Share your ROUTE v2.0 Experience

@spotto
Will pay for the 227/248 dumps.
Can you mail please? And payment details.
Thanks in advance.
Would be really really grateful.
Best regards
J.

Please stop asking for the q227 dumps, RouteRider already shared them on the 1st of December, you can still find his comment with the links on (currently) page 260.

Guys, @RouterRider already post the DUMPS 1/December.

With MultiChoice’s permission here is the link to the Q227 dump:
http : // bit . ly / 2U3AxHg

And the questions which have probably faulty answers:
http: // bit . ly / 2RskocJ

Please, help us to validate it and stop asking for the dumps.

@Anonymous, this question has been discussed here several times.

B is not valid because it denys udp 80 instead of tcp 80 (HTTP).

5/27

A is the correct answer as http and https is TCP traffic!
C – wrong time
D – misstype and “absolute”
B – “udp any any eq 80” which is not HTTP

@Routerride

I agree with you C D

explanation

https://www.plixer.com/blog/scrutinizer/netflow-version-9-egress-vs-ingress/

@Routerrider @pjsousa

if you want any software for making lab in gns3 i can share wiyh you multple software (ASA , Acs-server,sophos,fortigate,forticlient,cisco vpn client,cisco iou,asdm…)

I think the follow answer is wrong.

What do you think?

**ACL**
reflexive – must be named
standard – range 1300-1399
extended – telnet … ->>> dynamic – telnet
time-based – access to device at certain times
dynamic – closest to device ->>> extended – closest to device.

2/227

I have seen that somebody here wrote as an answer D instead of the given A.

Can somebody confirm the correct answer with some explanation?

@camp, regarding 2/227

After investigating, i think the correct answer is D – Provider Edge despite solution showing A.

My opinion is fundamented by this cisco paper: https://www.cisco.com/en/US/technologies/tk648/tk362/tk920/technologies_white_paper0900aecd8017f8c9.html

“[…]Dedicated routers are most appropriate when the deployment plan calls for the operations to be sourced from the edge of the core network (ie: Provider Edge [PE]) location in a Service Provider network. The Cisco 1700, 1800, 2600, 2800, 3600, 3700, 3800 and 7200 Series Routers are frequently used as dedicated routers.”

Using Cisco IOS IP SLAs to Measure Network Performance
You can use IP SLAs to monitor the performance between any area in the network—core, distribution, and edge.

https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/12-/54sg/configuration/guide/config/swipsla.html

@Balha

Please share the software’s here in site so every one will get benefit as a link

Thank you

Guys , my exam in 2 days please give me any suggestion ,

after exam i will updated all question here

what i already studied : 1) spoto227 dumps, labs&simulation dnds, 195q and 757q

@JJ

Q 40/227
D&D ACL

standard – range 1300-1399
time-based – access to device at certain times
reflexive – must be named
dynamic – telnet
extended – closest to device

I couldnt found any problem here. For me it looks good.

@Routerider @Balha @pjsousa
Please suggest me for below qusestion
Here are the questions which i have doubts because every body have its own opinion answers: SPOTO File dumps
2/227=
3/227=
18/227=
64/227=
78/100=
80/227=
90/227=
99/227=
120/227=
124/227=
128/227=
——————-
1st segment
——————-
10/100=
28/100=
64/227=
68/227=
————————
2nd 100q segment
————————
10/100=
28/100=
40/100=
62/100=
88/100=
91/100=
14/27=
18/27=

From Soto: Item 44 of 227 (Exam B, Q82)

The correct answer should have been C), specify a different UDP port, although with a VRF you can use the same destination IP, but that will be in another network with a different routing table, which means the destination host will be different as well.

It gives you a morning, but it accepts a different port number:

R1(config)#do sh ver | inc IOS
Cisco IOS Software, 7200 Software (C7200-ADVENTERPRISEK9-M), Version 15.2(4)S7, RELEASE SOFTWARE (fc4)
R1(config)#do sh run | inc ip flow-
ip flow-export version 9
ip flow-export destination 1.1.1.1 50000
R1(config)#ip flow-export destination 1.1.1.1 50001
%Warning: Second destination address is the same as previous address 1.1.1.1
R1(config)#do sh run | inc ip flow-
ip flow-export version 9
ip flow-export destination 1.1.1.1 50000
ip flow-export destination 1.1.1.1 50001

anyone got vce for 227

@charles

have a look at this https://www.cisco.com/c/en/us/td/docs/ios/12_0s/feature/guide/12s_mdnf.html#wp1023091

Section: Configuring Multiple NetFlow Export Destinations to a Router

“Note Do not enter the same ip address twice. However, entering two different ip addresses with the same udp port number is configurable.”….

