Share your ROUTE v2.0 Experience

@Finish
These all questions are in the Q757 networking
Am I right?

@genius It is possible granting that you are familiar with VRFs. In some of the questions and if you read the answers, you can deduce the possible ones by the process of elimination. Can’t really remember what the questions were because I was concentrating more on picking the right answers. Score was 92X / 1K

Is 198 questions still valid? Or are we going to wait for new dumps

Where can I get a copy of the most accurate dump for CCNP Route? thanks!

Hello ,

Please, can someone share “Last dumps” of “pass4sure'” i sow that they update their site for last dump 08/11/2018 , thx to all and good luck for all

Hi!!
I have PASSED!!! yeah!!! 922 marks.
Labs: EIGRP STUB, EIGRP EVAL, PBR.
New DnD about Frame Relay LMI.
MCQ:
– What…show ip flow export?
– top talkers
– export interface config
– local status & statistics
* sent status & statistics

What … IPV6 Neighbor Discovery protocol replace of IPV4?
– CDP
* ARP
– ICMP
– IGMP

Router IOS connected Windows syslog server do not function. What is the reason?
* firewall is blocking … UDP port 514
– firewall is blocking … IP prot num 514
– firewall is blocking … TCP port 514
– firewall is blocking … UDP port 512

What … snmp-server enable traps & snmp-server host 192… traps version 2c public …?
* to allow …192.. to access syslog…
– to collect info abodwut system network management
– to allow private communication between router & host
– to disable all SNMP info on the system

BGP topology and configuration: Why fails eBGP neighbor?
* config update-sxource…
– change ebgp-multihop value to 1
– replace maximum-paths eibgp 4 … with maximum-paths ibgp 4 import 2
– add no syncronization statement at the end of the config

I will go for some beers hehehe yeah!!!
thank you to all of you! See you soon at Tshoot!!

Expanding off potential new question where people are talking about [PADO/PADI] — this refers to PPPoE:

PPPoE requires certain signals and information to establish, accept, control and terminate the session. The basic signalling is shown below.

A PADI (PPPoE Active Discovery Initiation) broadcast signal is sent by the host to the remote devices.

A PADO (PPPoE Active Discovery Offer) signal is sent by the remote device back to the host.

A PADR (PPPoE Active Discovery Request) unicast signal is sent by the host to the remote device.

A PADS (PPPoE Active Discovery Session-Confirmation) is sent by the remote device back to the host.

A PADT (PPPoE Active Discovery Terminate) signal is sent to terminate a PPPoE session. It is the proper way to terminate a session but isas not the actual cause for the termination. The cause may be a simple timeout, a manual request by either end, or an out of spec line condition.

Labs:
1. EIGRP-OSPF redistribution with FastEthernet link between R2 and R3. “distance eigrp 90 105” command under EIGRP on R2 is needed.
2. Policy based routing, same with the dumps
3. OSPF
4. No EIGRP nor OSPF evaluation for me

New DND:
1. Search for the definition of add regisration, global addressing, multicastion, simple route (not sure)
2. DMVPN features about hub, spoke, mGRE, NHRP

New questions:
1. Migration of protocols: Changing of administrative distance (AD), redistribution
2. SNMPV v2c use for authentication: Community String
3. Best IP SLA deployment cycle: Baseline Network Performance, Understand Network Performance Baseline, Quantify Results, Fine Tune and Optimize
4. What are true about the statement above? Statement shows ip nat source inside configuration for private ip 10.0.0.0 /27, then it will be natted to pool of public IP address with /27 subnet as well.
I forgot the choices but you can answer it if you fully understand how nat works.
5. IPV6 EIGRP features: scaling, partial updates
6. Question about PPPoE signaling, choose 2: Read about PADI/PADO/PADR/PADS/PADT and its meaning.
7. Netflow version 9 question: IETF standard, ingress/egress
8. Security level supported for all SNMP version. Not sure about my answer for this one.

