Share your ROUTE v2.0 Experience

someone please share the new .pdf 300-101 V23.75 with me

Hi all,

where I can find latest pdf 300-101?

help me, please

Hi guys.

These documents were shared few pages ago.
Just go there.

Good luck

Anonymous,
can you share a valid link where I can find a valid dump?
Thanks in advance

@Lechu

Q3/227

When unicast Reverse Path forwarding is confugired on an interface, which action does the interface take first when it receives a packet ?

A – it verifies that the source has valid VEF ajency
B – it checks the egress access list
C – it verifies a reverse path via the FIB to the source
D – it checks the ingress access lists

In dump is C, but should be D

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_data_urpf/configuration/xe-3s/sec-data-urpf-xe-3s-book/cfg-unicast-rpf.html

follow your link, in dump is C true

@ Question. Here are the answers.

1.How does an EVN provide end-to-end virtualization and separation of data traffic from multiple networks?
A. on the edge interface, with vnet tag
B. on the edge, with 801.q
C. on the trunk, with vnet tag
D. on the trunk, with 802.1 q

Answer: C

2. Consider this scenario. TCP traffic is blocked on port 547 between a DHCPv6 relay agent
and a DHCPv6 server that is configured for prefix delegation. Which two outcomes will
result when the relay agent is rebooted? (Choose two)
A. Routers will not obtain DHCPv6 prefixes.
B. DHCPv6 clients will be unreachable.
C. Hosts will not obtain DHCPv6 addresses.
D. The DHCPv6 relay agent will resume distributing addresses.
E. DHCPv6 address conflicts will occur on downstream clients.

Answer: AD

3. Which two statements about configuring Frame Relay point-to-multipoint connections are true? (Choose two)
A. They ignore the broadcast keyword in the frame-relay DLCI mapping.
B. They requireasd the same DLCI on each side of the link.
C. Changing a point-to-multipoint sub interface to a different type requires the interface to be deleted and recreated.
D. They require the frame-relay mapping command to be configured.
E. They require inverse ARP.

Answer: DE

——————————————

For the question about configuring Frame Relay point-to-point connections, the answers are:

– Changing a point-to-point sub interface to a different type requires the device to be reloaded.
– They use two DLCIs to communicate with multiple endpoints over the Frame Relay cloud.

All the best for exams. Please share your exam experience after fininshing the test. Thanks!

@Kani

One question came up which I cannot found in the dumps or in the MPQ, but found in the site.
Sadly I have answered it wrong. :( What do you think how much point could I lose in this…
If you can answer that I can probably answer 2 other important questions which we always discussed before.

A network engineer executes the show crypto ipsec sa command. Which three pieces of information are displayed in the output? (Choose three)
A. inbound crypto map
B. remaining key lifetime
C. path MTU
D. tagged packets
E. untagged packets
F. invalid identity packets

Answer: A B C

Hi Guys.
I will share the dumps today.
I am not in my home right now.

But the dumps were shared few pages ago. Just read all the comments.

Good luck

Digitaltut has updated DUMP file
https://www.digitaltut.com/route-questions-and-answers

About 80% questions are here. A lot of questions from section NEW (OSPF down bit, stateless/stateful DND, LLQ, new Frame Relay D&D)
I had some from old 757q, for example:
QUESTION 10
Which three TCP enhancements can be used with TCP selective acknowledgments? (Choose three)
A. header compression
B. explicit congestion notification
C. keepalive
D. time stamps
E. TCP path discovery
F. MTU window
Correct Answer: BCD
Section: Networking – Questions DAY-1

New December dump is valid to pass exam.

@ Kaktus thanks @ Router Learning still expecting your upload, can someone please convert https://www.mediafire.com/file/xhn6ran5hcqb971/ROUTE_Dec_2018.pdf to vce format.

@ Kaktus thanks @ Router Learning still expecting your upload, can someone please convert https: / / www . mediafire . com / file / xhn6ran5hcqb971/ROUTE_Dec_2018 .pdf to vce format.

@Kaktus is Digitaltut new December dump enough to pass ?

@Kaktus Thanks millions time for your help, is enough for new update and 757 dumps i will sit 17-12-2018 so what else experience you share me

Thanks all

To all!

As Kaktus said… I have said it also. Digitaltut is enough to understand and to pass, but you have to know the MPQ and the 5th update is about 80-90% of the questions, and at least once or twice must go thought the whole digitaltut (old questsions) to have the 100%…

I have done this and had 0, NULL, ZERO new question!! Pay for the premium and learn from the website… use the forum and you will be just fine.

