Share your ROUTE v2.0 Experience

Q1. Which two actions correctly configure PPPoE on a client ?
a.Define a dialer interface
b.Create a dialer pool and bind it to the physical interface
c.Create a dialer pool and bind it to the virtual template
d.Define a virtual template interface

A and C

router eigrp 1
redistribute ospf 1 match external

A,E2 routes
B,E1+E2 routes

A or B?

@abdullah March 2nd, 2019
yes all DnD same everything from here.
NAT64 and missing frame relay configuration etc

Failed 300-101. Saw around 60% new questions. DnD and sims were different.

Failed today. Almst half of the qns were new. Anyone else faced this too?

I found this link on page 292;
https://ww w. mediafire.com/fil e/m iv0r7ras8p5u3d/ROUTE_Jan_2019.pdf

is that still a good link? is there a link for MPQ and NUQ that is more updated?

Daddu and Vasanth1991 what dumps did you use as a reviewer?

passed today, lots of different questions (maybe 10 to 15).

also study composite quizzes, a few questions from there.

if you can master the composite quizzes, MPQ and new questions, you should be fine.

new SIM question used redistribution, similar to the other redistribution question.

other SIM was route map.

D&Ds were the same (NAT process, frame relay)

Which two statements about NetFlow version 9 are true? (Choose two.)

A. It is IEEE standards based.
B. It is a Cisco proprietary technology.
C. It is IETF standards based.
D. It supports egress flows only.
E. It supports ingress flows only.
F. It supports ingress and egress flows.

From my opinion B and F. What do you think ? In the answers i can see C and F

@speed
Netflow version 9 is IETF standard based. So anwer is C & F.

@digitaltut please update premium section!!!!!!!!!!!!!!!!!!!!!

Hi Leerz,

Thanks for providing the link and it seems that new questions are added.

I barely passed the exam, if u want to pass, wait for a month for them to update

please can anyone help me with the link to download the training videos for route. switch and tshoot.

thanks

All the people saying the exam has totally changed, can you post some examples of the new questions?

@Mark it is already in the comments above.

@Anonymous

Thanks. In that case I don’t think those are new questions, I think they’re recycled old questions. Those questions are in the old dumps.

Which two statements about DMVPN are true? (Choose two)
A. IPsec encryption not supported with statically addressed spokes
B. It requires full-mesh connectivity on the network
C. It uses NHRP to create a mapping database of spoke addresses
D. Multicast traffic is not supported
E. It supports dynamic addresses for spokes in a hub-and-spoke VPN topology

NOTE:- As to why A & C correct answer ? please confirm

Please send to me Dump

this my email
alisaadd1990@ gamil.com

Just remove the space

.,:(*َََ_*َََ):,.

Please

@speed,
C&F

Which two options are limitations of stateful NAT64? (Choose two)
A. It is unable to route VRF traffic.
B. IT is unable to route multicast traffic.
C. It supports FTP traffic only with an ALG.
D. It supports DNS64 only.
E. Layer 4 supports TCP only

Hi, Can someone email me current dump? my email is
data4u333 @ yahoo.com

Which two options are limitations of stateful NAT64? (Choose two)
A. It is unable to route VRF traffic.
B. IT is unable to route multicast traffic.
C. It supports FTP traffic only with an ALG.
D. It supports DNS64 only.
E. Layer 4 supports TCP only

Answers: A and B

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipaddr_nat/configuration/xe-3s/nat-xe-3s-book/iadnat-stateful-nat64.pdf (page 2)

Restrictions for Configuring Stateful Network Address Translation 64

• Applications without a corresponding application-level gateway (ALG) may not work properly with the Stateful NAT64 translator.

• IP Multicast is not supported. ** ANSWER B **

• The translation of IPv4 options, IPv6 routing headers, hop-by-hop extension headers, destination option headers, and source routing headers is not supported.

• Virtual routing and forwarding (VRF)-aware NAT64 is not supported. ** ANSWER A **

• When traffic flows from IPv6 to IPv4, the destination IP address that you have configured must match a stateful prefix to prevent hairpinning loops. However, the source IP address (source address of the IPv6 host) must not match the stateful prefix. If the source IP address matches the stateful prefix, packets are dropped. Hairpinning allows two endpoints inside Network Address Translation (NAT) to communicate with each other, even when the endpoints use only each other’s external IP addresses and ports for communication.

• Only TCP and UDP Layer 4 protocols are supported for header translation.

• Routemaps are not supported.

• Application-level gateways (ALGs) FTP and ICMP are not supported.

