Share your ROUTE v2.0 Experience

haris_sikander @ hotmail . com

Passed the exam last week.

About 70 – 75% questions were from MPQ / NUQ 5 / NUQ6.

Rest from the old question pile and one or two new questions, which you should be able to answer.

Good luck everyone!

@lion… congrats buddy, kindly send me the dumps you used on haris_sikander @ hotmail . com
… or you can share the link from where i can download

@harry – I would recommend using the Premium account in Digitaltut. That’s the only resource I used for reviewing the questions apart from going through the official cert guide and CBT nuggets.

@lion.. thanks for your message…. i too have gone through cbtnuggets, but just to make sure let me ask, as far as route dumps are concerned, if i go with digitaltut premium account, will this be sufficient to pass the exam?

hello everyone.

which lab and dnd is coming in exam? do i prepare all lab given the pdf? simlets also coming?

Thanks

@PLASEANSWER “C” is correct

Please can anyone help by sharing the curent dumps here.
Thank you for doing so to enable me pass my exam.

Hi all,
Can somebody post the link for July dump please?

dang on the july pdf shared by digitaltut, there are lots of new questions compared to June pdf. It seems that these new questions are actually from past question dumps.

A new question from me.

Which configuration can you apply to a device so that it always blocks the outbound web traffic on Saturdays and Sunday between the hours of 1:00 AM and 11:59 PM?

A.
time-range SATSUN periodic Saturday Sunday 1:00 to 23:59
access-list 102 permit udp any any eq 80 time-range SATSUN X

Where can I find the july dump??
plz give me a hand…

no there isnt a lot of new questions, i had the july version and everything was the same bar 5 questions. please dont spread lies like that.

tommrow is my exam anyone recently attempt 300-101 exam, what labs were.

me also going for exam day after tomorrow anyone please share experience who gave exam recently

khan and anonymous .. best of luck for your exam .. hope you guys will clear this .. i have my exam next week .. please share what question you get in the exam ..

QUESTION 796
What are two differences between SNMP traps and SNMP informs? (Choose two)
A. Only informs provide a confirmation of receipt
B. Informs are more reliable than traps because they require a TCP three-way
handshake
C. Only traps are discarded after delivery
D. Traps are more reliable than informs because they generate PDUs from the network
manager
E. Only informs are discarded after delivery
Correct Answer: AE or AC? please help…….

I had premium membership previously and had copied and pasted all contents on a word file so I dont have to renew if i lost my membership. Downloading the July pdf and comparing it have new questions.

also comparing it to chinese file June 18 version, there are lots of wrong answers there. the VCE files are useful though

fair enough – my apologies.

if the answers are wrong on that one, then i will stick with the june pdf version as i am using that one and dexter.

do you have the vce files at all?

it is C – that is the only way. Loose does not exist as an option.

please share with us the valid dump 300-101 pdf format . i have the test next week

everithing is from digitaltut. i passed today exam 8xx score. premium member is enough same labs same sims same questions. labs redistribution and pbr.

congraats to everyone who recenlty wrote and pass the exam.

can someone please share the july pdf format. i have an exam this friday

I passed my exam today. Thanks a lot to digitaltut and every person who share their experience here. I used to studied cbt nuggets, ine, route cert guide.

Thanks all people from this community. Passed two days ago.
all questions from July Dump.

I had no new questions just some questions with simillar answers from july dump

Lab: PBR, Redistribute, OSPF Eval.

~2 D&D:
Frame Relay
NAT64

studied just from july file

https://www.digitaltut.com/route-questions-and-answers

good luck to everyone.bye

congrats @zenoss may i know if you have encountered any excess questions coming from July pdf? Or are your questions just came from MCQ NUQ5 and 6?

Hi,

Could someone send me the dumps to hansenbiler88 @ gmail . com

Thank you very much!

Amanda, you can find the July dump at https://www.digitaltut.com/route-questions-and-answers.

Good luck!

Passed today 300-101

congrats :) how did you find it?