I have done my Routing yesterday with 9xx and with that I am a CCNP now!

How to set up IP SLA to monitor jitter between the certain limits? <= (it’s jitter now, not bandwidth)
A. Timeout (not timer)
B. Frequency
C. Threshold
D. Queue-limit

Correct answer is C that same answer in PL and 757.

—————————
Q:Features of Netflow version 9? (CHOOSE TWO)
A. Cisco proprietary
B. IEEE standard
C. IETF
D. ingress/egress
E. ingress
F. egress
Answers are A&D

https :// http : // http://www.cisco. com /c/en/us/products/ios-nx-os-software/netflow-version-9/index. html
https: //www. plixer.com/ blog/scrutinizer/ netflow-version-9-egress-vs-ingress/

Congratulations @Camp

@Camp

I am premium member not enough to read Most popular and update part 5 or it’s must to read all 300-101 Category as mention in digitaltut member page they said only it’s enough for most popular and part 5 update

@ all
I have a question about the following question:
Which task must you perform to enable a point-to-point Frame Relay connection?
A. Enable inverse ARP.
B. Configure the encapsulation type.
C. Configure static address mapping.
D. Disable inverse ARP.

What is correct answer B or C?

B In normal the router interface is hdlc so to enable frame relay we change the encapsulation
in C the frame relay mapping is not need for point to point because we use physical interface other side Inverse arp is default enable but no need

To all. Soon I will stop browsing digitaltut but again.
757q and digitaltut (DECEMBER ROUTE questions) is enough to score 90-95%. I would say that just new update from digitaltut is enough to pass exam with minimum score (790). I had couple of questions (maybe 5?) that were not in Digitaltut new update.

@Shaima Kahn

Wrong forum man… this is the 300-101 not the Switching… But for information there is also enough to use digitaltut and the forum… I have done the Switching in July with this “strategy”.

@Kani

Kaktus just answered your question… MPQ and 5th update is around 90%… So you can pass with them. But to be sure and leave some chance for mistakes its better to go through on the whole website cuz there are some questions there which came back at my exam too.

@ Kani
Thanks a lot.!

@Camp @Kaktus both of you thanks i learn good people in this forum and all other.

Without @Routerider, @JJ, @Kaktus, @Kani, @Router Learning, @pjsousa, @mancert, @Networker, @Lechu, @Saji, and there are some I cant recall now the exam would have been way harder… I am here on this forum since 25th of November and I have met a lot of good people who helped each other… To be an active member of this forum makes your exam way easier…

I would like to thank you them all too, and best luck the others who will follow us discussing the questions and with that helping each other.

Since the 25th of October… not November :D

A network engineer is enabling RIPng on a new customer link. Under which configuration mode is RIPng enabled?
A. Global
B. Router
C. Interface
D. IPv6
I thanks the correct answer as “c”, but digitaltut say as “a”
@all How do you think about that?

https://www.cisco.com/c/en/us/td/docs/switches/metro/me3600x_3800x/software/release/15-4_3_S/configuration/guide/3800x3600xscg/RIPng_IPv6.pdf

Don’t forget to enable IPv6 unicast routing otherwise no routing protocol will work for IPv6.

that means i try GNS3 now when i go under interface and write IPv6 rip cisco enable
the command not executed error % RIPng: IPv6 routing is not enabled. so when I enable the ipv6 unicast-routing in global mode the under interface the RIPng can enable with out of ipv6 rip cisco in the global mode so that mean the interface is enough to enable on RIPng if already ipv6 unicast routing is enabled

for detail in this example the Interface C

https://networklessons.com/ipv6/how-to-configure-ripng-on-cisco-ios-router/
https://studfiles.net/preview/4644023/

@JJ

A network engineer is enabling RIPng on a new customer link. Under which configuration mode is RIPng enabled?
A. Global
B. Router
C. Interface
D. IPv6

RIPng is the IPv6 format of RIP protocol. We perform the initial RIPng configuration at the “Global” config mode to enable RIPng on the router.

Then we apply the RIPng configuration at the interface level.

For example:

We enable RIPng at the Global config mode:

R1(config)#ipv6 router rip process1

Then we apply the RIPng config and enable RIPng on the interface:

R1(config)#interface Ethernet 0/0
R1(config-if)#ipv6 rip process1 enable
R1(config-if)#exit
R1(config)#interface Fa 0/0
R1(config-if)#ipv6 rip process1 enable

The correct answer should be A – Global, because we enable the RIPng first at the Global level.

