Share your ROUTE v2.0 Experience
Note: The last day to take this ROUTE 300-101 exam is February 23, 2020. After this day you have to take new Enterprise exams to get new CCNP Enterprise certification. If you want to find out more about the new exams please visit here. |
The ROUTE 300-101 (ROUTE v2.0) exam has been used to replace the old ROUTE 642-902 exam so this article is devoted for candidates who took this exam sharing their experience.
Please tell with us what are your materials, the way you learned, your feeling and experience after taking the ROUTE v2.0 exam… But please DO NOT share any information about the detail of the exam or your personal information, your score, exam date and location, your email…
Note: Posting email is not allowed in the comment section.
Your posts are warmly welcome!
Which two causes of latency are true? (Choose two)
A. High bandwidth on a link
B. Split horizon
C. Propagation delay
D. Serialization delay
E. Under-utilization of a link
which correct ans ??
What happens when unicast flood protection is triggered on a VLAN?
A. The VLAN is shut down
B. Traffic on the VLAN is load-balanced across multiple links
C The VLAN is removed from the VLAN database
D. Traffic on the VLAN is passed to another VLAN with lower load
Which two causes of latency are true? (Choose two)
A. High bandwidth on a link
B. Split horizon
C. Propagation delay
D. Serialization delay
E. Under-utilization of a link
which correct ans ??
Dear All,
Can anyone share the latest dumps please who have passed recently?
p o j a c k t @ g m a i l . c o m
plzzz
What is the difference between digital-tut Route-December and most-popular question ?
I passed with 894 points yesterday.
All questions are in Digitaltut .
I recommend you to become a premium member.
Thank you digitaltut!
@strom your email is wrong
Hi @ kani
I am waiting for your email.
Please send dump on sajedk55 @ g mail dot com
@kani , im taking exam on saturday …please help me with the dumps.
please send it to mahijini1 @ gmail com
Hi Kani,
Here is my email address: {email not allowed}
Will be patient waiting for your mail , unless you can share yours will reply back to you.
Hi Kani,
Here is my email address: mike(dot)reemed@gmail(dot)com
Will be patient waiting for your mail , unless you can share yours will reply back to you.
@Strom,Anonymous,Sj I send you all
I hope good lucky every One i start Switch. exam is just simple if you study well and prepare Digital-tut resource I hope success all I will stop for checking this site Thanks for those sharing information and update’s all together we can change world.
Just passed my exam 8xx, all labs and question came from this site, premium is all you need. Labs were Eigrp stub, ospf area, and Eigrp evulation lab. On to tshoot good luck!!
Hi @Kani,
I have the exam in early February, can you send me the dumps you have? Thank you very much, this is my mail: djxoxe @ hotmail . com
Hi Kani and İsmail, firstly congrats of you. pls can you share dumps with me. i m very glad if u can. enestorun @ hotmail(dot)com
I passed recently, most of the questions were the common ones previously listed here. If you put in the study time to learn the concepts and use the practice questions here with the premium member you will be fine.
going to exam next week, i hope the questions will keep the same. I already subscribed to premium membership, now let’s rock and roll :)
CONGRATULATIONS!!!
Just passed the 300-101 exam today!
Scored 9xx/1000!!!
That updated Pass Leader 300-101 dumps with 773 Q&As are stable and valid for passing.
The 300-101 test is stable and no new questions!
All questions were from Pass Leader, valid enough for passing!
Trying Pass Leader 300-101 dumps ASAP, all guys!
Good luck!!!
MORE:
The new Pass Leader 300-115 dumps (Jan/2019 Updated~~~1042 Q&As) now are available, here are part of 300-115 exam questions (FYI):
NEW QUESTION 1000
Which two control protocols use the native VLAN 1 by default? (Choose two.)
A. CDP
B. VTP
C. NTP
D. LACP
E. STP
Answer: AB
NEW QUESTION 1001
Which technology provides a multichassis IP connection between VSS-enabled switches and downstream devices?
A. LAG
B. PAgP
C. MEC
D. ICCP
E. LACP
F. BFD
Answer: C
NEW QUESTION 1002
If a switch that is configured globally with DHCP snooping receives a packet that has DHCP Option-82 set to 192.168.1.254, how does the switch handle the packet?
