Share your ROUTE v2.0 Experience

Yap Q52/277 for me is BE also
https://sites.google.com/site/amitsciscozone/home/ppp/ppp-over-ethernet

@ricokiu

have you remember new question please post

Q1/227 New SPOTO

Frame Relay statements
Answer A is wrong , Do you need restart a device when type of subinterface was changed ?

yes you have to reload:

No, after a specific type of subinterface is created, it cannot be changed without a reload. For example, you cannot create a multipoint subinterface Serial0.2, and change it to point-to-point. To change it, delete the existing subinterface and reload the router or create another subinterface. When a subinterface is configured, an interface descriptor block (IDB) is defined by the Cisco IOS® Software. IDBs defined for subinterfaces cannot be changed without a reload. Subinterfaces that are deleted with the no interface command are shown as deleted by issuing the show ip interface brief command.

@Lechu
“Once you create a specific type of subinterface, you cannot change it without reloading the router. For example, you cannot create a multipoint subinterface serial0.2 and then change it to point-to-point. To change it, you need to either reload the router or create another subinterface. This is the way the Frame Relay code works in Cisco IOS software.”
http: // www . ciscopress . com /articles/article.asp?p=170741&seqNum=5

Q173/227 New Spoto

DMVPN Statements

Asnwers AC
Answer A is incorrect. IPsec is supported

Correct CE

Guys, thank you for link.
Indeed O_O

Been studying the 227 Q bank along with the 190Q bank I received else where. I have my test scheduled this week, and will report back. Appreciate the proactive-ness on this site..

@all

I passed the Switch and troubleshooting already. Out of the three sites, the troubleshooting (networktut) is the most updated (primarily because people take troubleshooting to renew their CCNP tracks)

Forgot to put my alias, that is my comment above…

@all

if the 190Q bank is valid, I will also share that one as well.. This bank that I have seems to have all of the other questions not seen on the 757Q and 227Q bank..

Hi All,

Are the questions on digitaltut premium enough to pass the exam ?

When unicast reverse path forwarding is configured on an interface, which action does the interface take first
when it receives a packet?
A. it verifies that the source has a valid VEF adjacency.
B. It checks the egress access lists.
C. it verifies a reverse path via the FIB to the source.
D. It checks the ingress access lists.

which option is correct?

@ aussie mate

read the blog’s.. its been a collaborative effort. Start from page 257

In my opinion if you have unnecessary money try it.
I have an access, but it doesn’t give me any plus information.
There are a lot of faulty answer and they don’t refresh the question after last change.
I think this forum is more helpful.

@DJ Config Tee
I took my exam today.
If you would like, I can confirm your dump.

@routerider can you please check pass4sure new demo 10 question i believe they are new and in your exam also , after checking please advice

@RouteRider

Your email?

And what specific sims, labs and DnDs did you have?

The source of this dump was the same source I got my switch dump from (124Q test bank), and 90 percent of those questions came from that one as well..

@Anonymous, can you paste the pass4sure new demo 10 questions here?

@bobster
We need to download it from pass4sure site it is a software where they are providing 10 update questions you can google it

Hi Guys,

I’m currently learning for my retake of failed exam (i got 769 points – so basically two mistakes from passing – i’ve been taking it on 23 November) – had about 50-50 questions from digitaltul most popular questions and new questions (for example question what is vrf-lite) – i know i made some mistakes in questions from this site (at least 4 questions) so i know that i was able to answer some of the new questions correctly. For the labs they were exactly the same as here. I got EIGRP Evaluation, Eigrp Stub and Virtual-Link. Looking at 227q dump i got a lot of questions from there on exam.

Also i got a strange question about allowing user to log to router only to show logs and then dropping his connection and which command was the correct logging action. has anyone saw this?

@DJ Config Tee
routerider01 at gmail dot com
Lab: EIGRP Stub, OSPF
Sim: EIGRP Evualation
D&D: COPP and MPP, IPv6 router security features, Frame relay with PPP (new), AAA accounting types (left side same, but right side totally else as in the dump)

Guys i have question,

In Q186 from 227q (segment 7 i think)
Which configuration always block OUTBOUND web traffic on Saturdays and sundays between 1:00 and 11:59

I saw explanation but isn’t “correct” answer also wrong? I mean it’s for ip access-group 102 in – should it be out? Or it does not matter? Because i’m not quite sure about this. (i know that the other periodic answer has UDP port and that’s wrong)

Also there is a mistake in question 189 from segment 7 in 227q

Correct answer would be: inside global and outside local, and provided explanation link also states that there are four address types in NAT

Inside Local
Inside Global
Outside Local
Outside Global

https://www.cisco.com/c/en/us/support/docs/ip/network-address-translation-nat/4606-8.html#defall

Hello Guys am taking my exam on the 17th
which labs are on the exam

b i t . d o / eBknG

ignore above ” b i t . d o / eBknG “

@RouteRider
Does D&D about “Frame relay with PPP” relate the PPP Frame Relay Format Descriptions as blow?