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_rip/configuration/xe-3s/asr1000/ip6-rip-xe.html#GUID-311EC60B-DACB-4293-BD46-F9D8B65CF740

@Networker

is cisco command some of them are mandatory to enter is sequence other are not in the global mode if you enable Ipv6 rip cisco it ok but if you go interface and enable IPv6 rip cisco enable automatically it will create the previous command function and it will write in running configuration

other side to ✔ to enable ripv6 in customer link we go interface not global mode as my opinion

@Kani

I agree it can be enabled at the interface level.

But it is always a good practice to configure/enable routing protocols at the Global config mode and inherit the configurations to the interfaces.

Again I interpret the question like this “A network engineer is enabling RIPng on a new customer link. Under which configuration mode is RIPng enabled?”. From the question, “new customer link”. So it is always recommended to enable RIPng on the Global config mode.

I refered “CBT Nuggets” and “INE” videos on this subject as well. They describe enabling RIPng at the Global config mode and then “adding” interfaces to the config.

Here is a reference from “Network Lessons” site as well: https://networklessons.com/ipv6/how-to-configure-ripng-on-cisco-ios-router/

In my opinion for a new customer link, would recommend enabling RIPng at the Global level first.

Hi guys,

Passed today 890/1000…did not get any new question. There some reworked questions though…I got a AAA D&D and i was not prepared (forgot to review that topic…my fault).

EIGRP STUB / OSPF SIM / EIGRP Evaluation SIM were there.

Good luck to you guys!

@Networker . There is statement which is in your link.

Networker
Enabling IPv6 RIP
Before You Begin
Before configuring the router to run IPv6 RIP, globally enable IPv6 using the ipv6 unicast-routing command in global configuration mode, and enable IPv6 on any interfaces on which IPv6 RIP is to be enabled.

If you want to set or change a global value, follow steps 1 and 2, and then use the optional ipv6 router ripcommand in global configuration mode.

SUMMARY STEPS
1. enable
2. configure terminal
3. ipv6 unicast-routing
4. interface type number
5. ipv6 rip name enable

@pjsousa congratulation!!

Guys, what is MPQ and the 5th update?where can I find them?

In the website you have to pay a little to be a premium member, then you have acces to the Most Popular Questions (MPQ) and the Updated ones (5th update).
It is enough to pass and that 15$ for a month membership worth every penny…

@pjsousa
Congrats from me too! :)

Congrats

Someone can send MPQ and v5 ?
lechu 21 @ poczta. wp .pl

So Spoto and MPQ it is enough ?

@pjsousa Congrats

@Capacity

Guys, @RouterRider already post the all DUMPS 1/December.

——————————————————————————-

With MultiChoice’s permission here is the link to the Q227 dump:
ht tp : // bit . ly / 2U3AxHg

And the questions which have probably faulty answers:
h ttp: // bit . ly / 2RskocJ

ht tp:/ / ww w.f iled ro ppe r.c o m /30 0-10 1v2 375

http: //goo. gl/TsS9Pq

htt p s : / /d r opme fil es . c o m/3 au h 1

——————————————————————————-
I cuold not find networking in my pc, If someone has it, please share with our friends

A special thanks for @maia @RouterRider @Kaktus @pjsouza and @DJ Config Tee

Answer me please

1-Which two protocols are required for DMVPN? (Choose two)
A. IPSec
B. PPTP
C. mGRE
D. NHRP
E. Open VPN
Answer: C D or A D

2-If you configure one router in your network with the auto-cost reference-bandwidth 100 command, which effect on the data path is true?
A. The data path remains the same for all links
B. The data path changes for 10Mbps links only
C. The data path changes for all links
D. The data path changes for 10Gbps links only
Answer: c or A

3-What is the minimum log level for the event generated when an ACL drops a packet?
A. 4
B. 5
C. 3
D. 7
E. 6
Answer: E or D

Refer to the exhibit. How can you configure a second export destination for IP address 192.168.10.1?
A. Specify a different TCP port
B. Specify a different UDP port
C. Specify a VRF
D. Configure a version 5 flow-export to the same destination
E. Specify a different flow ID
Answer: B or C

Which two options are limitations of stateful NAT64? (Choose two)
A. It is unable to route VRF traffic
B. It is unable to route multicast traffic
C. It supports FTP traffic only with an ALG
D. It supports DNS64 only
E. Layer 4 supports TCP only
Answer: A B or B E

Question 23 from MPQ

Which command do you enter to filter only routing updates that are sent through interface
GigabitEthernet0/0?