A. It forwards the packet normally.
B. It removes the Option-82 information from the packet and forwards the packet.
C. It drops the packet.
D. It replaces the source MAC address of the packet with its own MAC address and forwards the packet.
E. It replaces the source IP address of the packet with its own management IP address and forwards the packet.
F. It sends a proxy ARP request for the MAC address of 192.168.1.254.
Answer: A
NEW QUESTION 1003
Which three feature of AAA with RADIUS are true? (Choose three.)
A. It encrypts the password for transmission.
B. It integrates authorization and authentication functions.
C. It separates authorization and authentication functions.
D. It encrypts the entire transmission.
E. It secures access to endpoint devices.
F. It secures access to network devices.
Answer: ABF
NEW QUESTION 1004
Which command do you enter on a device so that users are automatically placed in enable mode after they authenticate with TACACS+?
A. aaa authorization exec default group tacacs+ if-authenticated
B. aaa authorization exec default group tacacs+ local-case
C. aaa authorization exec default group tacacs+ enable
D. aaa authentication exec default group tacacs+ if-authenticated
Answer: D
NEW QUESTION 1005
Which two statements about recovering error-disabled interface are true? (Choose two.)
A. Reloading the switch recovers it from the error-disabled state.
B. If errdisable recovery is configured, the interface is recovered automatically when the root problem is corrected.
C. Removing and reinserting network media recovers an interface from the error-disabled state.
D. Errdisable recovery is enabled by default and operates normally without additional configuration.
E. The show errdisable recovery command displays the conditions for which autorecovery is enabled.
Answer: BE
NEW QUESTION 1006
Which two configuration requirements for port security are true? (Choose two.)
A. The port must be part of a trunk.
B. Port security must be enable at the port level.
C. Port security must be enabled at the global level.
D. The port must be SPAN port.
E. The port must be part of an EtherChannel bundle.
F. The port must be in access mode.
Answer: BF
NEW QUESTION 1007
To which VLAN is a dynamic access port assigned by default?
A. None, until the VLAN membership of the port is discovered.
B. The native VLAN.
C. The same VLAN as the VLAN membership policy server.
D. VLAN 1, the default VLAN.
Answer: A
NEW QUESTION 1008
Which two statements about TACACS+ are true? (Choose two.)
A. It is a Cisco-proprietary technology.
B. It support several less-common protocol in addition to IP.
C. It encrypts only the packet header.
D. It is more reliable than RADIUS because it communicates with UDP packets.
E. It is backwards-compatible with TACACS.
F. It combines accounting and authorization functions.
Answer: AB
NEW QUESTION 1009
Which form of centralized device authentication allows each AAA feature to function separately?
A. local database
B. RADIUS
C. TACACS+
D. kerberos
Answer: C
NEW QUESTION 1010
Which command prevents all access ports on a switch from sending or receiving BPDUs?
A. spanning-tree portfast bpduguard default
B. spanning-tree bpdufilter default
C. spanning-tree bpdufilter enable
D. spanning-tree portfast bpdufilter default
Answer: D
NEW QUESTION 1011
Which two statements about configuring EtherChannel are true? (Choose two.)
A. They can be configured to passively negotiate a channel with a connected peer.
B. They can be configured with the no switchport command to place them in Layer 3 mode.
C. They can be configured to load-balancing traffic based on Layer 7 information.
D. They can be configured to operate with up to 10 links in a single channel.
E. They can be configured to send Layer 2 packets.
Answer: AB
NEW QUESTION 1012
Which two statements about UDLD aggressive mode are true? (Choose two.)
A. UDLD attempts to re-establish a downed link one time before declaring the link down.
B. UDLD message are send every 15 seconds.
C. If a unidirectional link is detected, the port state is determined by spanning tree.
D. UDLD automatically chooses the messaging interval based on the configured timers.
E. The UDLD detection timer is four times the message interval by default.
F. If a unidirectional link is detected, the port state is changed to errdisable.
Answer: BF
NEW QUESTION 1013
You are configured dynamic ARP inspection. Which command must you configure on the device to detect unexpected IP addresses in the ARP packet?
