Share your ROUTE v2.0 Experience

I passed the route exam with 9xx.
The networkeeening dump is valid (100%)…all multiple choice and dnd were from networkeeening
the Sim were redistribution, ospf sim, eigrp stub sim.

I am very grateful for digitaltut and networkeeening!!!
Good luck to u all.

i passed today with 900 mark, 195q are still valid.

however i still have some concerns on the ospf-redistribution lab( setting admin-distance from redistributed ospf routers on eigrp on R3 and R2. becouse the routes are not getting the configured distances on external routes ( on eigrp) at R1.

Hello all,, what is the correct answer
Refer in the exhibit. A packet capture indicates that the router is not forwarding the DHCP packets that it receives on interface FastEthernet0/0. Which command needs to be entered in global configuration mode to resolve this issue?
A. ip helper-address
B. ip DHCP relay
C. service DHCP
D. ip forward-protocol

Hello all,, what is the correct answer
Refer in the exhibit. A packet capture indicates that the router is not forwarding the DHCP packets that it receives on interface FastEthernet0/0. Which command needs to be entered in global configuration mode to resolve this issue?
A. ip helper-address
B. ip DHCP relay
C. service DHCP
D. ip forward-protocol

NEW QUESTION 688
Which three algorithms can you configure with the ip cef load-sharing algorithm command? (Choose three.)

A. per-packed
B. Tunnel
C. per-destination
D. Universal
E. Per-source
F. Include-ports

Answer: BDF

NEW QUESTION 689
Which tecnology supports overlapping IP address on a single interace?

A. policy-based routing
B. VRF-Lite
C. On-Demand Routing
D. QoS

Answer: B

@CCNP- its ip forward-protocol

Exactly Kcha, I also think there’s something wrong with that lab, cant get any routes on R1 with GNS3 lab. something is missing

@Ricardo Morales

can you share the material you used for the exam?

Thank you Sofie

Awesome VCE simulator

Lantosy

STop Fake link advertise please block Lantosy link

Money hunger dont waste time.

NEW QUESTION 682
Which security feature can protect DMVPN tunnels?

A. IPsec
B. TACACS+
C. RTBH
D. RADIUS

Answer: A

NEW QUESTION 683
What happens when two EIGRP peers have mismatched K values?

A. The two devices are unable to correctly perform equal-cost routing.
B. The two devices fail to perform EIGRP graceful shutdown when one device goes down.
C. The two devices fail to from an adjacency.
D. The two devices are unable to correctly perform unequal-cast load balancing.

Answer: C

NEW QUESTION 684
Which two features were added in MSCHAP version 2? (Choose two.)

A. Mutual authentication between peers.
B. Using the MD5 hash foxaxr stronger security.
C. Using three-way handshakes for authentication.
D. Ability to change an expired password.
E. Backward-compatibility with MSCHAP version 1.

Answer: AD

NEW QUESTION 685
When an EIGRP router discovers a new neighbor, which packet type does the router send to help the neighbor build its topology table?

A. Replies
B. Requests
C. Updates
D. Queries

Answer: C

Passed today with 966. Thanks to networrkkkk
100% valid 195q

I passed my ccnp route today. The 195q vce and the labs given are 100℅ valid. Got a 900+ score.

Can follow them

are digital tut labs valid!?

Passed today everything on networrkkkk 195 still valid labs eigrp stub, ospf virtual link, eigrp ospf redistribution. DND AAA, IPV6, and GRE.. on to TS.

@Anonymous
What type of route filtering is occuring on R6?
A. Distribute-list using an ACL
B. Distribute-list using a prefix-list
C. Distribute-list using a route-map
D. An ACL using a distance of 255

pretty sure you can use both, in fact one of these sims uses an ACL with a dist-list AND i have recreated every one of these labs in GNS3 so i know for a fact you can reference an ACL in a dist-list. Route map also, look it up.

https:// http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_eigrp/configuration/xe-3s/ire-xe-3s-book/eigrp-route-map.html#task_971EB39757994D87AD6082B59DF1B072

I passed the test like an hour ago.

