Share your ROUTE v2.0 Experience

@network en

CD

OSPF will trigger updates if there is a change; it will also refresh LSA’s every 30 minutes if there have been no changes.

http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_ospf/configuration/xe-16/iro-xe-16-book/iro-cfg.html

Also, 224.0.0.6 is all OSPF DR’s. 224.0.0.5 is all OSPF routers.

@hp-667y

The ipv4 virtual-link lab is exactly the same topology as ipv6 virtual-link lab – different router names and only ipv4 ip addresses. One area is not connected to area 0 so virtual-links are required to provide connectivity

The hardest part is the last bit where they ask you to ensure the the router you just applied the virtual-link on is not receiving any inter-area or external routes

On to CCNP-SWITCH :)

how did you solve that? You cant use a stub area on a virtual link.

did you configure a route map?

@Destroyer

are you sure that it was new or is it this lab:

digitaltut.com/route-ospf-sim

sonu my friend please can you support me neeetttworrrking dumps 195 in this email muhsinmuumin at gmail dot com

if anyone took the exam? if 195qs networking still valid??

Hi friends

Do we still get OSPF and EIGRP Evaluation simlets in the exam or only the LABS, i have exam on 27Sept. Those who passed recently your valuable inputs will be really needed and any last minute exam tips plz. thanks in adv.

@Destroyer
you can give us more details of the new laboratory (commands and that is exactly what they are asking to configure)

@Destroyer
you can give us more details of the new laboratory (commands and that is exactly what they are asking to configure)

Which two causes of latency are true? (Choose two)
A. High bandwidth on a link
B. Split horizon
C. Propagation delay
D. Serialization delay
E. Under-utilizaion of a link
Correct Answer: CE ?? can anyone confirm please .

W ww.cci
edumps.xyz?utm_source=bbs&utm_medium=bbs

I just passed the CCIE exam last week. I bought the topic here. The topic is true and effective. I have practiced most of the exam questions, but you have to remember the answer. You can’t just remember it. The options, I have encountered several questions in it, the options for the correct answer have been changed.

Any news on the new lab?

@Sancho & LJ

I dont know what i did was correct but you will have 3 routers on different areas. Like Sancho said you cannot configure STUB with virtual-links on the transit area but you can configure stub command for the non-transit area for example from left to right if areas were:

Area 30 (R3) – Area 11 (R2) – Area 0 (R1)

Then you configure the virtual-links on Area 11 and configure the stub no-summary ( inter-area & external area excluded ) on R3 AREA 30 – the non-transit area

They also ask you to ensure that you have configured ospf process id as 20 ( this value might change ) on all routers and confirm ping connectivity after configuring the /30 links using 0.0.0.3 mask ( ip addresses may change )

Like i said i am not sure if this is correct so someone will have to verify but the above is what i did and it looked like it worked.

Which two causes of latency are true? (Choose two)
A. High bandwidth on a link
B. Split horizon
C. Propagation delay
D. Serialization delay
E. Under-utilizaion of a link
Anwer is CD

please
which protocol use both best path and second best path for traffic??
A. EIGRP
B. OSPF
C. BGb
different answers in different dump

which protocol use both best path and second best path for traffic??
A. EIGRP
B. OSPF
C. BGP
Correct Answer C

Which two causes of latency are true? (Choose two)
A. High bandwidth on a link
B. Split horizon
C. Propagation delay
D. Serialization delay
E. Under-utilizaion of a link

Answer should be A and C

Because the there is high bandwidth on a link it always causes slowness/latency/Packet loss. See that on daily basis. Never seen under utilized link cause latency but Cisco is always tricky they might have different explanation.

hi guys,

the bellow question have different answers in the two dump 192q and networkiiiiiiing dump

1.Which SNMP verification command shows the encryption and authentication protocols that are used in SNMPv3?

A. show snmp view
B. show snmp
C. show snmp user
D. show snmp group

answer b or c

2.Company is deploying a multicast applic ation that must be accessible between sites, but must not be accessible outside of the organization
Based on

A. FF00:/16
B. FFOE:/16
C. FF02:/16
D. FF08:/16

answer C or D

3.A network engineer is enabling RIPng on a new customer link Under which configuration mode is RIPng enabled?

A. Global
B. Router
C. Interface
D. IPv6

answer A or C

4.Which adverse circumstance can the TTL feature prevent

A. routing loops
B. DoS attacks
C. link saturation
D. CAM table overload

answer A or B

5.A network engineer executes the show ip cache flow command. Wich two types of information are displayed in the report that is generated? (Choose Two)

A. top talkers
B. flow export statistics
C. flow sample for specific protocols
D. MLS flow traffic
E. IP packet distribution

answer BC or CE

6.In which two areas does OSPF send a summary route by default ?