• In the absence of a pre-existing state in NAT 64,stateful translation only supportsIPv6-initiated sessions.

• If a static mapping host-binding entry exists for an IPv6 host, the IPv4 nodes can initiate communication.

In dynamic mapping, IPv4 nodes can initiate communication only if a host-binding entry is created for the IPv6 host through a previously established connection to the same or a different IPv4 host. Dynamic mapping rules that use Port-Address Translation (PAT), host-binding entries cannot be created because IPv4-initiated communication not possible through PAT.

• Both NAT44 (static, dynamic andPAT) configuration and stateful NAT64 configuration are notsupported on the same interface.

Which two statements about DMVPN are true? (Choose two)
A. IPsec encryption not supported with statically addressed spokes
B. It requires full-mesh connectivity on the network
C. It uses NHRP to create a mapping database of spoke addresses
D. Multicast traffic is not supported
E. It supports dynamic addresses for spokes in a hub-and-spoke VPN topology

I think answers are C and E.

Which two statements about NetFlow version 9 are true? (Choose two.)

A. It is IEEE standards based.
B. It is a Cisco proprietary technology.
C. It is IETF standards based.
D. It supports egress flows only.
E. It supports ingress flows only.
F. It supports ingress and egress flows.

Answers are C and F.

https://www.cisco.com/c/en/us/products/ios-nx-os-software/netflow-version-9/index.html

Which two actions correctly configure PPPoE on a client? (Choose two)

a) Define a dialer interface.
b) Create a dialer pool and bind it to the physical interface.
c) Create a dialer pool and bind it to the virtual template.
d) Define a virtual template interface.

I think answers are A and B.

You are implementing WAN access for an enterprise network while running applications that require a fully meshed network, which two design standards are appropriate for such an environment?

a) A centralized DMVPN solution, to simplify connectivity for the enterprise
b) A dedicated WAN distribution layer, to consolidate connectivity to remote sites.
c) A collapsed core and distribution layer, to minimize costs
d) Multiple MPLS VPN connections with static routing
e) Multiple MPLS VPN connections with dynamic routing

I think answers are A and B. What do you think?

Which two piece of information can you determine from the output of the show ntp status command ?

a) The NTP version number of the peer
b) The configured NTP servers
c) The IP address of the peer to which the clock is synchronized
d) Where the clock is synchronized

I think answers are C and D. What do you think?

Router#sh ntp status
Clock is synchronized, stratum 3, reference is 200.XXX.XXX.XXX
nominal freq is 250.0000 Hz, actual freq is 249.9937 Hz, precision is 2**22
ntp uptime is 654773800 (1/100 of seconds), resolution is 4016
reference time is E02A7E69.60FE06D3 (10:10:10.378 XXX Wed Mar 6 2019)
clock offset is 2.1798 msec, root delay is 3.92 msec
root dispersion is 77.29 msec, peer dispersion is 0.10 msec
loopfilter state is ‘CTRL’ (Normal Controlled Loop), drift is 0.000025158 s/s
system poll interval is 1024, last update was 381 sec ago.

@ARD are those new questions?

Which task do you need to perform first when you configure IP SLA to troubleshoot a network connectivity issue?

a) Specify the test frequency

b) Enable the ICMP echo operation

c) Schedule the ICMP echo operation

d) Verify the ICMP echo operation

I think the correct answer is B.

https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/12-2/44sg/configuration/guide/Wrapper-44SG/swipsla.html

Yes @Anonymous, these questions are new.

A network engineer configures two connected routers to run OSPF in Area 0; however, the routers fail to establish adjacency. Which option is one of the caused for this issue?

A. Area numbers match.

B. OSPF process numbers do not match on both neighbor routers.

C. The same MTU sizes are configured on both sides.

D. The same OSPF router IDs are configured on both routers.

The correct answer is D.

A network engineer trying to synchronize the time clock but the time is not working. What is likely the cause of this problem?

A. Either a firewall between the two routers or an ACL on the router is blocking IP protocol number 123.

B. Either a firewall between the two routers or an ACL on the router is blocking UDP 123.

C. Either a firewall between the two routers or an ACL on the router is blocking TCP 123.

D. Either a firewall between the two routers or an ACL on the router is blocking IP protocol number 123.

The correct answer is B.

Which two statements about configuring Frame Relay point-to-multipoint connections are true? (Choose two)

A. They ignore the broadcast keyword in the frame-relay DLCI mapping.

B. They require the same DLCI on each side of the link.

C. Changing a point-to-multipoint subinterface to a different type requires the interface to be deleted and recreated.

D. They require the frame-relay mapping command to be configured.

E. They require inverse ARP.

Answers are D and E.