Overall, I would say that Dexter dussdamps is still valid. Just understand the concept behind each question. Study the labs and master the drag and drop.
For the new questions, looks like it will show on every exam takers based on my observation. Study it.ad

@Anonymous
Most of the questions/DND are in 750q from nettwwoorrkking file.

sharing 300-101 exam questions http://certifychat.com/threads/300-101-dumps-pdf-2018.15033/ Download and prepare

@Kaktus Do you think that by learning all the 757 Q you can pass the exam?

@Elvis
To be honest I think I would pass the exam if I hadn’t reschedule it. There are no new dumps so I am studying on my own (from book How to master CCNP route and from dumps from nettwwoorrkkiinng)

@Kaktus

We were unlucky. I wanted to do it Friday 02 but the test center had no availability. So I went Monday and all the questions have changed. I had to pass it because I had the 300-115 exam due. Now I have to give that back too. I just missed the routing to become CCNP:(

Hi all,
I passed today…I studied from older dumps and I had maybe half questions from the older dumps and then new questions…labs were the same…

I have found a dnd about NAT64 NPTv6 characteristics
on left there is:
-Modifies IP IP Header in Transit
-Maps one IPv6 address prefix to another IPv6 prefix
-Uses Network-specific prefix
-Modifies session during translation

On Left there is:
NAT64
– Target 1
– Target 2

NPTv6
– Target 3
– Target 4

and the answer to it is:
NAT64
-Modifies session during translation
-Uses Network-specific prefix

NPTv6
-Maps one IPv6 address prefix to another IPv6 prefix
-Modifies IP IP Header in Transit

@Tralala
It is Q567 from networking dump. Was it on an exam?

RECENT TEST TAKERS:

It appears that from recent posts, the 195q dump is not longer valid.
Rather than asking you to recall specific new questions you had seen on your exam, I’d like to ask you the following:
Can you name any topic(s) that did not have much coverage in the 195q dump but now there are a lot of questions about this topic(s)? Were there a lot of new questions about BGP?

Thanks!

ESTION 416
Which action can you take to mitigate unicast flooding in a network?
A. Configure VLANs to span multiple access-layer switches.
B. Implement a nonlooped network topology.
C. Set the ARP timer value to less than the CAM timer value.
D. Set the CAM timer value to less than the ARP timer value.
Correct Answer: C >> This is correct

QUESTION 690
How can you minimize unicast flooding in a network?
A. Configure HSRP on two routers, with one subnet preferred on the first router and a different subnet preferred on the second router.
B. Set the router’s ARP timeout value to be the same as the timeout value for Layer2 forwarding table entries.
C. Set the router’s ARP timeout value to greater than the timeout value for Layer 2 forwarding table entries.
D. Set the router’s ARP timeout value to less than timeout value for Layer 2 forwarding table entries

Correct Answer: B >> should be D

the answer for both is the ARP time is LESS than the CAM time

QUESTION 690–>WHY D?
How can you minimize unicast flooding in a network?
A. Configure HSRP on two routers, with one subnet preferred on the first router and a different subnet preferred on the second router.
B. Set the router’s ARP timeout value to be the same as the timeout value for Layer2 forwarding table entries.
C. Set the router’s ARP timeout value to greater than the timeout value for Layer 2 forwarding table entries.
D. Set the router’s ARP timeout value to less than timeout value for Layer 2 forwarding table entries

Correct Answer: B >>> Should be D
learningnetwork.cisco.com/thread/117389

———————

QUESTION 743–> WHY B?
What is the output of the following command:
show ip vrf
A. Show’s default RD values
B. Displays IP routing table information associated with a VRF
C. Show’s routing protocol information associated with a VRF.
D. Displays the ARP table (static and dynamic entries) in the specified VRF

Correct Answer: A
——————————-

@abdulrahmansh
hi bro

QUESTION 693 –> WHY D?
Company is deploying a multicast applic ation that must be accessible between sites, but must not be accessible outside of the organization
Based on
A. FF00:/16
B. FFOE:/16
C. FF02:/16
D. FF08:/16
Correct Answer: C

