Share your ROUTE v2.0 Experience

@ELO

You have old vce or pdf files
please bro upgrade it

@networkkkkkkking

Which Three Questions You make updated ?

@Ahmet
Contact with me
nneettwwoorrkkiinngg @ gmail.com

Hi guys in q709 the answer is C “reflexive acl”, isn’t it?

@ELO

QUESTION 695
Which routing protocol routers traffic throught the best path and seccond best path at the same time?
A. EIGRP
B. BGP
C. OSPF
D. RIP

THE Ans BGP

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_bgp/configuration/xe-16/irg-xe-16-book/bgp-additional-paths.html

best 2 or best 3 (best 2 means the bestpath and 2nd best path; the 2nd best path is the one computed by eliminating best-path from the best-computation algorithm. Similarly, best 3 means the bestpath, 2nd best path, and 3rd best path; the 3rd best path is the one computed by eliminating bestpath and 2nd best path from the best-computation algorithm.)

In the last dump q195 the answer is A eigrp for q695.

QUESTION 428
Which three functionalities are specific to stateful NAT64? (Choose Three)

Ans BDE, It should be DEF, B is wrong.

B. It requires either manual or DHCPv6 based address assignment for IPv6 host.

Only Stateless NAT64 “Requires either manual or DHCPv6 based address assignment for IPv6 hosts NOT stateful64 , So I think Instead of B it should be F. No constraint is put the number of endpoints due to 1:N translation

refer https://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/enterprise-ipv6-solution/white_paper_c11-676277.html

Anyone know if you can use question mark or tab in labs on exam?

which labs are the most common right now? Do you think one needs to study for all gns3 labs available on this site?

@ nneettwwoorrkkiinngg @digitaltut

thank you so much ! passed today CCNP Route congratulations.

R_L_A congrats Are you working networking august dump ?

@R_L_A
Congratulations :) I am happy that hear

Please Contact with me
nneettwwoorrkkiinngg @ gmail.com

300-101 exam passed today, 990 points
5 D&D – COPP/MPP, GRE Tunnel, ipv6 security, frame-relay and AAA features
3 Labs – EIGRP STUB, Redistribute EIGRP/OSPF, ospfv3 virtual-link

195q is super valid, but we have some wrong.
Thanks @nneettwwrrookkiinngg and @digitaltut

@Alvaro
congratulations Bro
Where is some wrong?
please contact with me
nneettwwoorrkkiinngg @ gmail.com

@nneettwwrrookkiinnggg, please see correction below

QUESTION 638
What happends when unicast flood protection is triggered on a VLAN?
A. The VLAN is shut down
B. Traffic on the VLAN is load-balanced across multiple links
C. The VLAN is removed from the VLAN database
D. Traffic on the VLAN is passed to another VLAN with lower load
Correct Answer: D

I think the answer is A based on this:
Most switches implement no special command to detect flooding. Catalyst 6500/6000 Supervisor Engine 2 and higher series switches running Cisco IOS System software (Native) version 12.1(14)E and higher or Cisco CatOS system software version 7.5 or higher implements ‘unicast flood protection’ feature. In short, this feature allows the switch to monitor the amount of unicast flooding per VLAN and take specified action if flooding exceeds specified amount. Actions can be to syslog, limit or shutdown VLAN – the syslog being the most useful for flood detection. When flooding exceeds the configured rate and the action configured is syslog, a message similar to the following will be printed:

%UNICAST_FLOOD-4-DETECTED: Host 0000.0000.2100 on vlan 1 is flooding
to an unknown unicast destination at a rate greater than/equal to 1 Kfps

Link is:
https://www.cisco.com/c/en/us/support/docs/switches/catalyst-6000-series-switches/23563-143.html

@nneettwwrrookkiinnggg, this one I think is wrong too

QUESTION 615
Which two causes of latency are true? (Choose two)
A. High bandwidth on a link
B. Split horizon
C. Propagation delay
D. Serialization delay
E. Under-utilizaion of a link
Correct Answer: CE

I think it’s C,D based on this link

https://www.ccexpert.us/network-design-2/causes-of-delay.html

MASH is right. Q615 Should be CD

hi guys, please help :
Which LSA type does R3 propagate into Area 1 for the 192.168.10.0/24 network?(can’t paste the exhibit,but hopefully u know what Im talking about )
A. type 3 LSA
B. type 5 LSA
C. type 7 LSA
D. type 10 LSA
type 5 or 7 is the correct answer? I’ve seen both in 2 different dumps.