The 195q dump is 1000 x 10000 valid, dont pay for dumps the below link contains what you need to pass the exam for free.

Thanks 9tut and thanks neeetworkiiiing.

https:// drive.google. com/drive/folders/ 1Cf4MHTm8Qt5-_jYzJt6PXNy6b6YOBEx1

can you send Pass Leader 300-101 dumps with 739q version please?

Any update on the exam today?

hello all, what is the correct answer
When OSPF is forming an adjacency, in which state does the actual exchange of the information in the link-state databse occur?
A. INIT
B. Exstart
C. Loading
D. Exchange
B or C

@CCNP, I Think it’s loading. Exstart is where the DR/BDR election happens

@Mosh thanks bro..

Hello All

I passed the exam this week using Madison dumps posted above

https://mega.nz/#!GjI32YAa!jV-ycGC0kizwk36L3ut1WPzjW2Tmuyqoltnt1fc-g2w

You can reply on them to pass the exam

Good luck to everyone

Best Regards,

I passed today! (195Q still valid – answer is D) but correct answer is A

Actions can be to syslog, limit or shutdown VLAN
https://www.cisco.com/c/en/us/support/docs/switches/catalyst-6000-series-switches/23563-143.html

What happends when unicast flood protection is triggered on a VLAN?

A. The VLAN is shut down
B. Traffic on the VLAN is load-balanced across multiple links
C. The VLAN is removed from the VLAN database
D. Traffic on the VLAN is passed to another VLAN with lower load

@CCNP route
which question you get exam DD / Lab ?
Thank u

hi can i have the latest ccnp 300-101 dumps. please email me to fyazzayf(at)gmail(dot)com

many thanks brothers!!

@CCNP Route, what country did you take the exam?

hello all in this question in 195q
QUESTION 709
which access list used to filter upper layer protocol ?
A. extended acl
B. standart acl
C. reflexive acl
D. time based acl
E. dynamic acl
correct answer is C not A according to this:

https://www.cisco.com/en/US/docs/ios-xml/ios/sec_data_acl/configuration/15-1s/sec-access-list-ov.html

Reflexive Access Lists
Reflexive access lists provide filtering on upper-layer IP protocol sessions. They contain temporary entries that are automatically created when a new IP session begins. They are nested within extended, named IP access lists that are applied to an interface. Reflexive access lists are typically configured on border routers, which pass traffic between an internal and external network. These are often firewall routers. Reflexive access lists do not end with an implicit deny statement because they are nested within an access list and the subsequent statements need to be examined.

hi bros!! please please help me. kindly send me the latest dumps to my email. fyazzayf at gmail dot com

i have my exam in 2 days!! please help someone.

THanks!!

Please some help here!
ON OSPF SIM they ask specifically to configure:
Portland’s S0/0 interface in Area 1 and Amani’s S0/1 interface in Area 1, why they are not doing it in the resolution?

shouldn’t we add them in the exam?

Portland:
#int se0/0
#ip ospf 1 area 1

Amani:
#int se0/1
#ip ospf 1 area 1

DO WE HAVE TO DO THIS ON THE EXAM!!!???

Passed 20 mins ago
question were all 195 Q
Labs…..Redistributio, Ospf conf and Eigrp Stub.

congratiolation Said

whre i kan find the 195 Q please

Does anyone have the route videos i can download via FTP, thanks in advance.

Guys there are new questions posted here, does anyone trying to update networkinggggg dump??

Hi All

How is going

My dums still valid
you should reading all Questions but Focus just 195 Questions
good luck Guys

https: // drive.google.com/drive/folders/1Cf4MHTm8Qt5-_jYzJt6PXNy6b6YOBEx1?ogsrc=32

@ thanks bro,,
my exam is tomorrow, do i have to read all the question?
or just 195q is enough?