__________________________________________________________________________________________________
QUESTION 702
Which two statements about the enable secret and enable password commands are true? (Choose two)
A. I both commands are missing from the global configuration,vtp lines use the console password
B. The enable secret command overrides enable password
C. The enable password command has a stronger encryption algorithm than enable secret
D. The enable secret commmand is bac kwards-compatible with more version of IOS
E. The enable secret and enable password commands must be used togerher
Correct Answer: AB
Section: Networking – Questions-August

QUESTION 547
what are the two correct statements about enable secret and enable password command
A. the enable password command has a strong encryption algorithm than enable secret
B. if both commands are missing from the global configuration, vty lines use the console password
C. the enable secret command is backwards compatible with more versions of IOS
D. the enable secret and enable password commands must be used together
E. the enable secret command overrides enable password
Correct Answer: CE
Section: Networking – NEW Questions

————————————————————————————————-
QUESTION 394
Which two commands must you configure in the calling router to support the PPPoE client? (Choose Two)
A. peer default ip address pool
B. bba-group pppoe
C. pppoe-client dial-pool-number
D. mtu
E. pppoe enable group
Correct Answer: CD
Section: Networking – Questions DAY-4
Explanation

QUESTION 504
Which two commands do you need to implement on a router to support PPPoE client?(Choose Two)
A. peer default ip address pool
B. MTU
C. bba-group pppoe
D. pppoe enable group
E. pppoe-client dialer-pool-number
Correct Answer: BE
Section: Networking – NEW Questions

QUESTION 720
Which two commands do you need to implement on a router to support the pppoe client? (Choose Two)
A. peer default ipaddress pool
B. mtu
C. bba-group pppoe
D. pppoe enable group
E. pppoe-clientdialer-pool-number
Correct Answer: BE
Section: Networking – Questions-August

————————————————————————————————-
QUESTION 379
Which two features does RADIUS combine? (Choose Two)
A. Telnet
B. Accouting
C. SSH
D. Authenticaiton
E. Authorization
Correct Answer: DE
Section: Networking – Questions DAY-4

QUESTION 477
Which two features RADIUS combine? (Choose two)
A. telnet
B. SSH
C. Authentication
D. Authorization
E. Accounting
Correct Answer: CD

QUESTION 658
Whcih two features does RADIUS combine?(Choose two)
A. authorization
B. authentication
C. ssh
D. accounting
E. Telnet
Correct Answer: AB

Does anyone know where I can get the 757 dump? I would really appreciate it. Thanks.

@Kaktus, Elvis87
I started to collect the questions which are in Q757 networking dump. In this moment are 77 questions.
If you give me a contact I will send you.

Router Rider send what you have to vaiking2020 @ Gmail . Com.

@RouterRider francesco dot andreani 87 @ libero dot it

Thank youuu so much!!!

@RouterRider, pls send to angelvelmont @ g m a i l . c o m Thank You!

@RouterRider send me please mss279970 @ Gmail. Com.

Mr.networking replied my mail. He does think that stduying 757q is still enough to pass the exam.
195q is not enough.

I think we need a leader just like nnneettworrkinng to collect the new questions. Elvis87 or Kaktus could you lead the group?

mr RouteRider kindly send update dumo emad4awad yah dot com

Hello guys, which comments page i can find the latest ver of the dumps, thanks in advance

@RouterRider – please kindly send to forzasounds @ gmail. com

@RouteRider – Please kindly send the dumps to Obidullahhakime8 @ gmail. com

@RouteRider please create a link in Cloud like networking, and every one can participate and download the file from it ! The goal here is to contribute and share :) tank you for your efforts friends

@RouterRider – could you please share me the dumps which you prepared to mohammed(.)sameer2k13 @ gmail(.)com.

Thanks in advance.

From dump 757, question # 342:
Which statement is correct regarding the operation of NAT-PT between the IPv4 and IPv6 networks shown?
A. The router will determine the IPv4 destination address.
B. The source IPv6 host can use DNS to determine the IPv6-to-lPv4 address mapping.
C. The host is statically configured with the IPv6-to-lPv4 address mapping.
D. ICMP can be used to determine the IPv6-to-lPv4 address mapping.
Correct Answer: B

Why is B the correct answer?

