Share your ROUTE v2.0 Experience

passed with 95x.
labs same as digital tut. be careful about the subnets, ip’s.
networking 757 dump is valid. not sure all of them from 195 q. but sure from 757 q dump.
thanks to networking. You great!!!

Please who enter exam this days cntact me cause i have exam on 23september

Thanks Exact2pass.com, You are the perfect match for exam. I used it and found my exam very easy to attempt.I could not share the level of my happiness.

Exact2pass is definitely a key to success. I suggest it to all students if you want pass in exam then used this

share witm me a dump please

Ultel93 @gmail.com

@Nneettwwoorrkkiinngg
Q363
Which two statements about Frame Relay Point-to-Point connections are true? (Choose Two)

A. Changing a point-to-point sub interface to a different type requires the device to be reloaded.
B. They use two DLCIs to communicate with multiple endpoints over the Frame Relay cloud.
C. The device can establish a point-to-point connection to the cloud without a DLCI.
D. They can operate normally without a DLCI map.
E. Each physical interface that extends to the Frame Relay cloud can support a single SVC.
Correct Answers marked as A and B.

Dont think this is right, 99% sure you dont need to reboot after changing the interface type so thats A out, B seems correct, so need to pick one more.
I think D, so B&D ?

@Nneettwwoorrkkiinngg

Can you Help me understand the Dnd on URPF

The option is really unclear

It permits only packets that are received on the same interface as the exit interface for the destination address

@TheMightyThor

URPf works by enabling a router to verify the reachability of the source address in packets being forwarded.

When administrators use Unicast RPF in strict mode:
1. the packet must be received on the interface that the router would use to forward the return packet.
2. Unicast RPF configured in strict mode may drop legitimate traffic that is received on an interface that was not the router’s choice for sending return traffic.
3. Dropping this legitimate traffic could occur when asymmetric routing paths are present in the network.

“It permits only packets that are received on the same interface as the exit interface for the destination address”

So if a packet (for a destination) was NOT sent out of the the interface it came in on, then it will not be permitted to come back in. Its simply used to stop packets coming in with spoofed source addresses.

Q: 363
What two statements about Frame Relay point-to-point connections are true? (Choose two)

TO . Changing a secondary point-to-point interface to a different type requires that the device be reloaded.
B. They use two DLCIs to communicate with multiple endpoints over the Frame Relay cloud.
C. The device can establish a point-to-point connection to the cloud without a DLCI.
D. They can operate normally without a DLCI map.
E. Each physical interface that extends to the Frame Relay cloud can support a single SVC.

Correct answers: E – A
A 100% , E 60%
PLEASE CONFIRM

Passed today, Nneettwwoorrkkiinngg Q195 legit. If you know the topics you can easily pick out the wrong answers but it helps to sharpen your skills.

Recommend you can complete the 9tut sims and DND with no problem before taking the test.

@LJ
Q: 363
What two statements about Frame Relay point-to-point connections are true? (Choose two)

A. Changing a secondary point-to-point interface to a different type requires that the device

Correct answers: E – A
A 100% , E 60%
PLEASE CONFIRM

Have you labbed this? are you 100% sure the router needs rebooting?
I cant find anywhere that supports this either?

Well done DUAL!!!!

@CCNP-2017 & LJ

Once you create a specific type of subinterface, you cannot change it without reloading the router. For example, you cannot create a multipoint subinterface serial0.2 and then change it to point-to-point. To change it, you need to either reload the router or create another subinterface. This is the way the Frame Relay code works in Cisco IOS software.

http://www.ciscopress.com/articles/article.asp?p=170741&seqNum=5

@Destroyer

then the correct answer is A and E ??

@Destroyer
Brilliant! Thank you

@LJ

didnt read your question properly the first time.

D. They can operate normally without a DLCI map. << the term DLCI map is confusing
E. Each physical interface that extends to the Frame Relay cloud can support a single SVC

but based on the below:

"a single VC is always provisioned for a point-to-point connection. The same VC originates at a local end and then terminates at the remote end."

Point-to-Point Interfaces can terminate only a single VC and each pair of sub-interface must have a unique subnet.

"only one DLCI can be configured per point-to-point subinterface."

"On point-to-point subinterfaces, you do not need to use the frame-relay map command to perform static address mapping, because it is always assumed that the end point of the point-to-point connection automatically resides on the same subnet as the start point"

http://www.ciscopress.com/articles/article.asp?p=170741&seqNum=6

so A & E – in my opinion

“a single VC is always provisioned for a point-to-point connection. The same VC originates at a local end and then terminates at the remote end.”
Point-to-Point Interfaces can terminate only a single VC and each pair of sub-interface must have a unique subnet.