It’s B, type 5 LSA

Hi guys I passed the exam yesterday Sept.10 with 944 score, 195q in Networking is very valid I think almost all the questions are there but I still studied all Questions in nneettwwrrookkiinnggg’s VCE/PDF just to be sure :) I have taken my exam here in Philippines.

Thanks bro @nneettwwrrookkiinnggg you’re a big help! :)

Hello , can anyone send me a new dumps on route? quaderat1 at yahoo dot com

@ShutNoShut, Thank you for the update. I will also take the exam in the Philippines. What sims are in the exam?

That’s me ^,

Thanks for the update @ShutNoShut. people who took/are taking the exam in recent/coming days please let us know if only nneettwwrrookkiinnggg’s 195q is enough to pass. thanks in advance & good luck everyone

Hey guys I am taking test today in a couple of hours and will share. Just wanted to point out that MOST OF THE PASSING POSTS IN HERE ARE FAKE!!!! Don’t trust their results and their links just go by the people in here you know are real and will actually respond like @nneettwwrrookkiinnggg and other people trying to clear up answers. Too many spammers!

@nneettwwrrookkiinnggg

plz help me i need dump 300 115 you have ?

Hi Guys, Passed the exam yesterday with 9xx/1000
All the questions are from the Sept section of networkkkkkkking and I think there’re some wrong answers but not sure which. No need to study any-other sections and Sept section is only enough to pass the exam

4 Labs and 4 D&D are from the spoto 146q

@Cloud_Network
plz send me link spoto 146q

@67MOCCNP and @Osmi

NSSA areas do not allow type 5 external LSAs
R3 will pass the type 7 into area 1, then R2 will translate it to a type 5 ans pass to area 0

It asks about R3 into Area 1 – So answer is Type 7

Can anyone else confirm is Sept section of networkkkkkkking 195q enough or do you need to review other sections?

can any one send spoto 146q link

can anyone share the spoto dump?
Labs from spoto or digital tut? if digital tut is enough labs please tell me.

we need some information about the labs? digtut seems to be enough tho?

Guys @Spoto dumps there is many answers are wrong now @Networrrrkiiiiiiiiing dumps are reliable .

Hi All
My dump is valid
I have been working my dump for 5 months
I just help you
What do you want to do?

https: // drive.google.com/drive/folders/1Cf4MHTm8Qt5-_jYzJt6PXNy6b6YOBEx1

@ShutNoShut

Congratularions Bro
I am happy to heard that.
Good luck

@Alvaro
Congratulations Bro :)

q736

a packet capture indicates that the ruoter is not forwarding DHCP packets that it receives on the itnerface fa0/0.

which command needs to be entered in global conf mode to resovle this issue

a. ip helper-address
b. i…
c. ….
d. ip forward-protocol

A solves the issue , it forwards dhcp and other protcols, with ip forward.protocol you have to choose which ones to forward to to not forward if no ip forward
protocol is used with ip helper-address.
both couldbe correct but A is more general I think

which one is the correct cisco answer?

Different answer in networkingg. and spoto dumps.

Q. which snmp verification command shows the encryption and authentication protocols that are used in SNMPV3?

A. Show snmp group spoto answer
B show snmp user networking answer

Q.Company is deploying multicast application must be accessible between sitesbut must not be accessible outside of the organization.?

a.FF02:/16 spoto
B.FF08:/16 Netttworking

which one right.?

@Anonymous
ip helper address must configuration on interface
careful the Questions

@kaleem
Multicast address FF08:/16

@kaleem
Different answer in networkingg. and spoto dumps.

Q1. which snmp verification command shows the encryption and authentication protocols that are used in SNMPV3?
A. Show snmp group spoto answer
B show snmp user networking answer

ANSWER:
Here is the output of that command…
Router# show snmp user
authuser
User name: authuser
Engine ID: 00000009020000000C025808
storage-type: nonvolatile active access-list: 10
Rowstatus: active
Authentication Protocol: MD5
Privacy protocol: DES
Group name: VacmGroupName

Q2.Company is deploying multicast application must be accessible between sitesbut must not be accessible outside of the organization.?
a.FF02:/16 spoto
B.FF08:/16 Netttworking
which one right.?