@nneettwwrrookkiinnggg

@MAI
Q1 C
Q2 A, E

@@@
C

Passed today 8xx
Labs EIGRP stub, Ospf virtual links, OSPF EIGRP redistribution
DD copp&MPP , tunnel key tacacs raduis accounting ,
new questsion
what’s two reason of latency
1-serialization delay
2-propagation delay
3-under utilization of link
4—
New question 2
complete frame relay multpoint configuration
All questions from here and vceplus online questions

These are the questions which are repeated several times & everytime they have different answers, if you can help, it would be much appreciated. I did my own research so i’ll choose those answer in my exam but lets double check ahaha.

Which two causes of latency are true? (Choose two)
A. High bandwidth on a link
B. Split horizon
C. Propagation delay
D. Serialization delay
E. Under-utilizaion of a link

Which two statements about the enable secret and enable password commands are true? (Choose two)
A. I both commands are missing from the global configuration,vtp lines use the console password
B. The enable secret command overrides enable password
C. The enable password command has a stronger encryption algorithm than enable secret
D. The enable secret commmand is bac kwards-compatible with more version of IOS
E. The enable secret and enable password commands must be used togerher

How big is the smallest packet than will always be fragmented on a standart Ethernet network with default configuration?
A. 1500 bytes
B. 1800 bytes
C. 2048 bytes
D. 2100 bytes

Which two statements are true about EVN? (Choose Two)
A. A configuration can be based on an existing VRF configuration
B. It supports IPv6 traffic
C. It can support up to 16 VNs
D. It uses redistribution to share routers between VNs
E. It supports SSM only

In which state do DR and BDR establish adjacency with each ospf router in the network

A. Exstart State
B. Loading State
C. Exchange State
D. Init State

Which criterion does the BGP maximum path feature use for load balancing?.

A. Router ID
B. MED
C. Weight
D. Local Pref

which protocol use both best path and second best path for traffic??
A. EIGRP
B.OSPF
C.BGP
D.RIP

If this configuration is applied to a device that redistributes EIGRP routes into OSPF. which two statements about the behavior of the device are true? (Choose Two )
A. EIGRP routes appears in the routing table as E2 OSPF routes
B. The device router ID is set to Loopback0 automatically
C. The device redistributes all EIGRP networks into OSPF
D. EIGRP routes appears in the routing table as N2 OSPF routes
E. The device redistributes only classful EIGRP networks into OSPF
F. EIGRP routes appears as type 3 LSAs in the OSPF database

What happends when unicast flood protection is triggered on a VLAN?
A. The VLAN is shut down
B. Traffic on the VLAN is load-balanced across multiple links
C. The VLAN is removed from the VLAN database
D. Traffic on the VLAN is passed to another VLAN with lower load

In which two areas does OSPF send a summary route by default ?
A. NSSA
B. Backbone
C. Totally stubby
D. Stub
E. Normal

Hi – please share latest dumps for Route exam thank you

Hi! Ill be taking route exam this November. Do I just need to study 195q from nneettwwoorrkkiinngg? How about the laba? Thanks for who will answer me.

Hey guys,

I passed the exam today, scored 9xx, 195Q is still valid. Thank you all for being part of this great community in special to nneettwwoorrkkiinngg and the other folks that keep clarifying doubts.

D&D: ACL Types, GRE, uRPF
Labs: OSPF, EIGRP OSPF Redistribution, EIGRP Stub

@maraton, Thanks! What country did you take the exam?