“only one DLCI can be configured per point-to-point subinterface.”
“On point-to-point subinterfaces, you do not need to use the frame-relay map command to perform static address mapping, because it is always assumed that the end point of the point-to-point connection automatically resides on the same subnet as the start point”

http://www.ciscopress.com/articles/article.asp?p=170741&seqNum=6

so A & E – in my opinion

@@Nneettwwoorrkkiinngg

Can you please tell me that in valid September 195 dumps which answers are correct in vce file , there are two answers , one is answer and other is correct answer , which one is correct ?

QUESTION 644
Which two statements about EVN are true?
A. It supports IPv6 traffic.
B. It can support up to 16 VNs.
C. It uses redistribution to share routes between VNs.
D. It supports SSM only.
E. A configuration can be based on an existing VRF configuration

A-E oh B-E
Please help!!!!!!

@LJ

the correct answer is A and E

“a single VC is always provisioned for a point-to-point connection. The same VC originates at a local end and then terminates at the remote end.”
Point-to-Point Interfaces can terminate only a single VC and each pair of sub-interface must have a unique subnet.

“only one DLCI can be configured per point-to-point subinterface.”
“On point-to-point subinterfaces, you do not need to use the frame-relay map command to perform static address mapping, because it is always assumed that the end point of the point-to-point connection automatically resides on the same subnet as the start point”

http://www.ciscopress.com/articles/article.asp?p=170741&seqNum=6

**
QUESTION 644

A predefined EVN known as “vnet global” is on the device

The vnet global is also known as the default routing table.

IPv6 traffic is supported in vnet global only

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/evn/configuration/xe-3s/evn-xe-3s-book/evn-overview.html

A-E

Q: 363

A – E

Point-to-Point Interfaces can terminate only a single VC and each pair of sub-interface must have a unique subnet.

QUESTION 644

A – E

A predefined EVN known as “vnet global” is on the device
The vnet global is also known as the default routing table.
IPv6 traffic is supported in vnet global only

wont let me post more details :P

TheMightyThor

@CCNP-2017 Thank you for giving time to explain that. So much clearer to me now.

The option is stating that “it permits packets that are received on an interface, if the source of the packet is reachable by the interface that the router received it on” henceforth -> strict mode

cisco is so making harder questions on how they ‘word’ the questions

QUESTION 658
Refer to the exhibit.
You want router r1 to perform unequal-cost routing to the 172.168.10.0/24 network.
What is the smallest EIGRP variance value that you can configure on R1 to achieve this result?
A. 1
B. 2
C. 3
D. 4
Correct Answer: C
Section: Networking – Valid-September

this answer is incorrect, the correct answer is: B. 2

Does anyone have dump for lab sims 300-101? My exam is on 27 sept…I need help here :(

Just cleared the ROUTE 300-101 exam on the first attempt, here’s my score 1000/940 my friend suggested me braindumpscerts.com for my ROUTE 300-101 exam preparation, I would like to thanks to @anna & braindumpscerts for the updated & valid exam study material. Good Luck!

@Jessamine which labs did you get & congrats mate :)

@LJ
QUESTION 658
Refer to the exhibit.
You want router r1 to perform unequal-cost routing to the 172.168.10.0/24 network.
What is the smallest EIGRP variance value that you can configure on R1 to achieve this result?
A. 1
B. 2
C. 3
D. 4
Correct Answer: C
Section: Networking – Valid-September

this answer is incorrect, the correct answer is: B. 2

That would mean they were both equal. The feasibility condition isn’t matched if it equal I thought. So 3 would work?

@LJ -QUESTION 658 i will need to make a small lab to test this however i have feeling it will be C

Question 175 >> Marked A but should be C

A network engineer is enabling RIPng on a new customer link. Under which configuration mode is RIPng enabled?

A. Global
B. Router
C. Interface
D. IPv6

Answer: A

Explanation

In order to enable RIPng, we have to do it under global configuration mode. For example:

R1(config)#ipv6 router rip RIPNG_DIGITALTUT

Then we enable RIPng on each interface: << ENABLE RIPng

R1(config)#interface Ethernet 0/0
R1(config-if)#ipv6 rip RIPNG_DIGITALTUT enable
R1(config-if)#exit
R1(config)#interface loopback 0
R1(config-if)#ipv6 rip RIPNG_DIGITALTUT enable

Which value determines the amnount of traffic that a network path can hold in transit?
Marked answer is:
MSS

But wouldnt the correct answer is “Bandwidth Delay Product”

“bandwidth-delay product is the product of a data link’s capacity and its round-trip delay time. The result, an amount of data measured in bits, is equivalent to the maximum amount of data on the network circuit at any given time”

@Nneettwwoorrkkiinngg, the 95 questions mentioned here many times, is it the 1st 95 questions in your latest update?

