Share your ROUTE v2.0 Experience

@thanks Dexter :)

All the old folks who passed are not here anymore.. they really don’t care .

I passed exam today with 9XX. I didn’t see any new questions. All questions came from procyber 1.5. Good luck.

If you studied from books or videos, then studied from dumps, you could easily pass.

@44444
congrats , which labs you get in the exam

Hello guys,

I have passed before 1 hour with more than 900. I will write what I remember:

1. All question are from procyber 1.5 and fewmore questions from here.

2. Drag and drop were also from procyber 7-8 questions.

3. LAbs- OSPF EIGRP Eval, PBR. REdistribution, OSPF SIm

OSPF sim was the same different area and process ID:

OSPF ID -17
OSPF Area 37
Different Router names Indianapolis and I forgot the other one

On Indianapolis

# router ospf 14
# network 192.168.17.4 0.0.0.3 area 37
# area 37 stub no-summary

On the left router:
# router ospf 14
# network 192.168.17.4 0.0.0.3 area 37
# area 37 stub

This is for the middle Router which was Indy.

Be carefull with commands. Some of them doesn’t work with auto-complete(tab). Type them and if you have an error just delete it and type it again. Don’t panic!

Other than that all other Labs are the same just different IPs. If you know your stuff you will be ok.

Personal note: This cert will open a lot of chances for new jobs but you must know your stuff. If you go on interview and they ask you something you should know everything. That’s why read the book first. Don’t jump directly on the questions trying to memories everything.
I was studying 3 weeks including book, labs and procyber stuff. Every day i made those 477 questions from his lab. Tha’ts mean 21 days x 477 questions =10.017 question for passing this.

Good luck to all of you.

@Metallica
congrats
in ospf Sim
did you configure the right router with new OSPF process ID

@nino,
OSPF-EIGRP Evaluation, PBR sim, EIGRP OSPF Redistribution Sim, OSPF Sim.

In ospf sim, there was a serial link between r2 and r4. So i used eigrp distance 90 – 105 command.
Also after this command I checked the route table and if there is a serial link we have to use this command

@Metallica
if you try your configuration on the GNS3 lab the ping will failure

I wrote wrong. I mentioned about redistribution sim in upper message.

In ospf sim I could configure ospf process id. It was 88 :)

@44444

i ask For OSPF sim not eigrp ospf redistribution sim

OSPF process ID 88 that was the one already configured on the routers or the requested inthe question

requested in the question. I looked the configurations but they didn’t show it in left side touter too. Also there is no permission to use some show commands in the left side router. But it was very clearly in the question

Nino Process ID and area number must be the same. In my case ID was 17 and area was 37.

router ospf 17
network 192.168.17.4 0.0.0.3 area 37 <-this commands should be on the middle and left router

But area 37 stub no summary <- only on the middle

and area 37 stub <- only on the left

don't forget copy run config command !

HI Metallica & 4444,

Congratulations on passing the exam.

I am appearing for my exam in 10 days.

Can you please share procyber 1.5 with us?

Your help will be much appreciated.

Thanks

Lunchii there are a lot of links in previous pages.
Please search them.

@4444

Can you please share procyber pdf?

{email not allowed} (remove _)

@4444

Can you please share procyber pdf

udaralh @ gmail . com (remove space)

@CCNPdip

u have procyber pdf.
please share
my exam is next tusday
please help

udaralh @ gmail . com (remove space)

can some one please tell me where to find the labs. procyber doesnt have any of them.

thanks

@Sompret
from where did you get this dumps?

@Netcazy

u have procyber pdf.
please share
udaralh @ gmail . com (remove space)

can somebody send me “procyber 1.5”?
my email : yamichan1603 @ gmail dot com
thanks so much

congrats

Failed with 750.

OSPF-EIGRP lab with FastEthernet links
EIGRP sim
OSPF Sim
PBR lab

I got 52% on the VPN section so I guess I got some multiple choice questions wrong, going to reschedule in 2 weeks.

Are all the exams Sims all covered on the lab-sim page on this website or is there another resource?
https://www.digitaltut.com/category/route-300-101/lab-sim

procyber 1.5 its me is valid. many MCQ and DnD. Concentrate on 25% of the questions are DMVPN, ip sla. Labs are the same: OSPF-EIGRP Evaluation, PBR sim, EIGRP OSPF Redistribution Sim, OSPF Sim.

Thanks alot proker!

I Passed the exam with 8xx!!! Thanks to all for your valuable contributions. You guys are the best! Like poksaid, procyber 1.5 its me is still very valid.

1. Concentrate on 25% of the questions are DMVPN, ip sla.
2. i have about 7-8 Drag and drop. they were all from procyber.
3. Labs are the same: OSPF-EIGRP Evaluation, PBR sim, EIGRP OSPF Redistribution Sim, OSPF Sim.
Guys, if you want to pass this exam, try and write it this year, it might be reviewed by January 2018.
Stop being lazy by asking for dumps to be sent to you. look for it, it’s here couple of pages back.

All the best, thank you very much Digitaltut.

CCNP_Recertifie

Congrats!!

Are all the labs and sims were the same? can you please point what to be aware of in the labs and sims?

Joe.

@All

I see that people who went to the exam point out that the serial link in the OSPF Evaluation Sim is Fast Ethernet. what is the solution in this case? any different parameters?