A. NSSA
B. Backbone
C. Totally stubby
D. Stub
E. Normal

answer CD or DE

7.How big is the smallest packet than will always be fragmented on a standart Ethernet network with default configuration?

A. 1500 bytes
B. 1800 bytes
C. 2048 bytes
D. 2100 bytes

answer A or B

8.Which task must you perform to enable a point-to-point Frame Relay connection ?

A. Configure the encapsulation type
B. Disable inverse ARP
C. Enable inverse ARP
D. Configure static address mapping

answer A or D

i will pass the exam in the next week
please help for this answers
thanks

Please can someone send me the latest CCNP ROUTE DUMPS on {email not allowed}. I write next month.

route dump
https :// drive.google.com/drive/folders/1mNECPPdUANPrx9u0QOIheDgSQFQL-stY

For @Destroyer’s OSPF Sim:

If we don’t want the router to receive external routes, we have to stop LSA Type 5. And if we don’t want to receive inter-area routes, we have to stop LSA Type 3 and Type 4. Therefore we have to configure area 1 as a totally stubby area. (Stub no-summary)

Destroyers never seens im sounds like that sim:

https://www.digitaltut.com/route-ospf-sim

hi guys,
please show
the bellow question have different answers in the two dump 192q and networkiiiiiiing dump

1.Which SNMP verification command shows the encryption and authentication protocols that are used in SNMPv3?

A. show snmp view
B. show snmp
C. show snmp user
D. show snmp group

answer b or c

2.Company is deploying a multicast applic ation that must be accessible between sites, but must not be accessible outside of the organization
Based on

A. FF00:/16
B. FFOE:/16
C. FF02:/16
D. FF08:/16

answer C or D

3.A network engineer is enabling RIPng on a new customer link Under which configuration mode is RIPng enabled?

A. Global
B. Router
C. Interface
D. IPv6

answer A or C

4.Which adverse circumstance can the TTL feature prevent

A. routing loops
B. DoS attacks
C. link saturation
D. CAM table overload

answer A or B

5.A network engineer executes the show ip cache flow command. Wich two types of information are displayed in the report that is generated? (Choose Two)

A. top talkers
B. flow export statistics
C. flow sample for specific protocols
D. MLS flow traffic
E. IP packet distribution

answer BC or CE

6.In which two areas does OSPF send a summary route by default ?

A. NSSA
B. Backbone
C. Totally stubby
D. Stub
E. Normal

answer CD or DE

7.How big is the smallest packet than will always be fragmented on a standart Ethernet network with default configuration?

A. 1500 bytes
B. 1800 bytes
C. 2048 bytes
D. 2100 bytes

answer A or B

8.Which task must you perform to enable a point-to-point Frame Relay connection ?

A. Configure the encapsulation type
B. Disable inverse ARP
C. Enable inverse ARP
D. Configure static address mapping

answer A or D

i will write the exam in the next week

thanks

@network en
1. type command in google image and see result

2. D, ff08::/16 ff08::/16 well known organization local

3 “new customer link” – I believe ripng is already enabled on router.

4. IMO route course = routing loop

5. type commands in google image

6. explained above

7. “smallest packet than will always be fragmented ” – smallest but will be fragmented. Check how big is ethernet frame.

8. Try to lab …

Just passed now with 966

All questions came from 195q and 3 labs from here.

Thanks

@ worried

which labs came from here?

Hi Fellas,

I just passed the 300-101 exam 922/1000.

nneettwwoorrkkiinngg dumps are valid.

Labs:
– EIGRP Stub SIM
– IPv6 OSPF Virtual Link SIM
– EIGRP OSPF Redistribution Sim
– OSPF SIM – virtual Link configuration.

Good luck

@ greg

thanks for your reply

@network en
1 – c – 100%
2 – d – 100%
3 – c – 50% (as it says on a LINK) you can enable it with “R1(config)#ipv6 router rip RIPNGTEST” or also without the previous “on the interface/link?) with “R1(config-if)#ipv6 rip RIPNGTEST enable”
4 – a – (99%)
5 – CE – (99%)
6 – A&D – When you see a “totally” means no summary. Types three (summary) LSA will be from an ABR. so you have stub and not-so-stubby-area
7 – B (300 header + 1500)
8 – A (need to set the encapsulation type with R1(config-if)#encapsulation frame-relay)

I have my exam Friday, could anyone please tell me:

I see everyone is saying the different LAB sims they were asked in the exam, BUT are the SIMLET type questions still in the exam? where you have to answer serveral multichoice questions after running commands in a lab?