A. R1(config-if)#passive-interface GigabitEthernet0/0.
B. R1(config-router)#no passive-interface GigabitEthernet0/0
C. R1(config-router)#passive-interface GigabitEthernet0/0
D. R1(config-router)passive-interface default
E. R1(config-if)#passive-interface default
F. R1(config-router)#distribute-list 1 GigabitEthernet0/0 out

In dump is C, but in case with EIGRP or OSPF we break up the relation, so distribute list is better option . ??

Can you plz send latest dumps to adnandaudzai at gmail.com

1-Which two protocols are required for DMVPN? (Choose two)
A. IPSec
B. PPTP
C. mGRE
D. NHRP
E. Open VPN
Answer: C D or A D

2-If you configure one router in your network with the auto-cost reference-bandwidth 100 command, which effect on the data path is true?
A. The data path remains the same for all links
B. The data path changes for 10Mbps links only
C. The data path changes for all links
D. The data path changes for 10Gbps links only
Answer: c or A

3-What is the minimum log level for the event generated when an ACL drops a packet?
A. 4
B. 5
C. 3
D. 7
E. 6
Answer: E or D

4-Refer to the exhibit. How can you configure a second export destination for IP address 192.168.10.1?
A. Specify a different TCP port
B. Specify a different UDP port
C. Specify a VRF
D. Configure a version 5 flow-export to the same destination
E. Specify a different flow ID
Answer: B or C

5-Which two options are limitations of stateful NAT64? (Choose two)
A. It is unable to route VRF traffic
B. It is unable to route multicast traffic
C. It supports FTP traffic only with an ALG
D. It supports DNS64 only
E. Layer 4 supports TCP only
Answer: A B or B E

6- R1(config)#ip sla 1 R1(config-ip-sla)#icmp-echo 172.20.20.2 source-interface FastEthernet0/0 R1(config-ip-sla-echo)#timeout 5000 R1(config-ip-sla-echo)#frequency 10 R1(config-ip-sla-echo)#threshold 500 R1(config)#ip sla schedule 1 start-time now life forever R1(config)#track 10 ip sla 1 reachability R1(config)#ip route 0.0.0.0 0.0.0.0 172.20.20.2 track 10 R1(config)#no ip route 0.0.0.0 0.0.0.0 172.20.20.2 R1(config)#ip route 0.0.0.0 0.0.0.0 172.30.30.2 5
A. The source-interface is configured incorrectly
B. The destination must be 172.30.30.2 for icmp-echo
C. A route back to the R1 LAN network is missing in R2
D. The default route has wrong next hop IP address
E. The threshold value is wrong

Answer : Cd

7-Which access list used to filter upper layer protocol?
A. extended access-list
B. standard access-list
Answer: A

8-Which type of access list allows granular session filtering for upper-level protocols?
A. content-based access lists
B. context-based access lists
C. reflexive access lists
D. extended access lists
Answer: C

9-on a frame relay ,we are unable to ping the remote router,how to solve this problem?
1- dlci is active
2-dlci is unactive or deleted
3-frame relay map is configured
4-need and acl to allow ping
Answer c

@ all and ccnp ccnp
this is my opinion, please check below question!!

Refer to the exhibit.
router eigrp 65535 no auto-summary network 10.0.0.0 0.0.0.255 router ospf 1 network 192.168.5.0 0.0.0.255 area 0
passive-interface loopback0 redistribute eigrp 65535 If this configuration is applied to a device that redistributes EIGRP routes into OSPF.
which two statements about the behavior of the device are true? (Choose two)
A. EIGRP routes appear in the routing table as E2 OSPF routes
B. The device router ID is set to Loopback0 automatically
C. The device redistributes all EIGRP networks into OSPF
D. EIGRP routes appears in the routing table as N2 OSPF routes
E. The device redistributes only classful EIGRP networks into OSPF
F. EIGRP routes appears as type 3 LSAs in the OSPF database
Answer: C E -> A E
-> I thanks C & E cannot be correct answer simultaneously.

