.3, Network Type NON_BROADCAST, Cost: 64
Transmit Delay is 1 sec, State WAITING, Priority 1
No designated router on this network
No backup designated router on this network
Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5

Also when a connection between 2 routers is a point to point and the OSPF defined as point to point, it has to be NON_BROADCAST. It cannot be broadcast. Your below comment is wrong :
“B can’t be true unless R1-R3 link was point-to-point/Broadcast “

@maybe Thanks for the clarification. that makes sense.
Also, you mentioned about a August pdf? did you mean July.

Can somebody please tell
Me if the July PDF is enough
I’m going out of my mind here

Thanks

@Nik
OSPF point to point links are of type “Point to Point” and not non-broadcast. On a point to point there is no DR/BDR elected because by definition there are only 2 end points and there is inherent connectivity. The Hellos are still sent and their is still an OSPF adjacency created and the state will be Full/ -. The multicast used between the 2 points is 224.0.0.5.

So point to Points are still broadcast.

Easiest answer to check is to build the lab and have a look with Wireshark.

Whoever did the 300-101 exam recently, please advise what are the LABs which they had on the exam. Please.

Hi,

Get Dumps? is that a spam?

Hi Guys,

Got my exam end of the month will July PDS be enough to pass? can somebody respond to my question please

@route-quest

Yes sorry i meant July for digitaltut. Time flies too fast.

@Dingo

can i have it

Maan(dot)khlil(at)(gmail)

please share

new dump

to mail below

maan(.)khlil(@)gmail

please share

new dump

to mail below

maan(.)khlil(@)gmail

@maybe Thanks
@Dingo – if I see anyone copying and pasting the same topics saying they have passed the exam with the link at the bottom. My eyes automatically filters them out. ;) We are on the same boat expecting to take the exam end of this month. Good luck mate.

@Route-quest

Ok thanks ill filter that. You 2 mate good luck have you been through the july PDF and Labs?

Thanks
Charlie

yep going through the labs now.hopefully CBT Nuggets videos to get an understanding and July pdf should do the job.🤞

@Route-quest

Brilliant I recommend the INE stuff as CBT Nuggets does not go in to real depths of a lot of topics. What day are you going for the exam? Have you got it booked

Thanks mate

that’s right mate.I only use the official route book and INE if I need to deeply understand any topics.:) My exam is next week.when is yours?

No mate just need to set the virtual-link commands between the ABRs

practice this is gns3

@Maybe,

Thanks for the clarification and updates.

Any more information on the new 10 questions mentioned earlier? Anyone sat the exam recently?

any one take the exam recently !!
plz advice me and share experience
i have exam tomorrow -_-
thanks in advance

@ahmedahmed,

I have exam the day after your. Please share your experience with me.

Thanks

@George and Ahmed

What is wrong with answer B?
When you do show ip ospf interfaces and check connections to R3 and see the below values that mean B is th correct answer.

Serial1/0 is up, line protocol is up
Internet Address 192.168.23.3/24, Area 0
Process ID 1, Router ID 3.3.3.3, Network Type NON_BROADCAST, Cost: 64
Transmit Delay is 1 sec, State WAITING, Priority 1
No designated router on this network
No backup designated router on this network
Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5

Also when a connection between 2 routers is a point to point and the OSPF defined as point to point, it has to be NON_BROADCAST. It cannot be broadcast. Your below comment is wrong :
“B can’t be true unless R1-R3 link was point-to-point/Broadcast “

@Nik

We are discussing Ahmed Exam version not Digital version:

on Ahmed Exam version : answer B is about R2-R3 not R1-R3.

When he ran show int >>> he found R2-R3 timers were 10 40 40 . which doesn’t meet option B .

########################################

Ahmed Exam Version

#############################################

Check the serial links connected to R3. Which statements are correct?
A. The neighbor command must be used on R1-R3 link to keep the adjacency up
B. The OSPF timer values of R2-R3 link are 30, 120, 120
C. The OSPF timer values of R1-R3 link should be 10,40,40
D. R3 must flood LSUs to all the routers on the network.
we
when I check show int s1/0 and s1/1 i got the following:

The OSPF timer values of R1-R3 link were 30, 120, 120
The OSPF timer values of R2-R3 link were be 10,40,40

########################################################

Please be careful , there is 3 versions of this question at Cisco pool to my knowledge.

Digitaltut only has one case . which is the one you were referring to .

I hope this was informative and helpful.

Good Luck .

If anybody does the exam can they share there experience

Thanks
Charlie

@ George
Could you please tell me what are the three versions of that questions.
I’m retaking this weekend.
if the same question came back again what I need to do ?
Also can any one tell me is July PDF is enough to pass. as I got many new questions which were NOT on this website….. mostly for AAA and IP SLA

anyone from preemium member,
is it interesting to get on premium !? MCQ & Labs are updated !!?
Thanks

Has anyone gone for the exam today?