Hi just failed today i prepared some short dumps which i got only 3 of them in the exam and the lab was PBR, redistribution eigrp and ospf, simulation questions same ospf.
D&D was ACL & GRE
2 days back one student also reported they changing D&D frequently which ignored so please prepare all.
i have prepared a file from digitaltut dumps and i find out of 55 question 44 including lab from it in my exam.
it takes me 3 hours to find these question so sharing you all in a post so prepare it before you go
all the best and please help others cheers

Dumps file:
Question 1
Where can NetFlow export data for long term storage and analysis?
A. syslog
B. collector
C. another network device
D. flat file

Answer: B
Question 2
In which two ways can NetFlow data be viewed? (Choose two)
A. CLI
B. NetFlow collector
C. built-in GUI
D. syslog server interface E. web interface

Answer: A B
Question 3
Refer to the exhibit.
Routing Protocol is “ospf 1”
Outgoing update filter list for all interfaces is not set
Incoming update filter list for all interfaces is not set
Router ID 10.1.1.1
It is an area border and autonomous system boundary router
Redistributing External Routes from,
bgp 800, includes subnets in redistribution
Number of areas in this router is 1. 1 normal 0 stub 0 nssa
Maximum path: 4
Routing for Networks:
10.1.1.0 0.0.0.255 area 0
Reference bandwidth unit is 100 mbps
Routing Information Sources:
Gateway Distance Last Update
Distance: (default is 110)
Based on the output from the show ip protocols vrf RED command, what is happening with the routing processes?
A. OSPF 1 is redistributing into BGP 800
B. Static routes are redistributed into OSPF 1
C. BGP 800 is redistributing into OSPF 1
D. Static routes are redistributed into BGP 800

Answer: C

Question 4
Which type of Cisco Express Forwarding adjacency is created when the next hop is directly connected, but its MAC header rewrite information is missing?

A. punt
B. discard
C. null
D. glean

Answer: D

Question 5

Refer to the exhibit. access-list 1 permit 1.0.0.0 0.255.255.255 router rip default-metric 1 redistribute eigrp 20 distribute-list 1 out eigrp 20

Which routes will be injected into the routing protocol?
A. the EIGRP 20 routes into RIP that match access-list 1
B. any routing update with a metric of 1
C. all RIP routes into EIGRP 20
D. the RIP routes into EIGRP 20 that match access-list 1

Answer: A

Question 6
What command can you enter to configure an enable password that uses an encrypted password from another configuration?
A. enable secret $abc%!e.Cd34$!ao0
B. enable secret 7 Sabc%!e.Cd34$!ao0
C. enable secret 0 Sabc%U*.Cd34$!ao0
D. enable secret 5 $abc%!e.Cd34$!ao0
E. enable secret 15 $abc%ie.Cd34$!ao0
F. enable secret 6 $abc%!e.Cd34$!ao0

Answer: D
Question 7
Which condition must be met before you can configure SSH on a device running Cisco IOS?
A. The device must have an auxilary port
B. The device must have a modem connection
C. The IOS must be a crypto in
D. Telnet must be disabled on the device

Answer: C

Question 8
Which command instruct a PPPoE client to obtain its IP address from the PPPoE server? (OR What command is needed to get the ip address assigned from the PPPOE server?)
A. interface dialer
B. ip address negotiated
C. pppoe enable
D. ip address dhcp
E. ip address dynamic

Answer: B

Question 9
Which Cisco Express Forwarding component maintains Layer 2 next-hop addresses that are used for hardware switching?
A. adjacency table
B. RIB
C. ARP table
D. FIB

Answer: A

Question 10
Which two statements about Frame Relay LMI autosense are true on a router? (Choose two)
A. It requires the LMI type to be explicitly configured
B. It operates on Frame Relay DTE interfaces
C. It operates on Frame Relay DCE interfaces
D. It operates when the line is up but the line protocol is down
E. It requires the line protocol to be up

Answer: B D

Question 11 (posted at Q.1 of http://www.digitaltut.com/gre-tunnel)
Refer to the exhibit. After configuring GRE between two routers running OSPF that are connected to each other via a WAN link, a network engineer notices that the two routers cannot establish the GRE tunnel to begin the exchange of routing updates. What is the reason for this?

A. Either a firewall between the two routers or an ACL on the router is blocking IP protocol number 47.
B. Either a firewall between the two routers or an ACL on the router is blocking UDP 57.
C. Either a firewall between the two routers or an ACL on the router is blocking TCP 47.
D. Either a firewall between the two routers or an ACL on the router is blocking IP protocol number 57.

