Share your ROUTE v2.0 Experience

@Dupre, i appreciate the info for 300-135 exam, but we re dealing with some topics and doubt for the 300-301 exam so far, if you can kindly add some feedback of the @Mac or some of my questions will be a great help.

Refer to the exhibit. The network setup is running the RIP routing protocol. Which two events will occur following link failure between R2 and R3? (Choose two)
RIP_Unreachable.jpgA. R2 will advertise network 192.168.2.0/27 with a hop count of 16 to R1.
B. R2 will not send any advertisements and will remove route 192.168.2.0/27 from its routing table.
C. R1 will reply to R2 with the advertisement for network 192.168.2.0/27 with a hop count of 16.
D. After communication fails and after the hold-down timer expires, R1 will remove the 192.168.2.0/27 route from its routing table.
E. R3 will not accept any further updates from R2, due to the split-horizon loop prevention mechanism.

What the correct answer?

@lunchi

1. R2 will advertise network 192.168.2.0/27 with a hop count of 16 to R1.
2. R1 will reply to R2 with the advertisement for network 192.168.2.0/27 with a hop count of 16.

Can anyone send me the latest dump to stepheney12321 @ gmail .com

Thank you in advance!

@Anton

I agree with you, please, check this link out:

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/evn/configuration/xe-3s/evn-xe-3s-book/evn-overview.html

can any one send latest dumps on suffianmanzoor @gmail.com

Thanks in advance.

Thank you Sajad bhai for sent me dumps.

Actually I need latest updates of procyber or any other updated dumps.
If any one confirm about changes in dumps or any updates, please inform us and if any body have those please share with us.

PASSED!

Procyber questions are still valid, LABs were almost the same 1-2 thing was different.

The VPN part scoring was quite low so there can be wrong answers in the dump!

Hi Guys,

Doubts about this Qs:

IP CEF load-sharing options (choose three)

A. Tunnel
B. Universal
C. Include-ports
D. Source
E. Destination

Dump says: A, B, C. But investigating, I think the correct Ans is A, C and E.

Please help!!

Thanks

Hey Guys,
I really appreciate if you could send me/ share a link for the latest reliable dump.
mo dot sajjadi at g m a i l dot com

8XX/1000
Now next target is CCNP Switch
TKX digitaltut

@IVOIRYCOST
Did you have any new questions?

@mhr
no new questions.
all questions are hear.
procyber dumps valid
pay attention on lab

@IVOIRYCOST
Congrats and thank you for sharing information!

@IVOIRYCOST
which labs do you have in the exam and is there any changes in them

@and1lan10
the answers ABC are correct. see the syntax on the cisco website:

ip cef load-sharing algorithm {original | tunnel [id] | universal [id] | include-ports {source[id]| [destination] [id] | source[id] destination [id]}}

your have three options: tunnel, universal and include ports.
destination and source are only options under the option include ports.

Can someone send latest dump which is procyber 1.5 as I am planning to give exam next week.
tarun.chintu at gmail dot com

Thanks in advance

Pass today 8xx
Labs equal here, DND equal but answers are not ordenaded like here and procyber 1.5
5 new questions some of them question is the same like dumo bur responses are different remember one of them that response is abr and abrs but in exam appears like internal router external etc…
Procyber 1.5 still valid.

Not easy exam with the most dificult questions that i have in dump.
Vpn only have 33% score…

Thanks to all and digitaltut…
Without study you dont pass
Dumps are not enough.
Good luck for all

@ all

Hi guys, im going to take the exam next month.
i have procyber 1.5 vce and i would like to know if the i need to know all the questions or just the latest 200 or something like that..
thx

@FifaPlayer
You need to know all of them ) And a little more. The labs are still important.

@mhr

thx for the answ

the labs are not a problem cause i work everyday with routers, just a bit scared about more or less 500 questions … at the exam are just 40.. in the others dumps (switch or ccna) were just 200..

