Share your ROUTE v2.0 Experience

If the interfaces from R1-R3 or R2-R3 have been mixed, would that be just question 2 who is affected?

Question 2
Check the serial links connected to R3. Which statements are correct?
A. The neighbor command must be used on R1-R3 link to keep the adjacency up
B. The OSPF timer valueqes of R2-R3 link are 30, 120, 120
C. The OSPF timer values of R1-R3 link should be 10,40,40
D. R3 must flood LSUs to all the routers on the network.

Anyone please provide the link to MPQ, NUQ5, NUQ6 dumps ..

Need help on the below ques …

QUESTION 14
In which scenario can asymmetric routing occur?
A. active/active firewall setup
B. single path in and out of the network.
C. active/standby firewall setup
D. redundant routers running VRRP

Ans: A or D ??

——————————————————-
QUESTION 1
Which statement about stateless and stateful IPv6 autoconfiguration are true?
A. Both stateless and stateful autoconfiguration require additional setup
B. Stateless autoconfiguration requires no additional setup, whereas stateful autoconfiguration requires additional setup
C. Stateless autoconfiguration requires additional setup, whereas stateful autoconfiguration requires no additional setup
D. Both stateless and stateful autoconfiguration require no additional setup

Ans: A or B ??

————————————————————–
QUESTION 46
Engineer has to enable RIP on a link. Where he will issue the command?
A. Ipv6
B. Global
C. Router sub command
D. Interface subcommand

Ans: C or D ??

———————————————————————–
QUESTION 54
Other than a working EIGRP configuration, which option must be the same on all routers for EIGRP authentication key rolleover to work correctly?
A. SMTP
B. SNMP
C. Passwords
D. Time

Ans: C or D ??

————————————————————————-
QUESTION 73
Which type of address does OSPFv3 use to form neighbor adjacencies and to send LSAs?
A. unicast IPv6 addresses
B. link-local addresses
C. multicast address FF02::5
D. unicast IPv4 addresses

Ans: B or C ??

———————————————————————————-
QUESTION 89
Which BGP option is required when load sharing over multiple equal-bandwidth parallel links from a single CE
router to a single ISP router over eBGP? Select the best response.
A. eBGP Multipath
B. eBGP Multihop
C. BGP Synchronization
D. Public AS numbers

Ans: A or B ??

————————————————————————————–
QUESTION 11
When unicast reverse path forwarding is configured on an interface, which action does the interface take first
when it receives a packet?
A. it verifies that the source has a valid VEF adjacency.
B. It checks the egress access lists.
C. it verifies a reverse path via the FIB to the source.
D. It checks the ingress access lists.

Ans: C or D ??

———————————————————————————————–
QUESTION 1
Refer to Exhibit. Which two reasons for IP SLA tracking failure are likely true? (Choose Two)
A. The source-interface is configured incorrectly.
B. The destination must be 172.30.30.2 for icmp-echo.
C. A route back to the R1 LAN network is missing in R2.
D. The default route has wrong next hop IP address.
E. The threshold value is wrong.

Ans: AC or CE ??

—————————————————————————————————
QUESTION 8
Refer to the exhibit

configure terminal
ip flow-export destination 192.168.10.1 9991
ip flow-export version 9

How can you configure a second export destination for IP address 192.168.10.1?
A. Specify a different TCP port
B. Specify a different UDP port
C. Specify a VRF
D. Configure a version 5 flow-export to the same destination
E. Specify a different flow ID

Ans: B or C ??

————————————————————————————————————–
QUESTION 4
Which three NTP operating modes must the trusted-Key command be configured on for authentication to
operate properly? (Choose Three)
A. interface
B. client
C. peer
D. server
E. broadcast

Ans: BCE or BCE ??

———————————————————————————————————————

Just got out of the exam and passed it. All the questions I got are from NQ5 and 6. Drag nad drop are accurate as well. For labs I got PBR, Redistribution (with distance eigrp 90 105) and ospf eval.

For the OSPF Eval, since the ips have changed, need to be careful. All the related questions are the same but the answers will be different. Remember all the commands stated on the july dumps and practice it.

what are NQ5 & 6 question any one can mention link or past it here

Thank you

Anyone please provide the link to MPQ, NUQ5, NUQ6 dumps

Anybody to make me understand what is MPQ, NUQ5 and NUQ6 ? and where can I get those?

please anyone send me MPQ, NUQ5, NUQ6

noorkhanpk1978 at gmail.com

access-list 1 permit 1.0.0.0 0.255.255.255
router rip
default-metric 1
redistribute eigrp 20 distribute-list 1 out eigrp 20

Which routes will be injected into the routing protocol?