There were EIGRP and OSPF mentioned a few months back?
Thanks!

hi @original_zomby congrtas!!

respect to – OSPF SIM – virtual Link configuration this is https://www.digitaltut.com/route-ospf-sim or https://www.digitaltut.com/route-ipv6-ospf-virtual-link-sim ??

I tried multiple audio lectures including video lectures for the preparation of 300-101 certification exam but that all was in trivial. Then I found ROUTE 300-101 PDF guide on braindumpscerts.com with these practice questions, I passed the 300-101 exam. The best benefit is a 100 % success rate. I highly recommend this to everyone who wants to pass the 300-101 exam on the first try. Good luck everyone

@NEED HELP QUICK

Simlets are also called Evaluation, since you evaluate the Network.

And yes the Standard Labs and the Simlets can be in the Exam, it completely random which lab or simlet will come up sometimes you get no simlet sometimes you get both (EIGRP and OSPF).

Just learn all labs which you can find on this site.

@Destroyer
Well done mate! Congrats.

Could I please ask, is this correct regarding the brand new “IPV4 Virtual Link / Stub Sim”?

1 – Configure a virtual link over the transit area (was area 11)
2 – Remove any old bad config (e.g. virtual link put in wrong place?)
3 – Configure OSPF process ID x on all routers
4 – Configure OSPF on the network links with network command “x.x.x.x 0.0.0.3 area X”
5 – Test connectivity with a ping
6 – Block all inter area and external routes – This is done on R3 /Area 30 with stub no-summary)

Anything to add?

@Alex
Looks like its a new sim which is a mixture of both you mentioned :)

I had 3 sims which were ospf sim, eigrp sim and ospf and eigrp redistribution.

All labs same as here but just different IPs and they mentioned the ospf process for the ospf sim.

All other questions same as 195q

@Worried
Thanks and congrats!
For the OSPF sim, do you have to configure OSPF on them from scratch? in the digitaltut gns3 sim OSPF is already setup and it just says:
Your task is to configure the following:
Portland’s S0/0 interface in Area 1
Amani’s S0/1 interface in Area 1

If it is telling you which process to use, surely there cant be OSPF setup when you start?

Would like to get the complete new sim setup in lab any exact topology and questions(what needs to be done)

please:

Which two statements about the enable secret and enable password commands are true? (Choose two)
A. I both commands are missing from the global configuration,vtp lines use the console password
B. The enable secret command overrides enable password
C. The enable password command has a stronger encryption algorithm than enable secret
D. The enable secret commmand is bac kwards-compatible with more version of IOS
E. The enable secret and enable password commands must be used togerher

@memo
A,B

@Mstff
thank you

Anyone here taking the exam in the Philippines? ..

QUESTION 428
Which three functionalities are specific to stateful NAT64? (Choose Three)
A. It requires IPv4-transalable IPv6 address
B. It requires either manual or DHCPv6 based address assignment for IPv6 host.
C. It helps ensure end-to-end address transparency and scalability.
D. A state or bindings are created on every unique translation.
E. It conserves IPv4 addresses.
F. No constraint is put the number of endpoints due to 1:N translation
Correct Answer: BDE
Section: Networking – Valid-September

It think the answer for this question is DEF
from table 2 in this link:
https://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/enterprise-ipv6-solution/white_paper_c11-676278.html

B may refer to STATELESS NAT64

@Domino
Good work! Completely agree.

I have to attempt the watchguard Firebox Essential Exam is there any body who guide me regarding any website or blog and forums for dumps and discussion . just like this forum

This one keeps getting asked, and everyone always ends up with EIGRP.

Q555. which protocol use both best path and second best path for traffic??
a. EIGRP b.OSPF c.BGP d.RIP
Marked answer A EIGRP

I think it could be BGP…
https://tools.ietf.org/html/rfc6774
The best-path (main) reflector plane distributes the best path for each route as it does today. The second plane distributes the second best path for each route, and so on.

@Domino
thanks for you reference , DEF completely true .

Q-414

If this configuration is applied to a device that redistributes EIGRP routes into OSPF. which two statements about the behavior of the device are true? (Choose Two )
A. EIGRP routes appears in the routing table as E2 OSPF routes
B. The device router ID is set to Loopback0 automatically
C. The device redistributes all EIGRP networks into OSPF
D. EIGRP routes appears in the routing table as N2 OSPF routes
E. The device redistributes only classful EIGRP networks into OSPF.
F. EIGRP routes appears as type 3 LSAs in the OSPF database.

A – E oh C – E
Please help!!

Any forum or website just like this forum for watchguard Please let me know thanks