Refer to the following command.
Logging Console 7
Which option is one of the effects entering this command on a Cisco IOS router, with no additional logging configuration?
A. Debug messages can be seen on the console by enabling ―terminal monitor?
B. Debug messages are logged only on active console connections.
C. A user that is connected via SSH sees level 7 messages
D. The router can experience high CPU utilization
D -> B is more correct answer

Refer to exhibit. Which two reasons for IP SLA tracking failure are likely true? (Choose two)
A. The source-interface is configured incorrectly
B. The destination must be 172.30.30.2 for icmp-echo
C. A route back to the R1 LAN network is missing in R2
D. The default route has wrong next hop IP address
E. The threshold value is wrong
C,E -> maybe A,E

Customer enabled new link to partner using RIPng, how and where is RIPng configured?
A. router mode
B. interface mode
C. global – (config)#ipv6 router rip ―RIPNG‖
Answer: C , B is more correct answer

Which task must you perform to enable a point-to-point Frame Relay connection?
A. Enable inverse ARP.
B. Configure the encapsulation type.
C. Configure static address mapping.
D. Disable inverse ARP.
Answer: C -> B
->Inverse ARP is auto enabled by default.

Which adverse circumstance can the TTL feature prevent?
A. routing loops
B. DoS attacks
C. link saturation
D. CAM table overload
Answer: B -> A is more correct answer

A network engineer is enabling RIPng on a new customer link.
Under which configuration mode is RIPng enabled?
A. Global
B. Router
C. Interface
D. IPv6
Answer: A -> C
-> https://www.cisco.com/c/en/us/td/docs/switches/metro/me3600x_3800x/software/release/15-4_3_S/configuration/guide/3800x3600xscg/RIPng_IPv6.pdf

Which two statements about ICMP unreachable messages are true? (Choose two)
A. They are sent when a route to the destination is missing from the routing table
B. They can be enabled and disabled on a device only on a global level
C. They are sent when a destination address responds to an ARP request
D. They include the entire packet so that the source can identify the process that generated the message
E. They include a portion of the original data so that the source can identify the process that generated the message
Answer: A,C -> A,E

Company is deploying a multicast application that must be accessible between sites,
but must not be accessible outside of the organization. Based on the scoping requirements,
the multicast group address for the application will be allocated out of which range?
A. FF00:/16
B. FF0E:/16
C. FF02:/16
D. FF08:/16
Answer: C -> D
-> FF02 is for link-local multicast and FF08 is for organization local multicast.

When OSPF is forming an adjacency, in which state does the actual exchange of the information
in the link-state database occur?
A. INIT
B. loading
C. exstart
D. exchange
Answer: C -> B

In which scenario can asymmetric routing occur?
A. active/active firewall setup
B. single path in and out of the network.
C. active/standby firewall setup
D. redundant routers running VRRP
Answer: D -> A
-> VRRP works as Active/Standby

Consider this scenario. TCP traffic is blocked on port 547 between a DHCPv6 relay agent
and a DHCPv6 server that is configured for prefix delegation.
Which two outcomes will result when the relay agent is rebooted? (Choose two)
A. Routers will not obtain DHCPv6 prefixes.
B. DHCPv6 clients will be unreachable.
C. Hosts will not obtain DHCPv6 addresses.
D. The DHCPv6 relay agent will resume distributing addresses.
E. DHCPv6 address conflicts will occur on downstream clients.
Answer: A D
-> if the dhcpv6 packets are blocked then A,C, if not D, ??

Refer in the exhibit.
interface FastEthernet0/0
ip helper-address 192.168.145.5

A packet capture indicates that the router is not forwarding the DHCP packets
that it receives on interface FastEthernet0/0.
Which command needs to be entered in global configuration mode to resolve this issue?
A. ip helper-address
B. ip DHCP relay
C. service DHCP
D. ip forward-protocol
Answer: B -> C
-> The ip DHCP relay command have to configured on interface mode because ip helper-address is configured on an interface.
therefore i think C. service DHCP is correct answer.

Which two statements about DMVPN are true? (Choose two)
A. IPsec encryption not supported with statically addressed spokes
B. It requires full-mesh connectivity on the network
C. It uses NHRP to create a mapping database of spoke addresses
D. Multicast traffic is not supported
E. It supports dynamic addresses for spokes in a hub-and-spoke VPN topology

Answer: A,C -> C,E

The question is in digitaltut updated on 5th DEC!

urgent question
is the tap working in the lap
pleaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaase answer

is there any VCE file for new update from this site ??
pls help

tab is working in labs in exam

Anonymous is it working