ANSWER:
Both are multicast addresses, but the question states “accessible outside of the organization”

FF02 is for link-local multicast
FF08 is for organization local multicast

Incorrect…
QUESTION 638
What happends when unicast flood protection is triggered on a VLAN?
A. The VLAN is shut down
B. Traffic on the VLAN is load-balanced across multiple links
C. The VLAN is removed from the VLAN database
D. Traffic on the VLAN is passed to another VLAN with lower load
Correct Answer: D

The unicast flood protection feature can send an alert when a user-defined rate limit has been exceeded. It can also filter the traffic or shut down the port generating the floods when it detects unknown unicast floods exceeding a certain threshold.

So the answers of limit, alert (via syslog) or shutdown would all be correct.

Hello CCNP-2017 AND nneettwwrrookkiinnggg

Could you guys help with the following 5 questions please?

QUESTION 552
which condition prevents the establishment of a DMPVN tunnel between two spokes ?
A. HSRP is enabled on the spoke devices
B. IPsec is enabled on the spoke devices
C. the two spokes are behind different PAT devices
D. the two spokes have different tunnel keepalive settings.
Correct Answer: D
Keepalives does not need to match, the tunnel key should match. So the answer should be C

QUESTION 675
A network engineer is enabling RIPng on a new customer link Under which configuration mode is RIPng enabled?
A. Global
B. Router
C. Interface
D. IPv6
Ans A or C

QUESTION 616
Which two causes of latency are true? (Choose two)
A. High bandwidth on a link
B. Split horizon
C. Propagation delay
D. Serialization delay
E. Under-utilizaion of a link
Correct Answer: CE or CD

QUESTION 711
On a Frame relay, we are unable to ping the remote router, how to solve the problem?
A. DLC is active
B. DLC is not active and deleted
C. Frame Relay map is configured
D. Need and ACL to allow PING
Correct Answer: C. Question ask about how to solve the problem so the ans may be C

QUESTION 737
Refer in the exhibit. A packet capture indicates that the router is not forwarding the DHCP packets that it receives on interface FastEthernet0/0. Which command needs to be entered in global configuration mode to resolve this issue?
A. ip helper-address
B. ip DHCP relay
C. service DHCP
D. ip forward-protocol
Correct Answer: A? ip helper-address applied under interface config mode, the question ask about Global config mode. Ans Should be D

@nneettwwrrookkiinnggg,

Thanks for all the good work Bro.

I have a request if you can split the the 195 questions into 3 sections please. As I am trying to use vce to practice, but I cannot select range of questions from the 195q for example 1-30 questions.

Also do you have the labs please.

Thanks

@nneettwwrrookkiinnggg, I think this has wrong answer too.

QUESTION 547
what are the two correct statements about enable secret and enable password command
A. the enable password command has a strong encryption algorithm than enable secret
B. if both commands are missing from the global configuration, vty lines use the console password
C. the enable secret command is backwards compatible with more versions of IOS
D. the enable secret and enable password commands must be used together
E. the enable secret command overrides enable password

Correct Answer: CE

I think it’s B,E .

“If neither the enable password command nor the enable secret command is configured, and if there is a line password configured for the console, the console line password will serve as the enable password for all VTY (Telnet and Secure Shell [SSH]) sessions.”

Link here:
https://www.cisco.com/c/en/us/td/docs/ios/12_2/security/command/reference/fsecur_r/srfpass.html

@nneettwwrrookkiinnggg,

Thanks for all the good work Bro.

I have a request if you can split the the 195 questions into 3 sections please. As I am trying to use vce to practice, but I cannot select range of questions from the 195q for example 1-30 questions.

Also do you have the labs please.

Thanks

Ok so took the test and failed. 7XX/1000 passing is 790 so I’m disappointed BUT I can tell you STUDY NHRP NAT64 NPT64 EVN DMVPN AND KNOW IT WELL! I was blindsided by a bunch of questions good luck everyone

@PL
Bro you shoul update files
You are studying my old files :)

labs are still from digital tut ? right?