Answer: A

Question 12
Which Cisco VPN technology can use multipoint tunnel, resulting in a single GRE tunnel interface on the hub, to support multiple connections from multiple spoke devices?
A. DMVPN
B. GETVPN
C. Cisco Easy VPN
D. FlexVPN

Answer: A

Question 13

Which three problems result from application mixing of UDP and TCP streams within a network with no QoS? (Choose three)
A. starvation
B. jitter
C. latency
D. windowing
E. lower throughput

Answer: A C E

Question 14
You want to configure a device to select an OSPF-learned route as the preferred path over an EBGP-learned route. Which action must you take?
A. Increase the OSPF cost
B. Decrease the OSPF cost
C. Increase the OSPF administrative distance
D. Decrease the OSPF administrative distance

Answer: D
Question 15
Afer configuring RIPng on two routers that are connected via a WAN link, a network engineer notices that the two routers cannot exchange routing updates. What is the reason for this?

A. Either a firewall between the two routers or an ACL on the router is blocking UDP 521
B. Either a firewall between the two routers or an ACL on the router is blocking TCP 520
C. Either a firewall between the two routers or an ACL on the router is blocking TCP 521
D. Either a firewall between the two routers or an ACL on the router is blocking UDP 520

Answer: A

Question:16

A network engineer is troubleshooting connectivity issues with a directly connected RIPng neighbor. Which command should show directly connected RIPng neighbor adjacencies only?

A. router#show ipv6 rip next-hops
B. router#show ip rip neighbors
C. router#show ipv6 routers
D. router#show ipv6 rip database

Answer: A

Question 17 (posted at Q.7 of http://www.digitaltut.com/ospf-questions)
A network engineer enables OSPF on a Frame Relay WAN connection to various remote sites, but no OSPF adjacencies come up Which two actions are possible solutions for this issue? (Choose Two)

A. Change the network type to point-to-multipoint under WAN interface
B. Enable virtual links
C. Change the network type to nonbroadcast multipoint access
D. Configure the neighbor command under OSPF process for each remote site
E. Ensure that the OSPF process number matches among all remote sites

Answer: A D

Question 18

A router was configured with the ―eigrp stub‖ command. The router advertises which types of routes?
A. connected, static, and summary
B. static and summary
C. connected and static
D. connected and summary

Answer: D

Question

Refer to the exhibit. The network setup is running the RIP routing protocol. Which two events will occur following link failure between R2 and R3?

RIPv2 Question. Cannot receive RIP updates. Why?

A. Firewall Port block UDP 520
B. Firewall Port block TCP 520
C. Firewall Port block UDP 502
D. Firewall Port block TCP 502

Answer: A

Question 34

The OSPF database of a router shows LSA types 1, 2, 3, and 7 only. Which type of area is this router connected to?
A. stub area
B. totally stubby area
C. backbone area
D. not-so-stubby area

Answer: D

Question 35

Which type of BGP AS number is 64591?

A. a private AS number
B. a public AS number
C. a private 4-byte AS number
D. a public 4-byte AS number

Answer: A

Question 36
Refer to the exhibit. Router DHCP is configured to lease IPv4 and IPv6 addresses to clients on ALS1 and ALS2. Clients on ALS2 receive IPv4 and IPv6 addresses. Clients on ALS1 receive IPv4 addresses. Which configuration on DSW1 allows clients on ALS1 to receive IPv6 addresses?

DSW1#sh run int f0/0
Building configuration…
!
interface FastEhternet0/0
ip address 10.4.10.1 255.255.255.0
ip helper-address 4.4.4.4
duplex auto
speed auto
ipv6 address 2002:A04:A01:A04:A01/120
ipv6 enable
end
A. DSW1(config-if)#ipv6 helper address 2002:404:404::404:404
B. DSW1(config)#ipv6 route 2002:404:404::404:404/128 FastEthernet1/0
C. DSW1(dhcp-config)#default-router 2002:A04:A01::A04:A01
D. DSW1(config-if)#ipv6 dhcp relay destination 2002:404:404::404:404 GigabitEthernet1/2

Answer: D
Question 37

Which Cisco VPN technology uses AAA to implement group policies and authorization and is also used for the XAUTH authentication method?

A. DMVPN
B. Cisco Easy VPN
C. GETVPN
D. GREVPN

Answer: B

Question 38

Which three benefits does the Cisco Easy Virtual Network provide to an enterprise network? (Choose three)

A. simplified Layer 3 network virtualization
B. improved shared services support
C. enhanced management, troubleshooting, and usability
D. reduced configuration and deployment time for dot1q trunking
E. increased network performance and throughput
F. decreased BGP neighbor configurations

Answer: A B C

Question 32

Which configuration can you apply to a device so that it always blocks the outbound web traffic on Saturdays and Sunday between the hours of 1:00 AM and 11:59 PM?