@pjsousa
Multiple NetFlow Export Destinations on an Aggregation Cache Example
The following example, enables the exporting of information from the NetFlow aggregation cache:
ip flow-aggregation cache destination-prefix
export destination 192.168.10.1 9991
export destination 192.168.10.1 1999
https: // www . cisco . com /c/en/us/td/docs/ios/12_0s/feature/guide/12s_mdnf.html#wp1015440

@Routerider @Charles,

So the question is about the specific ip flow-export command and regarding that i think we cannot export twice using the same ip address. I see this ip flow-aggregation as a workaround that is not mentioned in any solution.

@pjsousa
“Multiple Export Destinations
If the version of Cisco IOS that you have installed on your networking device supports the NetFlow Multiple Export Destinations feature, you can configure your networking device to export NetFlow data to a maximum of 2 export destinations (collectors) per cache (main and aggregation caches), using any combination of UDP and SCTP as the transport protocol for the destinations. A destination is identified by a unique combination of hostname or IP address and port number or port type.”

Please attention to the last sentence (and, or words). I think the same IP addresses with distinct port numbers individually identify the destinations.

@pjsouse
It is version9 and it is the key!

What Is A Flow?
A flow is identified as a unidirectional stream of packets between a given source and destination—both defined by a network-layer IP address and transport-layer source and destination port numbers. Specifically, a flow is identified as the combination of the following seven key fields:

•Source IP address

•Destination IP address

•Source port number

•Destination port number

•Layer 3 protocol type

•ToS byte

•Input logical interface (ifIndex)

These seven key fields define a unique flow. If a flow has one different field than another flow, then it is considered a new flow. A flow contains other accounting fields (such as the AS number in the NetFlow export Version 5 flow format) that depend on the version record format that you configure for export. Flows are processed in a NetFlow cache.

https: // www .cisco .com /en/US/products/sw/netmgtsw/ps1964/products_implementation_design_guide09186a00800d6a11.html

when is your next exam- who is writing this week?

Hi

for the person who took the exam recently; does the questions came from the 227 dump

thank you

Hi guys, here you can get valid dump q227 (.pdf), no spam etc…
https:// goo.gl/ TsS9Pq

@ Marco,
the pdf file is corrupted, couldn’t download though

@ Marco, pdf file is corrupted , could you please check it ?

http: // umrezen.in.rs/Cisco%20Route_300-101-Q227_dump.pdf

Unable to upload file

need valid dumps

can anybody update please

@Routerider @Balha @pjsousa

Please suggest me for below qusestion
Here are the questions which i have doubts because every body have its own opinion answers: SPOTO File dumps
2/227=
3/227=
18/227=
64/227=
78/100=
80/227=
90/227=
99/227=
120/227=
124/227=
128/227=
——————-
1st segment
——————-
10/100=
28/100=
64/227=
68/227=
————————
2nd 100q segment
————————
10/100=
28/100=
40/100=
62/100=
88/100=
91/100=
14/27=
18/27=

@Routerider @Balha @pjsousa
guys for above i just need alphabet ab or c like that.

Pleaseeeeeeeeeeee i have exam on thusday.. after i will updated all details here.

when is your next exam- who is writing this week?

for the person who took the exam recently; does the questions came from the 227 dump

thank you

lets comppare to 227 dump and share ideas and questions

@Kamati all question , suggestion and answer are here see the older post

@ balha ,

i already revised but i see @routerider and @pjsousa have different opinions in some questions
@balha i already prepared Vce file for Spoto227 , just i need right answers for above i will upload the link here,

any one who will provide above answer i will send him vce spoto file and my exam experience just i need letters a or b or c to arrange in vce file ok

waiting to update VCE file guys

@Anonymous ok

we need to make sure answers are accurate..some can post then we will review before vcefile complete, even-tho some like pdf

Guys please provide accurate answers , one time we will finish the job for vce file,

Once every one statisfy i will adjust the answers

What are 2 protocols used for user with authentication on network device? (Choose two)
A. CHAP
B. Radius
C. 802.1x
D. PAP
E. TACACS+

Somebody wrote the correct answers are B and E, but I think the A and D are good. RADIUS and TACACS+ not only an authentication protocol, however PAP and CHAP are authentication protocol both of them.

Thanks @routerider for the 227q. Does anyone have 248q?

Here you can download valid damp q227 in PDF. It is not fake, spam etc… enjoy

https:// goo.gl/ TsS9Pq

@networkc2020

It was Maya’s and friend’s work, not me…

@Marco; Thanks but this link is corrupted. could you please provide new link?

@routerrider is A$ D

which criteria does the BGP maximum paths feature use for load balancing?
A. local preference
B. weight
C.MED
D. router ID

answer? guys..please correct ones only

Here

www. umrezen.in. rs/ cisco-route-300-101-q227_dump/

@RouteRider it would be A & D if the question mentioned PPP.

which criteria does the BGP maximum paths feature use for load balancing?
A. local preference
B. weight
C.MED
D. router ID

answer? g

You have to understand that this site, digitaltut , and current dumps will give you about 70 percent of the questions because Cisco has added about 30 percent of new questions which I have not been to find on any dump. You need to know the new questions in order to pass the test.

@227

what edit is that?