Share your ROUTE v2.0 Experience

@LR

Search this forum and you will find the dump I think its on page 88 or 98 can’t remember.

@Mac I have found the “””300-101-ROUTEv1.5 (updated by procyber 01.11.2017)””” dump. Was there any update on it since then? I heard someone say “It’s me procyber” update is out there, I was hoping to get that. It might have some corrections to wrong answers plus new questions.

Hi Guys,

Cleared Exam with 94x this morning. All Questions were from 9 tut hence managed to completed exam in 50 minutes. Didn’t use any other dumps. Only studied from 9 tut , ine videos and cisco certified kevin wallace book.

Tab and ? working on all labs except 1.

Copy running-config start-up config only worked on OSPF sim ( WR was not working , advanced commands were not allowed like show run | section eigrp or ospf )

Will provide more updates on labs in few hours.

Thanks to 9tut and all members here.

9 tut is enough to clear 300-101 exam. You won’t need any other dumps.

Cheers for now

Had Below Drag & Drop in Exam today :-

Q5 from drag and drop 1 ( Authentication , Authorization , Accounting )
Note :- on right first section was Authentication , Second section was Accounting and 3rd option was Authorization.

Q8 ( NAT64 , NPTv6 ) from Drag and Drop 1

Q10 ( Frame-relay component one , SVC LMI ) Drag and Drop 1 section

Q13 ( Loose Mode , Strict Mode ) from Drag and Drop 1

Q4 ( IPv6 Traffic Filter , IPv6 Access Filter ) from Drag and Drop Section 2

PBR SIM :-

Next Hop is was different than one in 9 tut lab. Scenario wordings on exam was little bit different. But solution was the same as 9 tut.

2 links one Frame-Relay another one E0MPLS.

You can generate traffic after applying router configuration. There was a tab on host called ” generate traffic ” . After clicking it generated 9 packets. So you can verify it by doing show route-map and check for traffic match count of 9. Also you can check show access-list as well. Didnt try show ip policy as it was not required.

Try using different access- list number and route-map name . Most of us going for exam after checking 9 tut might be using same access-list number ( 101 ) and route-map name ( pbr).

EIGRP Evaluation Sim :-

Same as what we got here on 9 tut. Same answers as well.

Show running configuration was working on this sim.

Show ip eigrp topology didn’t work but show ip eigrp 1 topology was working .

Answers 333056 , 20 , CISCO , Distribute-list using ACL , 19:80.

For 19:80 question :-

R01 was only showing one next hop for R6’s loopback address in R1’s routing table.

Show ip route only listed one next hope for R6’s loopback address.

But when you check show ip route x.x.x.x ( where x.x.x.x is R6’s loopback address ) it did show two next-hops with traffic share of 19:80. Kind of a bug may be on sim.

You can find out R6’s loop back address by checking show ip route and look for connected route entry for loopback 0 or 1 there. I think show ip interface brief was working as well on R6 to check its loop back address.

OSPF Evaluation Sim :-

Show running-config disabled for this sim.

This has an error on topology diagram.

R3’s interface connected to R1 was actually connected to R2 and R3’s interface per topology diagram connected to R2 was actually connected to R1.

on R1 and R2 router side , interfaces were actually correct on topolgy diagram.

Make sure you login to R3 and find out which interface is connected to R1 and which one is connected to R2. One way for checking this is matching ip address subnet mask on R3-R1 and on R3-R2.

Correct answer on sim was R1-R3 link needs neighbor command for adjancey to stay up.

Reason :-

R1-R3 link was NBMA network type. Because multicasts are not supported on NBMA networks it requires neighbors to be statically defined for adjancey to come up.

Upon checking on R1 , show ip ospf neighbor , R3 was listed as neighbor in FULL state.

Timers between R1-R3 were 30,120,120 .

Link between R2-R3 was already point-to-point with /24 mask. Timers were 10,40,40 . So one the of option was timers between R2-R3 should be 30,120,120 which was not the case. so that option was incorrect.

So correct option was R1-R3 link needs neighbor command for adjancey to stay up.

SPF algorithm count on R4 for area 1 correct answer 9 as per show ip ospf command for R1.

For R5 and R6 question,

correct answer was R5′ loopback and R6’s loopback are both present in routing table of R5.

On exam , R6 had 2 loopback addresses ( checked as show ip route , connected routes listed for R6 loopback 1 and loopback 0) . R6 was not learning any R5’s loopback addresses , instead it learnt 0.0.0.0/0 O IA route.

On other side R5 learnt R6 loopback addresses as show ip route command on R5.

How old was Type 4 LSA from R3 for Area 1 on Router 5 :-

Correct answer was 1858.

Show ip ospf database on R5 showed summary LSAs for area 2 .

There were no type 4 LSAs on R5’s OSPF database.

Type 3 LSA’s listed LSIDs of 3.3.3.3 , 4.4.4.4 and few others but LSAge time was 1858.