A. time-range SATSUN absolute Saturday Sunday 1:00 to 23:59 access-list 102 permit tcp any any eq 80 time-range SATSUN access-list 102 permit tcp any any eq 443 time-range SATSUN interface Vlan 303 ip address 10.9.5.3 255.255.255.0 ip access-group 102 in

B. time-range SATSUN periodic Saturday Sunday 1:00 to 23:59 access-list 102 permit tcp any any eq 80 time-range SATSUN access-list 102 permit tcp any any eq 443 time-range SATSUN interface Vlan 303 ip address 10.9.5.3 255.255.255.0 ip access-group 102 in

C. time-range SATSUN periodic Saturday Sunday 1:00 to 11:59 access-list 102 permit tcp any any eq 80 time-range SATSUN access-list 102 permit tcp any any eq 443 time-range SATSUN interface Vlan 303 ip address 10.9.5.3 255.255.255.0 ip access-group 102 in

D. time-range SATSUN absolute Saturday Sunday 1:00 to 11:59 access-list 102 permit tcp any any eq 80 time-range SATSUN access-list 102 permit tcp any any eq 443 time-range SATSUN interface Vlan 303 ip address 10.9.5.3 255.255.255.0 ip access-group 102 in

Answer: B

Question 33

A corporate policy requires PPPoE to be enabled and to maintain a connection with the ISP, even if no interesting traffic exists. Which feature can be used to accomplish this task?

A. TCP Adjust
B. Dialer Persistent
C. PPPoE Groups
D. half-bridging E. Peer Neighbor Route

Answer: B

Question

Which protocols support DMVPN?

A. EIGRP
B. RIPv2
C. OSPF
D. BGP
E. ISIS
Answer: A C D
Question

Which two protocols are required for DMVPN? (Choose two)

A. IPSec
B. PPTP
C. mGRE
D. NHRP
E. Open VPN

Answer: C D

Question

Which three problems result from application mixing of UDP and TCP streams within a network with no QoS? (Choose three)

A. starvation
B. jitter
C. latency
D. windowing
E. lower throughput

Answer: A C E

Question 25
Refer to the exhibit. Router DHCP is configured to lease IPv4 and IPv6 addresses to clients on ALS1 and ALS2. Clients on ALS2 receive IPv4 and IPv6 addresses. Clients on ALS1 receive IPv4 addresses. Which configuration on DSW1 allows clients on ALS1 to receive IPv6 addresses?

DSW1#sh run int f0/0
Building configuration… !
interface FastEhternet0/0
ip address 10.4.10.1 255.255.255.0
ip helper-address 4.4.4.4
duplex auto speed
auto ipv6 address 2002:A04:A01:A04:A01/120
ipv6 enable
end

A. DSW1(config-if)#ipv6 helper address 2002:404:404::404:404
B. DSW1(config)#ipv6 route 2002:404:404::404:404/128 FastEthernet1/0
C. DSW1(dhcp-config)#default-router 2002:A04:A01::A04:A01
D. DSW1(config-if)#ipv6 dhcp relay destination 2002:404:404::404:404 GigabitEthernet1/2

Answer: D

Question: 26
A network engineer executes the command ―show ip eigrp vrf purple topology‖. Which type of information is displayed as a result?

A. routes for a global routing table
B. updates that were sent for a specific routing table
C. active neighbors for a global routing table
D. route successors for a specific routing table

Answer: D

Question 27

Which two statements about DMVPN are true? (Choose two)

A. IPsec encryption not supported with statically addressed spokes
B. It requires full-mesh connectivity on the network
C. It uses NHRP to create a mapping database of spoke addresses
D. Multicast traffic is not supported
E. It supports dynamic addresses for spokes in a hub-and-spoke VPN topology

Answer: C E

Question 28 (not sure was it? I have doubt)

A network engineer executes the show ip flow interface command. Which type of information is displayed on the interface?