Hey guys,

I passed the exam today, scored 9xx, Thank you all

D&D: ACL Types, GRE, uRPF
Labs: OSPF, EIGRP OSPF Redistribution, EIGRP Stub

https:

Faaaaaaaaake!!!!

hello all,
passed the exam one hour ago
all questions from 195q (195q is super valid)
@nneettwwrrookkiinnggg thanks bro

@goggleplexx Some questions that have different answers
Some of the questions you have to prove each answer choice FALSE and then what is left over is the “CISCO Truth” lol
Here is how I will answer them with reference :

Which two causes of latency are true? (Choose two)
A. High bandwidth on a link
B. Split horizon
C. Propagation delay
D. Serialization delay
E. Under-utilizaion of a link
ANSWER: C D
Yes “A” could be a choice, but “A” may cause other issues and the subject is latency. So in a normal operating network, engineered, under normal conditions latency would be caused by the factors of propagation and serialization.
Propagation is how long it takes packets to get to A and B , serialization is the delay from putting a byte in a buffer and pulling one out.

Which two statements about the enable secret and enable password commands are true? (Choose two)
A. I both commands are missing from the global configuration,vtp lines use the console password
B. The enable secret command overrides enable password
C. The enable password command has a stronger encryption algorithm than enable secret
D. The enable secret commmand is bac kwards-compatible with more version of IOS
E. The enable secret and enable password commands must be used togerher

ANSWER A B
C Not true (Just read any cisco stuff on enable secret and enable password)
D Enable secret was released after enable so Not true
E Not true (Just read any cisco stuff on enable secret and enable password)

How big is the smallest packet than will always be fragmented on a standart Ethernet network with default configuration?
A. 1500 bytes
B. 1800 bytes
C. 2048 bytes
D. 2100 bytes

ANSWER B
Key is the word “smallest packet” out of A B C or D Since A (1500) wont be fragmented in a default network the next lowest is 1800.

Which two statements are true about EVN? (Choose Two)
A. A configuration can be based on an existing VRF configuration
B. It supports IPv6 traffic
C. It can support up to 16 VNs
D. It uses redistribution to share routers between VNs
E. It supports SSM only
ANSWER B C
A ? FALSE
B true
C true
D ? FALSE
E FALSE
https://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/layer-3-vpns-l3vpn/whitepaper_c11-638769.html

In which state do DR and BDR establish adjacency with each ospf router in the network
A. Exstart State
B. Loading State
C. Exchange State
D. Init State
ANSWER B
https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/13685-13.pdf

Which criterion does the BGP maximum path feature use for load balancing?.
A. Router ID
B. MED
C. Weight
D. Local Pref

ANSWER C
Weght is the first feature to consider MED and Local Pref are further down the list.
This explains https://learningnetwork.cisco.com/thread/42531

which protocol use both best path and second best path for traffic??
A. EIGRP
B.OSPF
C.BGP
D.RIP
ANSWER A
B and C do not have load balancing
By default BGP does not load balance.
EIGRP is->load balancing…
https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/5212-46.html

If this configuration is applied to a device that redistributes EIGRP routes into OSPF. which two statements about the behavior of the device are true? (Choose Two )
A. EIGRP routes appears in the routing table as E2 OSPF routes
B. The device router ID is set to Loopback0 automatically
C. The device redistributes all EIGRP networks into OSPF
D. EIGRP routes appears in the routing table as N2 OSPF routes
E. The device redistributes only classful EIGRP networks into OSPF
F. EIGRP routes appears as type 3 LSAs in the OSPF database
Sorry i cant see configuration to answer this

What happends when unicast flood protection is triggered on a VLAN?
A. The VLAN is shut down
B. Traffic on the VLAN is load-balanced across multiple links
C. The VLAN is removed from the VLAN database
D. Traffic on the VLAN is passed to another VLAN with lower load

ANSWER A
https://www.cisco.com/c/en/us/support/docs/switches/catalyst-6000-series-switches/23563-143.html

In which two areas does OSPF send a summary route by default ?
A. NSSA
B. Backbone
C. Totally stubby
D. Stub
E. Normal
ANSWER B E
(NSSA TOTALLY STUBBY and STUB by default do not have summary)
http://www.ciscopress.com/articles/article.asp?p=2294214&seqNum=3