There is a router named NAT-PT between the IPv6 Host and the IPv4 Host.
If the IPv6 host itself will using DNS to get the IPv4 address then:
(1)
how will the IPv6 host pass the packet to the NAT-PT router in between using the obtained IPV4 address since the network between the IPv6 Host and the NAT-PT router is IPv6.
(2)
If IPv6 itself is obtaining the IPv4 destination address, then what’s the role of the NAT-PT router in between this IPv6 host and IPv4 destination host.

There isn’t new dump! I collected the exam questions which was written in this week here and searched from networking dump.

Guys.. im doing the gns3 PBR lab, but my when i generate icmp traffic my route-map doesnt get matches?? did anyone have same issue?

@Zamtaker Which Alc did you use?

Access-list 101 permit icmp any any echo should be ok

Nvm guys, i changed the acl to match www and do telnet on port 80, then it works. weird

@Elvis87
Aah stupid me, i wrote permit tcp any any echo instead of icmp loool omg

I heard that pass4sure is up to date, I hope that an angel chared it here ! I am now searching in the China forum to collect the new questions to share in this forum :)

1) Choose 2 methods for migrating routing protocols
Answers: Changing AD distance and Redistributing

2) QUESTION about Choose best IP SLA deployment cycle that reduce deployment.
Answer: Baseline Network Performance, Undertanding Network Performance Baseline, Quantify Results, Fine Tune and Optimize.

3)One new question with choose correct statement about nat. You will see configuration of nat with nat pool (Dynamic Nat)
Answers: There were list config for private add. 2 similar options for this list. Correct answer has to be with a word “inside local”. Second correct options you will
Something “this list will be translated to this subnet (which is pool)”. DO not choose it translates one-to-one

4) What Snmp v2c use for authentication
Answer: community string

5) One long queadstion about router get ipv6 infos from ISP. Now it have to distribute name server and other options to hosts (LAN).
Choices

6) one new DND about DMVPN, meaning of HUB, SPOKE, mGRE, NHRP.

7) One DND Frame relay LMI extensions.

8) one question about ipv6 eigrp features supported (choose 2)
Answer: scaling and partial updates.

9) QUESTION about PADO, PADI, PADR Answers: PADR(PPPoE Active Discovery Request) and PADI (PPPoE Active Discovery Initiation)

LABs: EIGRP Stub, OSPF and EIGRP redistribution, PBR all labs from DigitalTut.

10) New question about SNMP
Which security level is supported throughout all snmp versions?
-authPriv
-authNoPriv
-noAuthNoPriv
Answer: noAuthNoPriv

could you tell me if there was any evaluation sim apart from labs ?

also, did you get only these below 5 DnD’s

1)LMI extension
2)Router, TxACACS SERVR,USER
3)Frame Relay Components
4)DMVPN
5)IP SLA cycle deployment

Hi everyone,

I just joined this forum hoping to write my exam by the end of the month or first week of Dec. Thank you to Mr David for taking the initiative to send Neworkinggggggggg an email. Kindly ask him to please update on the new questions once they are available to him.
Thank you Mr networkingggggggg, you are simply the best.

@Milliniume
are u sure about pass4sure ?? Someone told me it doesnt even have drag and drop questions

Can u send me DUMPS please :
mmeedd0509((@))gmail.com
please remove “(( and ))”

@Milliniume
on the bottom of pass4sure com it says:
© All Rights Reserved 2005-2018 Pass4sure.com. Pass4sure.com Materials do not contain actual questions and answers from Cisco’s Certification Exams.

Guarantee Policy is not applicable to Cisco, Admission Tests, Language Courses, Avaya, CISSP, EMC, HP, Oracle, PMI and SSCP exams as http://www.pass4sure.com provides only the practice questions for these.

Please share if you have 195Q dumps. I don’t know where to buy.
the tech snafu @ gmail . com