Note: labs are equal, the troubleshoting, ips and areas etc are diferent

@fifaplayer
50% of exam answers are disorded… so pay atention when you studie in dumps… you must understant the answers if not you fail….
I have almost 50 question in my exam…

Does anyone have any info for the correct asnwer in here.??

Question 7
In which scenario can asymmetric routing occur?
A. active/active firewall setup
B. single path in and out of the network.
C. active/standby firewall setup
D. redundant routers running VRRP
Answer: D (?) or A (?) or (?)

to my understanding A is the correct answer

@FifaPlayer
It’s not so many questions in dumps. Some of them are almost identical, some of them are very similar. Good luck anyway!

@Help!!!
From my point of view – A. But the Johny Bravo gave us pretty interesting explanation at this page. So now I’m simply not sure…

hi guys, does anyone have the link where it shows the percentage on cisco.com for the topic of the exams?

i got it:

https://learningnetwork.cisco.com/community/certifications/ccnp/route_v2/exam-topics

hi team,

can anyone tell me which is the most difficult lab and why?

Passed CCNP Route Today with 9xx. All question were from this site and the Procyber V1.5. I had prepared using CISCO CCNP official Certification guide (Kevin Wallace) , before referring to this site. That helped me a lot with the concept. But I wouldn’t have cleared the Exam without the help of you guys!. Thank you so much!. Keep up the good work

Labs : Redistibution, PBR, OSP, EIGRP Eval, OSP Eval. IP’s and Area ID’s were changed. But concept remained the same.
DnD’s are all from this site and Procyber

But I believe some of the answers in the Vce and this site are wrong . (Otherwise I would have scored Full :) ).

@Thank you DigitalTuT

i heard there are only 4 labs, but you mentioned 5, did you really did 5 or 4?

regards,

@help!!! the answer is A as per the below:

In firewalls, state information is built when the packets flow from a higher security domain to a lower security domain. The firewall will be an exit point from one security domain to the other. If the return path passes through another firewall, the packet will not be allowed to traverse the firewall from the lower to higher security domain because the firewall in the return path will not have any state information. The state information exists in the first firewall.

484 is vaild ?

saifty81(at)gmail(dot)com

300-101 valid dumps

saifty81(at)gmail(dot)com
300-101 valid dumps

saifty81(at)gmail(dot)com
1
2
3
300-101 valid dumps

Failed today with 7xx.

One of the things that got me was the OSPF Lab. It wasn’t like the one on here because one of the requirements was that all routers had a Priority ID of 74. One the first router I tried the command “Router OSPF 74” but it said something like “Can’t use because it’s not setup on another IP” …on the 2nd router I tried “Router OSPF 74” again and it worked so I used it for all my commands. Then I went back to the first router and again still no go on it so I ended up using “Router OSPF 1” which i knew wasn’t right but was hoping to get some of the points for the exam to pass…

I barely missed pass. The other SIMS / LABS were the same although some of the show commands are disabled. Like “sh ip ospf database” was disabled a lot when I went to use it in the evaluation sections. I would had passed had I got the OSPF right though. Can anyone help me out to what to do if I get that “OSPF Priority ID 74” again? I want to retake next week.

I also got PBR / Redistribution but I did fine on those and the eval ones.

@Johnny What was the required outcome in the exam for the sim ?

Was the network setup similar to the one on here ?

https://www.digitaltut.com/final_flash/IPv6_OSPF_virtual_link_sim/IPv6_OSPF_virtual_link_sim.html

@Arsi No it was this one:

https://www.digitaltut.com/final_flash/OSPF_Sim/OSPF_sim.html

But it was different requirements/different router names with the same concept. They wanted all routers to have priority ID 74…when i tried to put “Router OSPF 74” on router “Portland” (It wasn’t named Portland in exam), it said something like “Can’t use because it’s not setup on another IP” etc… so i then used “Router OSPF 74” on the 2nd router (middle router) and it worked. But I could not get “Portland” router (the far left router) to have priority ID 74…hoping for some guidance. Thanks

I ended up using “Router OSPF 1” on “Portland” router which I knew wasn’t right but was just trying to save a few points on exam versus just leaving it blank so I used Priority ID 1 on that router and finished my commands w the wrong ID. Again I knew that was wrong but when testing just trying to save myself a few points vs leaving it blank.

i am not understanding why some people show saying that there are 4 labs only, when i see others saying that there are 5 in the exam.