Thanks in advance

@CCNP-2017

Yes you are 100% correct:

Which value determines the amount of traffic that a network path can hold in transit?

Answer is “Bandwidth Delay Product”

MSS defines the maximum amount of data that a host is willing to accept in a single TCP/IP datagram.

Chapter 5: Advanced EIGRP Concepts 183

The following list summarizes the key points to know about variance:
■ The variance is multiplied by the current FD (the metric of the best route to reach a
subnet).
■ Any FS routes whose calculated metric is less than or equal to the product of variance
and FD are added to the IP routing table, assuming that the maximum-paths
setting allows more routes.
■ Routes that are neither successor nor feasible successor routes can never be added to
the IP routing table, regardless of the variance setting.
When the routes have been added to the routing table, the router supports a couple of
methods for how to load-balance traffic across the routes. The router can load-balance
the traffic proportionally with the metrics, meaning that lower metric routes send more
packets. Alternately, the router can send all traffic over the lowest-metric route, with the
other routes just being in the routing table for faster convergence in case the best route
fails.

@LJ

Question says – “You want router r1 to perform UNEQUAL-COST routing to the 172.168.10.0/24 network.”

I might be wrong but…..
If it was variance 2 then the current FD * a variance of 2 would be 300.
The cost to ROUTER3 is also 300 so this would this be equal cost load sharing?

if the varienace was 3, then the FD*3=450, so now the FS would be less than 450 (it would be 300) and this would be used for unequal cost load balancing.

@LJ

I think C is correct

We have to realise that:

In this question the FD of the successor is 150 (from R1 to R2) and the FD of the feasible successor is 300 + 150 = 450 ( R1 – R3 – R2 ) not just 300

This is assuming the network 172.168.10.0/24 is connected to R2 and costs are as follows: R1-R2 = 150, R2 – R3 = 150 & R1-R3 = 300

Thus if you just use a variance of 2 it will no longer be equal to 450 hence need variance of 3

@Destroyer
Great stuff! Again!

@ erika please send me your dump at bluestackexam01 @ gmail. com

hi friends,

Which adverse circumstance can the TTL feature prevent

in nneettwwoorrkkiinngg dump the answer is “routing loops”
in 192q dumps, the answer is “DoS attacks”

what is the true answer please

Which adverse circumstance can the TTL feature prevent:

The TTL expiry behaviour creates a denial of service (DoS) attack vector against network equipment. << Creates not prevents HOWEVER ..

TTL Security Check feature for multihop BGP Peering Sessions helps prevent DoS attacks.

TTL prevents a data packet from circulating indefinitely <> as the question mentions the TTL feature

https://www.cisco.com/c/en/us/about/security-center/ttl-expiry-attack.html
https://www.cisco.com/c/en/us/td/docs/ios/12_2sx/feature/guide/fsxebtsh.pdf

Which adverse circumstance can the TTL feature prevent:

Answer: “DoS attacks”

as the question mentions the TTL feature

I agree with @Destroyer, for a feasible successor to be included in the routing table (to perform unequal load balancing) the equation below must be satisfied:

(FD of the successor)*(variance) must be greater than or equal to (FD of the feasible successor).

Hence, variance is 3

thanks destroyer

A network engineer applies the command ip tcp adjust-mss under interface configuration mode. What is the result?

answer “C. The probability of dropped or segmented TCP packets is decreased.”
or “D. The optimum MTU value for the interface is set.”

??

QUESTION 363
Which two statements about Frame Relay Point-to-Point connections are true? (Choose Two)
A. Changing a point-to-point subinterface to a different type requires the device to be reloaded.
B. They use two DLCls to communicate with multiple endpoints over the Frame Relay cloud.
C. The device can establish a point-to-point connection to the cloud without a DLCI.
D. They can operate normally without a DLCI map.
E. Each physical interface that extends to the Frame Relay cloud can support a single SVC.
Marked answer : AB

I think it’s A,E

Support for “A”

“Once you create a specific type of subinterface, you cannot change it without reloading the router. For example, you cannot create a multipoint subinterface serial0.2 and then change it to point-to-point. To change it, you need to either reload the router or create another subinterface. This is the way the Frame Relay code works in Cisco IOS software”

Link: http://www.ciscopress.com/articles/article.asp?p=170741&seqNum=5

Support for “E”

“On point-to-point subinterfaces, you do not need to use the frame-relay map command to perform static address mapping, because it is always assumed that the end point of the point-to-point connection automatically resides on the same subnet as the start point. It is also not required to enable or disable Inverse ARP, because there is only a single remote destination on a point-to-point PVC and discovery is not necessary.”