On R3 when you issue Show ip ospf command.You can see type 4 LSAs in R3’s database for area 1 just for verification .

Only check timers on R5 not on R3 though.

OSPF Sim :-

Few Notes :-

Sim accepted copy running-config startup-config command on all routers. So save configuration at end. after testing ping from seattle to atlanta loopback.

Router Names were Atlanta ( lynaic in 9tut lab ) , St Lucia ( Amani) , Seattle ( Portaland).

IP addresses were different.

No configuration required on Atlanta router . It has loopback address configured which needed to be ping from Seattle router’s serial interface.

Atlanta loopback address was in area 1.

Link between Atlanta and st Lucia was in area 0. It was configured on both routers.

Exam asked :-

all routers should have ospf process id of 9.

Asked to configure link between St Lucia and Seattle to be in area 42.

Asked to configure Seattle interface ( connected to St lucia ) to be in area 42

asked to configure St Lucia’s interface ( connected to Seattle ) to be in area 42.

Both needed to be configured in a way that specific mask is used ( wild card 0.0.0.3 coz of /30 subnet)

– Area 42 should not receive any external or inter-area routers ( Didn’t mention ” except default route)

Note :- on Seattle router no ospf configuration was there. So you have to create ospf process as well.

Solution was :-

on Seattle ( Top Left as you on screen ):-

configute terminal
router ospf 9
network x.x.x.x 0.0.0.3 area 42
area 42 stub
exit
copy runnning-config startup-config

on St Lucia ( Middle Router ) :-

router ospf 9
network x.x.x.x 0.0.0.3 area 42
area 42 stub no-summary
exit
copy running-config startup-config

On St Lucia Middle router router ospf 9 was already configured along with link to atlanta.

Test Methods :-

show ip ospf database to ensure it Seattle and St Lucia forms neighborship.

Ping Atlanta’s loopback interface ip address from Seattle router to ensure connectivity.

Check on seattle that it learns 0.0.0.0/0 route no other inter-area or external routes.

OSPF – EIGRP Redistribution Sim :-

I think IP addresses were slightly different. Solution was Same As 9 tut case 2.

OSPF process id was 1 and EIGRP AS was 100.

Link between R2-R3 was ethernet link instead of serial link . So distance eigrp 90 105 was required.

Ping and traceroute was working on R01 only.

Exam asked to test ping or check route entry from R01 for network in cloud ( 172.16.x.x/24 , network connected left side of R04 in topology , it was not R04’s loopback address. it was something like a company merger or something ).

Exam asked to ensure that traffic from R01 to remote network 172.16.x.x should use optimal path with highest bandwidth.

So basically after configuring R02 and R03 ( use distance eigrp 90 105 under router eigrp 100 on R02) issue a ping from R01 to remote network 172.16.x.x/24 connected to R04.

You can also verify it by using traceroute 172.16.x.x command from R01 and check the path to ensure it takes R1-R2-R3-R4 path as per path listed on traceroute command.

Good Luck Guys.

Sorry guys i meant digital tut instead of 9tut for 300-101 route exam in all my previous comments.

Hai can someone share the real dumps that you used for your test.I need them badly.Please, some one helps me out.PLS

Hi Andy,

Preparing for writing ccnp route exam. Please share the dump @ muthu 884 @ gmail. com

passed Route exam 9xx. Thanks DIGITALTUT and Procyber.

One new question came for me.
Q1). Radius combined which of the following?
1. Authentication
2. Authorization
3. Accounting
4. Can’t remember
5. can’t remember
Answer is “Authentication & Authorization”

Even-though there were many new questions which are not in the Procyber 1.5 and was in the Valid dump I purchased, those questions didn’t come for me. I don’t know whether those will come or not for you. But I can recommend Procyber enough for passing the exam.

For more information, you can contact me through my email – sarangiha AT gmail
Thanks and Cheers!
Tom.

Hi all,
Tomorrow is my route exam. I am practicing procyber(1/11) dumps on vce, but some confusing about drag & drop Q’s as the vce incorrect my answers if i answer not as sequence of vce like “ipv6 router security features” drag n drop; like I answer corretly option under ‘ipv6 traffic filtering’ and ‘ipv6 access classes’ but if I place “it filters traffic at the interface level” on second sequence as on first “it supports tagged acls” ; then dumps vce incorrect my answers, similarly on other drag n drop as well.
I place the answers under correct options but not as dumps vce sequence.
Any one please inform me urgently that I need to remember the dumps vce ans sequence or not for my real exam ??
Thanks in advance.

Hi, I am starting my CCNP studies. Can anyone give some recommendations on study material/dumps etc?

Thanks.

Lunchi

Can you please specify the difference in the exam than the PBR in 9tut? it will help a lot. what did you type ?

@Lunchi You’re the man, thanks! I was really hoping that someone would outline the real lab configs here. I will save all your findings to practice and be prepared.

Do you remember anything else, like new questions? Thanks, mate!

Yes. Lunchi thank a lot man.

Did the test have a lot of IPV6 questions?