@Johnny, which OSPF sim lab did you do, the one that has (3 routers named portland, Amani and Lynanic? if that so, where did you see that we need to configure an ID of 74?

i have not seen that on this lab!

@byakura yes the one with portland, Amani, and Lynanic. I hadn’t seen it either so no way to prepare for it and I missed it. If you look in the comments on that lab page though you wil see someone else mentioned the Priority ID 74 came up in their lab too….I need to know the solution if I get it again because I want to retake next week ..help please

@Johnny, yes i am working on it, cuz i am doing the exam this week and i have not practiced that lab at all, i though they were only four.

so basically you did 5 at the end, (EGRP EVA, OSPF EVA, PRB, and OSPF and EIGRP redistribution along the OSPF SIM am i right? andn you had no problem with others?

as soon as i get good information regarding this lab, i will let you know, after all it seems not to be so hard at all
################################################

Portland#configure terminal
Portland(config)#router ospf 1

Allow network 192.168.4.4/30 to join Area 1, notice that you have to convert subnet mask into wildcard mask:

Portland(config-router)#network 192.168.4.4 0.0.0.3 area 1
Configure Portland as a stub:
Portland(config-router)#area 1 stub
Portland(config-router)#end
Portland#copy running-config startup-config

+ Configure Amani router as a “totally stub”:

Amani#configure terminal
Amani(config)#router ospf 1
Amani(config-router)#network 192.168.4.4 0.0.0.3 area 1

Make area 1 become a totally stubby area, notice that we can only use this command on ABR router:

Amani(config-router)#area 1 stub no-summary
Amani(config-router)#end
Amani#copy running-config startup-config

i am assuming that they are changing router names and other things.

as you know i pasted the resolution, so we can start by changing the possible new things you faced or someone who did it may help us in knowing what else needs to be changed on the above lab.

@Johnny
The OSPF priority can be set by the following command

ip ospf priority number-value

https://www.cisco.com/c/m/en_us/techdoc/dc/reference/cli/nxos/commands/ospf/ip-ospf-priority.html

@byakura

I had 5 labs. But 2 of them were Evals (EIGRP and OSPF). I did not have to configure anything for the Evals, Just answer questions based on the show commands. Same EVAL SIM’s as in this site.

For OSPF , requirement was all Routers should be in OSPF 34 and the link which I had to configure should be in Area 25. Router names were different too, Like Seattle, Chicago and Atlanta. and had to ping Atlanta Loopback at the end.

PBR and Redistribution was exactly the same (IP’s might have been different).

Saving to Startup config worked on some labs. Didnt work on others.

@Johny
Are you sure it was OSPF Priority Id? My Lab had OSPF Process Id to be 34 in all routers as a requirement.

Johnny
I think you must don’t delete ospf 1 till create ospf 74 and add network command under 74

@byakura Yes, exactly. I did EIGRP/OSP Evals (some of the sh commands were disabled but I was able to find my answers in show running-config where needed). PBR and OSPF/EIGRP redistribution were both on there and I cleared that based on everything on here. But the OSPF Sim was changed requiring that the routers use Priority ID 74. When I tried “Router OSPF 74” on “Portland” it said something along the lines of “Can’t use because it’s not setup on another IP” )if I recall correctly. I then tried “Router OSPF 74” on 2nd router and it worked sop I finished my commands on that router. I went back to Portland and tried re-issuing “Router OSPF 74” and got the same message so I gave up and went with “Router OSPF 1” and finished my commands which I knew was wrong but didn’t want to leave it blank. I need help solving this issue should I see it again next week please

@thank you I think you’re right. How did you resolve that lab exactly?