Joe.

@All

Anyone can share the labs and the Cisco images? something is wrong with the one i have downloaded and its showing me different information that the labs here.

Joe.

@Joe
1. in my exams, in the OSPF Evaluation sim, R1-R3 was a FastEthernet while the R2-R3 link was a Serial link. But the question says “what is the OSPF timers for the link btw R2-R3”. just understand how they arrive at the answers in the Lab here on Digitaltut. It’s very simple.
2. Beware of the EIGRP Evaluation Sim, “Show IP EIGRP Topology” doesn’t work. You will be required to find the advertised distance for the network 192.168.46.0 (yours might be different) on R1. Use “show IP route” on R2; the METRIC on R2 to network 192.168.46.0=ADVITSED DISTANCE on R1. Meaning, R2 will tell R1 that it cost it 333056(for example, pls pay attention to the value on the exam) to get to network 192.168.46.0. R1 will store this value as its ADVERTISED distance to 192.168.46.0
3. Many Multiple Choice Questions’ Answers have been re-ordered. ensure u understand the question and commit the answers to memory
4. Make sure you memorize all the Drang & Drops. You will see many of them on the exam

All the best guys!!

CCNP_Recertified

Is it possible we can speak in private?
Joe.

@ Joe, i am sorry, i can’t give any personal information/contact on this platform…you can ask any question on this platform, i will be glad to assist.

@Mac or anybody who can share!

Can you share A+ VCE Android based tool please.

Thanks

Moh cab 2003 at ya hoo dot c o m

What is the answer to the following?

Consider this scenario. TCP traffic is blocked on port 547 between a DHCPv6 relay agent and a DHCPv6 server that is configured for prefix delegation. Which two outcome will result when the relay agent is rebooted? (Choose two)

A. Routers will not obtain DHCPv6 Prefixes
B. DHCPv6 clients will be unreachable
C. Hosts will not obtain DHCPv6 addresses
D. The DHCPv6 relay agent will resume distributing addresses
E. DHCPv6 address conflicts will occur on downstream clients.

Answer AB?

What prevents the default route from being removed when IP SLA state goes down or fails?
A. The destination must be 172.30.30.2 for icmp-echo
B. the threshold value is wrong
C. missing track feature on default static route command
D. xxxxxxx

This one I don’t even know where to begin so if anyone has the correct question or choices and the answer please chare.

What are two limitations when in use of NPTv6 for IPV6 vs IPV6 Address translation?
A.stateful address translation
B.a limit of 32 1-to-1 translations
C.lack of overloading functionality
D.identify all interfaces NAT inside or outside
E.1-to-1 prefix rewrite
F.mismatched prefix allocations

Answer CE?

Which two statements about configuring Frame Relay point-to-multipoint
connections are true? (Choose two)
A.They ignore the broadcast keyword in the frame-relay DLCI mapping.
B.They require the same DLCI on each side of the link.
C.Changing a point-to-multipoint sub interface to a different type requires the interface to be deleted and recreated
D.They require the frame-relay mapping command to be configured
E.They require inverse ARP.

Answer CD?

Any help is appreciated….Thanks in advance

@ Jigre66

Google is your best friend, that is how I found it.

Finally! I passed! 9xx

Thanks guys! Happy holidays!

Review the vpn category… dumps have incorrect answers.. got the lowest rating there.. but 9xx is already a high score

Il send what i remember but ill take a rest for now hehe

@Kimbie
did you get the exam today , also is it me 1.5 still valid

@Kimbie
Please share your dump.
I want to pass router exam.

Hi All,
please help me regarding D&D’s …………….. please

CCNP_Recertified

Thanks for the info. besides the OSPF and EIGRP eva are there any points i need to be aware of in the exam? i saw people mentioned about the EIGRP and OSPF distribution have a look: also can you please share the GNS labs& cisco router images & latest VCE file?

The below config is correct just note 2 things:

1) Portland will likely be a different name and
2) The Process ID will likely be different

Portland#configure terminal
Portland(config)#router ospf 74
Portland(config-router)#network 192.168.4.4 0.0.0.3 area 1
Portland(config-router)#area 1 stub
Portland(config-router)#end
Portland#copy running-config startup-config

The below config is correct just note 2 things:

1) Amani will likely be a different name and
2) The Process ID will likely be different

Amani#configure terminal
Amani(config)#router ospf 1
Amani(config-router)#network 192.168.4.4 0.0.0.3 area 1
Amani(config-router)#area 1 stub no-summary
Amani(config-router)#end
Amani#copy running-config startup-config

You shouldn’t have to replace anything, just add in commands to those 2 routers. The loopback router (far right router) you don’t touch.

Good Thing I read this page!

So Cisco suddenly change the EIGRP SIM to OSPF Sim! Thanks for the heads up!

Hi Joe,

Thanks for the input. Good thing I check the comment section, I am currently finalizing my studies which include EIGRP Stub Simulator but it was replaced by OSPF Sim

So the Labs are
OSPF/EIGRP Redis
OSPF Sim
PBR
OSPF Eval
EIGRP Eval

@ADRIAN
the OSPF Sim is the lab into the exam from long time not EIGRP sim

@Nino

It is? I am studying CCNP Route for 2 months and previously around Nov the lab includes EIGRP Stub.

Thanks for the info

who can share valid dumps??plz