A. route cache information
B. IP Cisco Express Forwarding statistics
C. error statistics
D. NetFlow configuration

Answer: D

Question 29

Which two statements about VRF-Lite configurations are true? (Choose two)

A. They support the exchange of MPLS labels
B. Different customers can have overlapping IP addresses on different VPNs
C. They support a maximum of 512,000 routes
D. Each customer has its own dedicated TCAM resources
E. Each customer has its own private routing table.
F. They support IS-IS

Answer: B E

Question 30

Which two statements about PPPoE packet types are true? (Choose two)

A. PADR is a broadcast packet sent from the client to request a new server
B. PADI is an initialization packet sent as a broadcast message
C. PADO is a unicast reply packet sent to the client
D. PADO is a broadcast reply packet sent to the client
E. PADR is a unicast confirmation packet sent to the client

Answer: B C

Question 31

What is the optimal location from which to execute a debug command that produces an excessive amount of information?
A. Vty lines
B. SNMP commands
C. A console port
D. An AUX port

Answer: A

prepare from below link.

https://www.digitaltut.com/route-questions-and-answers

In the exam, there is a question asking for OSPF router ID,
given that there are 2 loopback interfaces, 2 physical ip addresses.

Only the Higher loopback interface and 2 physical ip addresses are being advertised by network command in OSPF.

What would be the correct router ID?

July 30, 2019 Read Route_July_2019.pdf (almost all are there, 2 new questions which can be answered) Passed the exam 88*/1000

PBR
OSPF/EIGRP Redistribution
OSPF Evaluation Sim

Drag&Drop
1.
IPv6 NAT characteristic

NAT64:
+ Use Network-specific prefix
+ Modify session during translation
NPTv6:
+ Modify IP header in transit
+ Map one IPv6 address prefix to another IPv6 prefix

2.
+ network-specific stateful NAT64 prefix: IPv6 prefix assigned by an organization + NAT64 : supports application layer gateway
+ NPTv6 : translates 2001:1::/64 to 2001:2::/64
+ well-known stateful NAT64 prefix: supports IPv6 prefix 64:FF9B::/96

3. frame-relay component

+ SVC: A circuit that provides temporary on-demand connections between DTEs + LMI: A signaling mechanism for Frame Relay devices
+ DLCI: A locally significant ID
+ FECN: An indicator of congestion on the network
+ PVC: A logical connection comprising two endpoints and a CIR

4. uRPF

Loose Modes:
+ It supports using the default route as a route reference + It requires the source address to be routable
Strict Modes:
+ It can drop legitimate traffic
+ It permits only packets that are received on the same interface as the exit interface for the destination address

5. frame-relay

interface Ethernet0
ip address 10.1.1.2 255.255.255.0
interface Serial0
! Serial interface config
no ip address encapsulation frame-relay frame-relay lmi-type ansi
! subinterface config
interface Serial0.1 multipoint
ip address 192.168.1.5 255.255.255.240
frame-relay map ip 192.168.1.1 100 broadcast

6. AAA features
+ Authentication: challenge and response operation
+ Accounting: feature that logs network usage
+ TACACS+: authentication method that uses TCP
+ RADIUS: authentication method that uses UDP
+ Authorization: controls specific access privileges of a user

Thanks NIBS and congrats,

Don’t you remember any IPV^ questions if you had?

Thanks NIBS and congrats,

Don’t you remember any IPV6 questions if you had?

NIBS or anyone who has full access to digitaltut, if the july questions can be found here
https://www.digitaltut.com/route-questions-and-answers

then what’s the benefit of paying monthly fee to access digitaltut? thanks

Hi ,

I passed with 938/1000 , 29/7
Lab: PBR, redistribute case 2, ospf eval
D&D same
almost of on july digitut. Tks digitut

Writing in a few hours. Will let you know how it went :-)

Best of luck ManicSheep .. i am taking my exam comming sunday .. do let us know about your test ..

acme IS FAKE FAKE FAKE FAKE……..

acme IS FAKE FAKE FAKE FAKE…………

acme IS FAKE FAKE FAKE FAKE……..

Does anyone have CBT Nugget Cisco CCNP Route 300-101 Hands-On Labs documents? if you have please share. Thank you in advance.

pls anyone have a link for july dump on vce format?

Hello Everyone, Passes my Exam today morning ALHMDOLLEAH with 901*/100.

3 Labs:
– EIGRP /OSPF Redistribution/
– Policy Based Routing Sim Pbr
– OSPF Stub

4 Drag and Drop: Framrelay LMI / Loose/Strick Mode/ACL/GRE

any one want the dumps send your email .