A. ip are inspection validate ip
B. ip verify source
C. ip are inspection trust
D. ip are inspection vlan
Answer: A
NEW QUESTION 1014
Which two commands enable you to determine the native VLAN that is configured on an interface? (Choose two.)
A. show interface status
B. show interfaces
C. show interface trunk
D. show running-config
E. show interface brief
Answer: CE
NEW QUESTION 1015
In a Cisco StackWise Virtual environment, which planes on the component devices are virtually combined in the common logical switch?
A. control and management only
B. control and data only
C. control, data, and management
D. management and data only
Answer: A
NEW QUESTION 1016
Which statement about Cisco StackWise is true?
A. When a new switch is added, the master switch suspends traffic forwarding until the new switch is updated with the least running configuration.
B. The stack elects a master switch and a standby switch to support rapid failover.
C. The entire stack communicates using a single management IP address.
D. If a single interconnect cable in the stack fails, the stack can continue to operate at full bandwidth.
Answer: C
NEW QUESTION 1017
In which EtherChannel mode does a port receive and respond to PAgP message without initiating EtherChannel communication?
A. desirable
B. active
C. on
D. auto
Answer: D
NEW QUESTION 1018
If all switches in a network have the same spanning-tree priority, which switch is elected as the root bridge?
A. the switch with the highest physical interface IP address
B. the switch with the lowest MAC address
C. the switch with the lowest loopback interface IP address
D. the switch with the highest MAC address
Answer: B
NEW QUESTION 1019
Which command configures all access ports on a switch to immediately enter the forwarding state when the switch is reset?
A. spanning-tree portfast bpduguard default
B. spanning-tree portfast default
C. spanning-tree portfast
D. spanning-tree portfast bpdufilter default
Answer: B
NEW QUESTION 1020
Which three responses from a RADIUS server are valid? (Choose three.)
A. CHALLENGE
B. ACKNOWLEDGE
C. UPDATE PASSWORD
D. REJECT
E. ACCEPT
F. CONFIRM
Answer: ADE
NEW QUESTION 1021
Which VTP mode must you configure on a VTP domain so that the switch with the highest VTP configuration revision number in the domain propagates VLAN information to the other switches?
A. server mode
B. transparent mode
C. off mode
D. client mode
Answer: A
NEW QUESTION 1022
……
The new Pass Leader 300-115 dumps (Jan/2019 Updated~~~1042 Q&As)!!!
The new Pass Leader 300-115 dumps (Jan/2019 Updated~~~1042 Q&As)!!!
The new Pass Leader 300-115 dumps (Jan/2019 Updated~~~1042 Q&As)!!!
Good Luck!!!
CONGRATULATIONS!!!
Dear All,
I just pass exam last few hours. Very Thanks to Digitaltut.
95% are in ROUTE_Dec_2018 (I cannot update the link, i try many time already, but u can download it in this website)
Note: I mean new question around 5 to 8, I believed that new questions are going to update more and more by CISCO. Please take exam as soon as you can, don’t miss the chance!!!!!!!!!
I got 897/1000
—-Good Luck To Everybody—-
95% are in those link: ***h*t*tp*:/*/***w*w*w.*umr*ez*en***.in.rs/cisco-ccnp-route-300-101-drag-and-drop-questions-2019**/ and ***ht*tp*://*w*w*w.***u*mr*ez*en.***in.rs***/files*/uploads/2019/01/***ROUTE_Dec_2018.pdf
It is enough to get pass. (just remove the ***)
Note: I mean new question around 5 to 8, I believed that new questions are going to update more and more by CISCO. Please take exam as soon as you can, don’t miss the chance!!!!!!!!!
I got 897/1000
@KH-CAM congraaats and well done.
Would be so kind and share the 5 to 8 new question if still remember.
Thanks,
Storm.
New question 1004 is wrong its A
How to skip enable mode password prompt.
aaa new-model
aaa authentication login default group tacacs+ local
aaa authorization exec default group tacacs+ if-authenticated
Im taking the route exam on this monday. please any one share latest dumps yo mahijini1 gmail com
It would be a great help.
Thanks
@KH-CAM
are there new labs and sims? and DNDs?
Hi,
Please share 300-101 dumps or LABS dumps.