LINK: http://www.ciscopress.com/articles/article.asp?p=170741&seqNum=6

A network engineer applies the command ip tcp adjust-mss under interface configuration mode. What is the result?

Answer: The probability of dropped or segmented TCP packets is decreased

The ip tcp adjust-mss command helps prevent TCP sessions from being dropped by adjusting the MSS value of the TCP SYN packets.

https://www.cisco.com/en/US/docs/ios-xml/ios/ipapp/command/ip_tcp_adjust-mss_through_ip_wccp_web-cache_accelerated.html#GUID-68044D35-A53E-42C1-A7AB-9236333DA8C4

For the question with variance I think it is 1 only ? it doesn’t satisfy the condition of the AD (candidate for FS) < FD (successor) in this case it is 150 < 150. Please correct me if I'm wrong. I just saw this one on Jeremy's video.

@Mosh – I will be taking exam in PH as well when will be your exam ? :)

@Destroyer

for the question below I think it is C interface

A network engineer is enabling RIPng on a new customer link. Under which configuration mode is RIPng enabled?

A. Global
B. Router
C. Interface
D. IPv6

It seems that the question is just asking how to enable RIPng on “new customer link” I guess from that question the RIPng is already enabled on the router. You just have to enable it on the “new link” :)

Hi all,

I have passed with 9xx. The dumps posted are valid.

All questions from the sept 195q dump by Nneettwwoorrkkiinngg

got 3 labs [ redistribute, eigrp stub and ospf stub]
3 d&d [aaa, acls, loose&strict]

Also thanks for ulloading the vce simulator with crack. This helped alot in the prep. I was able to set it to exam mode and prune to the 195q only. Great stuff keep up the good work.

All questions from the sept 195q dump by Nneettwwoorrkkiinngg

got 3 labs [ redistribute, eigrp stub and ospf stub]
3 d&d [aaa, acls, loose&strict]
please share with me

dipen@@@@6085 at gmail.com

Hi Guys,

Passed the exam few days ago with 96x. I must say that Questions from nneettwwoorrking is still valid, especially the 195Q. But I study all of the nneettwwoorrking dumps to be sure. Don’t need to study SPOTO as the questions from SPOTO can be seen in nneettwwoorrking dumps. I’ll be sharing a link for the labs I used, I edited some of them for troubleshooting purposes but did put a note. Or you can download them from this site :). I also studied dumps from PassLeader 300-101″Will also share the link”.

Just to share, I felt that I was going to fail the exam due to some bugs. 1st bug I encountered is the OSPF sim, after configuring the right relationship with AMANI and Portland, I was able to ping the loopback behind Lynaic. Now It’s time to make the Area between Portland and Amani a Totally Stub, after doing that I was not able to ping the loopback behind Lynaic. So I thought I did something wrong and negate all the command I did but the Default route is still there even I undo the the Totally stub command. I was so frustrated and did troubleshoot it for 1 hour and didn’t see anything wrong with the configs so I decided just to put the right commands even though I wont be able to ping the loopback.

2nd Bug I encountered is the EIGRP stub sim, the requirement is to summarize the routing table so it only contains two 10.0.0.0 subnets. So the best mask you could use is 255.255.240.0, but this wont work, routes wont summarized it, it will still has 9 subnets. But I read the 9tut explanation and on that page they uses 255.255.0.0, so I did try and luckily it was summarized to 2 subnets.

But besides having encountered those problems I got 96x, so it seems that cisco is just looking for a specific commands for their requirements. I hope this help you guys.

nneettwwoorrking – https ://drive . google .com/drive/folders/1Cf4MHTm8Qt5-_jYzJt6PXNy6b6YOBEx1

PassLeader/SPOTO/Labs/Sim – https : //drive .google . com/open?id=1zJDrby2chdjZTBT1Aani3zAvMouR6MlD

Goodluck to all of you :)

Hello @JAJA

Would you say the 195q should be enough with the labs to pass? I got my exam on Wednesday and worried like sick.