A. the EIGRP 20 routes into RIP that match access-list 1
B. any routing update with a metric of 1
C. all RIP routes into EIGRP 20
D. the RIP routes into EIGRP 20 that match access-list 1

Is the Answer A or C ? Am kinda confused, someone help please..

as per dumps

A. the EIGRP 20 routes into RIP that match access-list 1

please anyone send me MPQ, NUQ5, NUQ6

noorkhanpk1978 at gmail.com

@Sami, thanks, that answer is correct, I had to lab up the scenario to prove it.

Hi,

Does anyone have the new AAA drag and drop question?

Thanks

Taking my exam in 2 hrs.
Really nervous. Will update after the test what happens..

What is the command to enable IPv6 access list?

A. ipv6 traffic-filter access-list-name {in | out}
B. ipv6 access-list [access-list-name]
C. access-list ipv6 [access-list-name]
D. ipv6 access-group [access-list-name] {in | out}

Answer: A

Answer is A and B. A is used on a interface and B on a VTY line for instance.

Passed route test with 9xx/1000..

Which two configurations can a PPPoE client support? (Choose two)

A. Eight clients are configured on a single CPE
B. The client is connected to multiple hosts over DMVPN
C. The client is installed on the same network device as the server
D. The client is connecting over an ATM PVC
E. The client is installed on a native IPv6 network

Answer: A B

The reference in q&A is obsoleted and the new reference is https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/bbdsl/configuration/15-mt/bba-15-mt-book/bba-ppoe-client.html#GUID-8A60865D-0D92-4340-966A-3FB881416255 there is no presence of DMVPN in the new reference but half the document is for PPPoE client connecting over an ATM PVC so would appear that A and D are more suitable response.

@ Aatankari , Congratulations.
is the dump “ROUTE_July_2019” still valid?
what was the new questions??
your help is really appreciated

@Peyman , Thank You
July Dump is still valid but questions are abit tricky..If you know the concept then you are good to go..
I have not encountered any new questions..
Heading for Switch now..
Best of Luck

@ Aatankari

what about Labs

@Aatankari, do we have to study the whole July pdf ?

Which two commands configure on a DMVPN hub to enable phase 3? (Choose two)
A. ip nhrp interest
B. ip nhrp redirect
C. ip nhrp shortcut
D. ip network id
E. ip nhrp map
F. ip redirects

Dupms says Answer: B C

Need help here, isn’t “ip nhrp shortcut” a Spoke command ?

@ MPLS-label

can you please send me dumps @ {email not allowed}

@ MPLS-label

can you please send me dumps noorkhanpk at gmail.com

@ MPLS-label

can you please send me dumps noorkhanpk1978 at gmail.com

you guys need to read back instead of flooding stupid questions.

where can i get july dumps?
do you we need to study all?
what are the labs?
etc etc

the site is already a very good source to pass the exam. so to all stupid people who keep on spaming this page, f*ck off. supposing you pass your exam, the real world will not be the same for you idiots. anyways im out a here and going forward ccie.

Thanks a bunch to all those people who are legit in terms of helping.

well said. we should keep that post in rotation. :)

please help me:

I found these two similar questions but different answers with one another
Please help me which one is valid

Question 15

What are two differences between SNMP traps and SNMP informs? (Choose two)

A. Only informs provide a confirmation of receipt
B. Traps are more reliable than informs because they generate PDUs from the network manager
C. Only informs are discarded after delivery
D. Only traps are discarded after delivery
E. Informs are more reliable than traps because they require TCP three-way handshake.
Answer: A D

QUESTION 796
What are two differences between SNMP traps and SNMP informs? (Choose two)
A. Only informs provide a confirmation of receipt
B. Informs are more reliable than traps because they require a TCP three-way
handshake
C. Only traps are discarded after delivery
D. Traps are more reliable than informs because they generate PDUs from the network
manager
E. Only informs are discarded after delivery
Correct Answer: AE


Hello Everyone, Passes my Exam today with 948/100.