Thanks.
could u share latest dumps link , thanks a lot
best reagrds
I just passed yesterday, I only studied most popular questions and updated question and labs in premium. It was barely enough I found about 15 new questions.
Labs
OSPF sim – the one with portland switch only difference is area is 6 and ip is 192.168.20.5
EIGRP Stub Sim same as here
EIGRP Evaluation
D&D
Answer:
A – no ip address
B – interface serial0.1 point-to-point
C – frame-relay interface-dlci 100 ppp virtual-template1
D – ppp authentication chap
————
Answer:
IPv6 Traffic Filter
+ It filters traffic on the interface level
+ It supports tagged ACLs
IPv6 Access Classes
+ It controls traffic to and from the router
+ It requires the destination address for inbound traffic to be a local address
+ It filters management traffic
———————————————-
Answer:
CoPP:
+ It protects the device against DoS attacks
+ It supports packet forwarding by reducing the load on the device
+ It uses QoS to limit the load on the device
MPP:
+ It designates the permitted management interfaces on the device
+ It is enabled only when an interface is configured
+ It requires only a single command to configure
———————————————————
Answer:
1. Auth-proxy: It returns information about hosts using proxy service
2. Commands: It returns information about individual EXEC commands and permissions associated with a privilege level.
3. Connection: It returns information about outbound communications from the network access server
4. Exec: It returns information about user EXEC terminal sessions with the network access server
5. Network: It returns information about SLIP, PPP and ARA sessions.
6. Resources: It returns information about calls that have passed and failed user authentication
best wishes to all
Someone would you pleases share me newly dump Routing 300-101. Please send for me to email : {email not allowed}. Thanks for you help
Testing Post
@James nguyen
—https—:–//——bit—-.—-ly—–/—-2QYKqTD—
remove the —
@James
it was someone else’s link i just posted as Anonymous
enjoy
Anonymous
can you share new 15 questions plz
so you say we have new questions ? please share i wanna take the exam next week …….
where new questions ?
Which two areas does OSPF send a summary route by default ? (Choose two)
A. NSSA
B. Backbone
C. Totally stubby
D. Stub
E. Normal
Is B and E correct answers?
@ospf area
correct answers are C, D
Which two areas does OSPF send a summary route by default ? (Choose two)
A. NSSA
B. Backbone
C. Totally stubby ****
D. Stub ***
E. Normal
Answer C D
GROUP Buy @ just 20$
Just passed the CCNP ROUTE exam with 950/1000. the mcq are still very the same here.
Here we go.
Get EXAM MATERIAL at below:
Copy below. Remove asteriks
g*o*o*.*g*l*/kp1zbY
I passed exam today , exam is so easy and all questions from dump , one new question is ” which values that used in VPN with vrf
1.Rd
2. Vnet tag
Lap are eigrp stup, ospf , ospf eigrp redistribution
@Kala congraats
Can you please advise if the Questions came from “https://www.digitaltut.com”
and Are the any New Questions?
Storm see questions the above
can someone please send link for digital tut question set ?
hello @NEW_HERE
I haven’t taken the ROUTE exam yet, I have it booked for a week on Monday. I’ve been going through the ROUTE_dec_2018.pdf questions which I downloaded from this site. There’s a link on the ‘ROUTE FAQs & Tips’ page, you can find a link to that page in the right hand section. The link to the pdf is just before the comments section.
The pdf has MCQs and D&Ds
I plan to lab up all the sims and purchase membership to this site.
Hope that helps.
hello @elle
please see my previous comment about where to find the ROUTE_Dec_2018.pdf on this site.
From looking at the long post that @Anonymous posted in reply to @Storm all the questions are in the pdf.
hope that helps.
@ kala , bobafett , NEW_HER , Anonymous
Thanks for the information and congraaats.
@ kala , bobafett , NEW_HER , Anonymous
Thanks for the information and congraaats.
time to get started studying for ROUTE!
i got all the files needed for revising.
For the EIGRP Evaluation are there consoles on the Routers for us to type the show commands , or
Thanks for your helo @Anymous, If you have file VCE dump, you would like share for me.
Why is no one answering me? :( Can someone please share the latest dump? I need it asap!