Which interface type does a PPPoE client use to establish a session?

A. Physical.

B. loopback.

C. visual-template.

D. dialer.

Answer is D.

Which values identifies VPNs in an EVN environment?

A. DLCI.

B. route target.

C. virtual network tag.

D. VLAN ID

Answer is C.

Which two protocols are required for DMVPN? (Choose two)

A. IPSec

B. PPTP

C. mGRE

D. NHRP

E. Open VPN

Answers are C and D.

Which statement about spilt-horizon rule for distance vector routing protocols are true?

a. A router advertises a route to an unreachable network with an infinite metric.

b. A router does not advertise routes to any neighboring router.

c. A router advertises routes back out the interface on which it learned them with an infinite metric.

d. A router does not advertise routes back out the interface on which it learned the route.

Answer is D.

What is the DHCP option to download TFTP info Cisco phone?

a. option 57

b. option 82

c. option 66

d. option 68

Answer is C.

When people talk about SIMs and state an EVAL, what is an eval? Is that like the simlet?

EVAL are like SIMs, but you just enter show commands and answer 4 or 5 questions about the topology.

What is OSPF Redistribution 2nd Case? I am seeing that a lot in the last few days. Does anyone have a dump for that SIM?

Just finished exam yesterday. Barely passed with 82x score. They changed 40% of the exam question. Better postpone your exam and wait until they update the question. If not, you guys better master the subject so doesn’t matter which question they ask you can still answer. The SIM I got was EIGRP redistribution, OSPF Eval, and PBR

@ccmks may I ask did you focus on MPQ and NPQ? what reviewer did you use for the exam? Thanks!

@Zeb MPQ and NPQ is that a dump or what ?

@refa premium section

Passed with a score in the mid-900s. Dumps are definitely valid if you do the old dumps as well as the MCQ/NUQ/Sims/DND. 5-6 new questions that were not that difficult.

Here’s as accurate info as I can give you.

Background: CCNP for over 10 years, recertifying.

I bought the official study guide for this: total waste of time. It’s over 1000 pages & I read it cover to cover.

It would help you answer maybe 10% of the questions at best. You could literally have it in the exam with you & fail

miserably. I was reading the Kindle version & as I went through the test questions here I was looking up each question &

the vast majority are not remotely covered. It’s basically a light overview, even though it’s so long.

The stories that the exam has massively changed should be taken with a pinch of salt, that was NOT the case. However you

definitely need to read the old dumps not just the MCQ & the NUQ. I went through every question in the old dumps (i.e.

the Dexter pdf) and the MCQ & the NUQ, checked every answer to see if I agreed (I didn’t always & I’ve posted on here

those I think are wrong) and practised until I knew every question with no errors.

I did have 5-6 new questions however they were either obvious or they were easy to narrow down to 2 answers. Basically

nothing to worry about if you know all the content on this site.

IMO some or all of the people on here saying the exam has massively changed have possibly not studied the old dumps, or

they looked superficially then forgot lots of the questions, or they’re trolling the forum so they can repost under a

different name to try to sell dumps.

Sims & DnD exactly as on here.

As I say, learn the Sims, the DnD, the MCQ, the NUQ, and the old dumps, and IMO you’ll be fine. There’s no reason not to

learn the old dumps anyway as even if those questions don’t come up they’re directly relevant to the exam content & will

teach you the concepts more thoroughly.

This is an excellent site, the Premium Membership is cheap & worth it for the Sim practice. Thanks to the genuine &

helpful people on here such as Speed, Leerz, Ciscoman, Yohei, Saji.

Thanks and congrats @MarkHall.

@Mark Hall , @ Speed- I want to congratulate you guys for the sharing of info. I also agree with Mark Hall that some people on this forum want just 53 questions and they are done. If in the exam there are 53 questions from a different pool , they are quick to say the exam has changed. I went for the Cisco exam in November ,having studied all 749 questions + Labs and I came out smiling. All my questions were from same site like this one . Now I had about 5 new questions (remember Cisco says you must expect these questions (referred as Beta Questions))So the main points are :1) Read the whole OCG and use gns 3 for lab practice 2) Be a premium member here 3) Practice all the q+ans 4) Check the forum here for some questions if you have doubts 5) Take your time -do not rush to write . After the whole experience – u will come out smiling. For some of us who will be going for the CCIE lab , there is simply no choice ,everything must be thoroughly done …..thats my 2 rupees or cents of advice here.

we do not want beggars the money here, please pay11$ and get Dumbs and ETC…
help Free or stay silent