Labs: OSPF Eval, PBR and EIGRP-OSPF Redistribution

DnD: Frame Relay, AAA, NAT64, GRE

There were a few questions I have study from that dumps So make sure you study the MPQ, NUQ5, NUQ6 and that you understand the concepts,

Without 2 star**
http:/*/alt*url.com/tjwjz

What are two differences between SNMP traps and SNMP informs? (Choose two)

A. Only informs provide a confirmation of receipt
B. Traps are modre reliable than informs because they generate PDUs from the network manager
C. Only informs are discarded after delivery
D. Only traps are discarded after delivery
E. Informs are more reliable than traps because they require TCP three-way handshake.
Answer: A D

@ Toyang August 5th, 2019

dont b over confident after passing exam, sure some one or 9tut help you to pass

you seems aggressive and hampering person
to have good technical person in real world this approach will not help you, will F**k u in ur job

@Noor
Its all here

https://www.mediafire.com/file/4od833l6ow5604l/ROUTE_July_2019.pdf

Thanks a lot @Anonymous.

he wasnt being overconfident – i have been using this site for long time now and a lot of people always ask the same thing and NEVER look for it or ask for it to be emailed to them, like google and looking back on here is IMPOSSIBLE.

for everyone who hasnt taken the test, learn the concepts and then revise. simple.

the site here says where the july pdf is and other stuff is in the comments. just take time and look.

everyone, could you help me with this questions and provide link for your answer.

Question 10
With PCA and PCB and there are three routers between them and a different MTU value and they want a PCA to run an application with PCB and DF is set so we have to choose?
A. MSS
B. PMTU
C. GRE

this one has been seen i think from multiple test takers and their answers have been different

@acme

It’s PMTUD.

thanks anon.

anybody knows this one?
Which limitation is introduced when you deploy RIPv2 on a network that uses supernet advertisement?
A. RIPv2 supports only classful supernet networks
B. RIPv2 supports only supernet component networks that use VLSM C. Supernets are not supported in a RIPv2 environment
D. RIPv2 supports only classless supernet networks

@all who asked ..

labs :
PBR but IPs has been changed
ospf-eigrp redistribution with ethernet link
ospf evalution

D&D :
2xAAA
GRE
1 about unicast

Multiple Choice :
All from July Dump but words have been changed so just be a little careful.

Single Choice :
Everything from July Dump

Encountered only 1 question I have not seen in the dump about eigrp path selection. I dont remeber the question though.

Well now taking my 2nd test i.e switch within 1 month so see you everyone there.

Thanks to everyone who shared the expirence and a big thanks to digitaltut.

Hello All
Just wondering where to find July Dump,

Many Thanks in advance

@ AHM just mention ur email

@Noor
Thank u friend I found it in one of the previous pages.

Passed Exam today. Questions that NIBS posted on comments page 330 were on the exam. I’d say all but one or two. PBR, OSPF/EIGRP SIM, and only 1 drag and drop. I had about 5 questions that I didn’t recognize from the July dump. Good luck to those testing in the next few days.

Seems to be alot of D&D questions to remember :( Do I need to prepare for them all?

@123
what dumps you studied other than NIBS questions ??

Which two statements about AAA implementation in a Cisco router are true? (Choose two)
A. RADIUS is more flexible than TACACS+ in router management.
B. RADIUS and TACACS+ allow accounting of commands.
C. RADIUS and TACACS+ encrypt the entire body of the packet.
D. RADIUS and TACACS+ are client/server AAA protocols.
E. Neither RADIUS nor TACACS+ allow for accounting of commands.

Answer: B D

Cisco IOS implementation does not support command accounting for Radius. Exact quote from IOS https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_usr_aaa/configuration/15-mt/sec-usr-aaa-15-mt-book/configuring_accounting.html is:

“The Cisco implementation of RADIUS does not support command accounting.”

The same is repeated in the IOS XE document https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_usr_aaa/configuration/xe-3s/sec-usr-aaa-xe-3s-book/sec-cfg-accountg.html.

Seems like B is incorrect and so are the remainder.

@Noor
http://www.digitaltut.com/route-questions-and-answers
I studied the July dumps from this link on this site. I’d make sure you know the exact answers b/c they will switch the order of answers around.

@redwhiteblue
I put 25 drag & drops to memory and only had one on the test.

@maybe

I Think D and E are the right answers, look at thins link:

https://www.cisco.com/c/en/us/support/docs/security-vpn/remote-authentication-dial-user-service-radius/13838-10.html

@ Route Master. August 7th, 2019 he is posting whatapp group and trying to sell outdated dumps

FAKE FAKE FAKE FAKE
every time posting with different name take care

Route Master. August 7th, 2019 is FAKE FAKE FAKE FAKE FAKE FAKE

Related to the exam any news guys?

anyone have a vce file for july 2019 dumps ?