Field -> Description
Flag -> A single byte that indicates the beginning or end of a frame.
Address ->A two-byte field that indicates the logical connection that maps to the physical channel; the DLCI.
Control -> A single byte that calls for transmission of user data. PPP over Frame Relay uses a value of 0X03, which indicates that the frame is an unnumbered information (UI) frame.
NLPID ->Network layer protocol ID, which is a single byte that uniquely identifies a PPP packet to Frame Relay.
PPP protocol -> Identifies the PPP packet type.

@RouteRider
sorry!
Is D&D about “Frame relay with PPP” related the PPP Frame Relay Format Descriptions as blow?

@RouteRider remember any D&D questions?

Passed yesterday with 9xx/1000
227 dump is valid 80% 757 valid for D&D.

Simulations
1)-IPV6 Virtual-Link: it the same from this website. Most of the dumps says you need to remove area 54 on router 3, which i did and i couldn’t see the loopback interface of R4 on R3. I had to reconfigure back area 54 on R3 and add area 11 on R2 and R3. R1 was able to see loopback interface of R4. You need to troubleshoot more to get it correct.

2)- EIGRP Stub: it the same from this website, but you need to double check if the summary of 2 subnets were created on R3.

M&C
41 question from 227

D&D
4 from 575

Simlets
EIGRP from this website 4 questions.

Good Luck Guys!!!

@RouteRider

I agree Cisco has changed the test about 30 percent of the questions are new. Do you remember any new questions?

@mr.black congratulation!!, where can i get the 757 dump ?

please share the dump chjhnav @ gmail . com !!

Thank You @JJ

Check your Email!!!

@mr.black

could u please elaborate on the new questions/topics? Did u get any question u havent seen at all in any dump?

Thanks and congrats!

Thank you@Pjsousa

There was no new question, all the M&C questions come from 227 for multiple choices. 757 doesn’t cover all the M&C question but it covers the D&D.

Some of the D&D was:
Loose mode and Strict mode
the one with hub,mGRE, NHRP, spoke and NAT64 thats all i cauld remember.

@mr.black
Thanks a lot !!!!

Valid dumps q227 here for dl http: //goo. gl/TsS9Pq
no fake s**it

what is q277 pleaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaase exam tomorrow

impossible to study757q in a short time. I study 227q and I go for the exam

Dear Guys

i pass the exam today score 800 just pass.
please guys don’t depend on dumps because dumps are not stable now from spoto 227 + 757Q i get only 30% question , rest all are very new, just wait for more 2 weeks to get stable.

labs : eigrp stub , ospf different process id 43 and area 32 ip address changed
Simulation : ospf
Dnds : point to point frame relay , Gre features (some wording changed), accounting acl (wording changed), Copp &MPP same as dumps

MCQ : i cannot remember because i am in shock each and every question looks very new please thus who are depending on dumps , they will waste there money

@JJ
No it was an other. Command list with four empty space and six choice opportunity.

send me Q575 on abdiqanipd @ gmail com

marco link to download 227q is not working i.e. http: //goo. gl/TsS9Pq

where can i get the 757 dump ?

j o t a l o p z @ h o t m a i l . c o m

thanks

Item 9 of 227
Which criterion does the BGP maximum paths feature use for load balancing?
A. MED
B. local preference
C. weight
D. router ID

Surpise ************** ANSWER IS D … why Because BGP load balancing can occur after the BGP path selection step 10 (IGP metrice). it uses the path with lowest Router-ID
http: // dept-info.labri.fr /~magoni /rvep /DOC-BGP-DECISION.pdf
MED, Local preference & Weight metrics already been used for the best path selection before it comes to load sharing. BGP by default it select the single best path.

What questions have come out of 757q, does anyone remember?

@Kamati really?

Only 30% from all files?

@saji,

are u sure?!

Hi @mr.black,

Congratulations! May I also have the copy of dumps 227 and 757.
Planing to take the exam this year.
Thank you.

agarciaccna @ gmail . com