@ lunchi thanks alot for sharing.

Lunchi, did you see a lot of IPV6?

lunchi the mvp :D

Hi all,
Tomorrow is my route exam. I am practicing procyber(1/11) dumps on vce, but some confusing about drag & drop Q’s as the vce incorrect my answers if i answer not as sequence of vce like “ipv6 router security features” drag n drop; like I answer corretly option under ‘ipv6 traffic filtering’ and ‘ipv6 access classes’ but if I place “it filters traffic at the interface level” on second sequence as on first “it supports tagged acls” ; then dumps vce incorrect my answers, similarly on other drag n drop as well.

I place the answers under correct options but not as dumps vce sequence, the dumps vce incorrect my ans..
Any one please inform me urgently that I need to remember the dumps vce ans sequence or not for my real exam ??

Thanks in advance.

Please share CCNP ROUTE SWITCH AND TSHOOT books

Hi Guys which one correct for Drag &Drop 9TUT or Procyber there lots of confusions how they ara write both of them.
Thanks

Please Need the Video from Pluralsight, Implementing OSPF for CCNP Routing and Switching 300-101 ROUTE, link to download here or to {email not allowed}

Please Need the Video from Pluralsight, Implementing OSPF for CCNP Routing and Switching 300-101 ROUTE, link to download here or to nasyto at yahoo .fr

@LR
Don’t worry too much about any updates, just study the materials covered in the Cisco manual then study the dump and you will do just fine. Like I said I did not see any new questions so you should be just fine with that.

@ anyone whos taken the test. Is there a lot of IPV6 questions?

does anyone know the below questions answer:

Which two commands must configure in the calling router to support the PPPoE client?

a. pppoe-client dial-pool-number
b. pppoe enable group
c. Mtu
d. Peer default ip address pool
e. bba-group pppoe

@zaman
today pass me !

a and c incorrect good luck

passed with 829

some new question like :

which two features does radius combine?

the answer is authentication and authorization

Ark, did you see much IPV6?

Hello All,,

I’ll start studying CCNP route .. any recommendations ? from where can I start ? .. do you have any written material that I can use to study ?

Thanks in advance

Regards,
Asmaa Ali

SNMP is important protocls and you ll see in CCNA exam…
https://ipcisco.com/snmp/
check also this, I came across

Hi;

I have not been able to find the pdf version of procyber 1.5 dump since page 200, so please help. Is Procyber 1.5 up to date?

Do I need your help to work? I have only one test, and I will be CCNP if I take it.
Thanks?

hello @Lunchi,@Tom,@joe
Could you please help share me the procyber v1.5 and another dump that you have to me ? kindly thank for your help . please here in this chat or send via email reyaexam @gmail dot com

@Lunchi

Can you tell if you had any questions from the composite quizzes on digitaltut?

Here you go guys, for free

buy me a beer if you pass :)

https://mega.nz/#!tFMTCQzJ!sEQpzx3xRnkplOh-nG8N-rckxZSIdEwj69ux0sJvo0w

Hi Dexter.

Thanks for sharing. did you use this to pass the exam?

Passed today 12/23
1/ Procyber is valid. All Qs from it.
2/ I believe some answers in dump are wrong but can’t figure out which ones. But vpn mostly I guess cause I got 67% in this section.
3/ My email is mahmouddiser on hotmyl, if u have any questions pls email me. I won’t reply those asking for dumps, it’s here some pages back. I won’t also reply those asking about which questions I had cause it’s useless to know since Cisco change and rotate from the questions pool.

Good luck guys

Hello
Please share CCNP Route Dump
Thank you :)

Passed 300-101 exam with 9xx.
Lab are same as digitaltut. Procyber 1.5 (updated 01.11.2017) is valid.

Lab/Sim:
– OSPF evaluation
– EIGRP evaluation
– Redistribution
– PBR
– OSPF sim

DnD:
– Frame-relay components (DLCI, FECN, PVC, etc.)
– IPv6 NAT-PT/NAT64/Network specific/Well-known
– Authentication/Authorization/Accounting
– IPv6 Traffic Filtering/Access Classes
– Loose/Strict uRPF

MCQ:
Some of the questions I remembered include
17 43 102 120 171 190 198 215 218 219 223 231 252 277 283 284 290
297 309 311 340 341 343 383 392 396 434 439 440 441 442 444 445 446

Got 67% for VPN section, so answer for 1 or 2 VPN questions are wrong.

All the best!!

Can someone please link the procyber dump. Thank you so much.

Please someone share the drums you used to passe the exam,Req you

@Dexter
Thank you Dexter Do you have a PDF file of the vce file you shared

@Chazz congrats could you please share the link to study i am just starting preparing for routing.

@Diser congrats could please share Procyber pdf and vce link ?
thanks

I used have prociber dump + rest of dumps

https://mega.nz/#!tFMTCQzJ!sEQpzx3xRnkplOh-nG8N-rckxZSIdEwj69ux0sJvo0w