Share your ROUTE v2.0 Experience

I concur with others today. I didn’t pass, but I got the EIGRP Stub Sim, EIGRP OSPF Redistribution Sim and IPv6 OSPF Virtual Link Sim.

Quite a few questions from the “New Updated Questions” section here.

A lot of Layer 2 and VPN questions.

Good luck to all!

Hi, I just wanna know if you failed exam and retake it after 5 days will cisco give u different set of questions or just the same?

where to networkinggggg dumps..?

Hi Guys please help me, can someone share a clear answers for EIGRP OSPF Redistribution LAB??

@JAJA

also both questions were in my exam :) lucky you :)

QUESTION 31 of SPOTO or QUESTION 680 of nneettwwoorrkkiinngg

interface gi 2/0/0
vnet trunk
ip address 192.168.1.1 255.255.255.0
vnet name cisco

Which effect of this configuration is true?
A. It designates the interface as a GRE tunnel endpoint
B. it configures 802.1q trunking on the interface
C. I designates the interface as an EVN trunk
D. I removes VTP from the interace

Correct Answer: C for nneettwwoorrkkiinngg >> I answered C
Correct Answer: B for SPOTO

==============

Q703 and Q547 has the same question?, just the phrasing is different . If so, what would be the correct answer? .

For Question 703, I noticed that this is VTP lines . VTP is virtual trunking protocol right? . Let’s say this is VTY, is it still correct to choose A ?

QUESTION 703
Which two statements about the enable secret and enable password commands are true? (Choose two)
A. I both commands are missing from the global configuration,vtp lines use the console password
B. The enable secret command overrides enable password
C. The enable password command has a stronger encryption algorithm than enable secret
D. The enable secret commmand is bac kwards-compatible with more version of IOS
E. The enable secret and enable password commands must be used togerher

Correct Answer: AB >> This is correct

QUESTION 547
what are the two correct statements about enable secret and enable password command
A. the enable password command has a strong encryption algorithm than enable secret
B. if both commands are missing from the global configuration, vty lines use the console password
C. the enable secret command is backwards compatible with more versions of IOS
D. the enable secret and enable password commands must be used together
E. the enable secret command overrides enable password

Correct Answer: CE

@ShutNoShut

did you follow the exact steps mentioned here in the Lab Sim section?

Passed today:) I thought my score would be better (<900)considering I had a few repeat questions from the last exam, used this site and some other sources and found a few conflicting answers which popped up. 3 Labs, redistribution, virtual link, EIGRP. Think I cocked up on EIGRP summary, I think the subnet mask has to be more specific for it to work properly (255.255.240.0 not 255.255.0.0). I was going to try it but forgot, I ended up entering eigrp 100 stub summary on router 4 to be able to see 2 summary routes on router 3 which looked like it worked. The more I think about it the more I think it was wrong. Think I’ll lab it up tonight as it’s bugging me lol

@nneettwwoorrkkiinngg

QUESTION 607
Which is an invalid command/keyword when configuring redistribution (Choose Two)
A. tag
B. access list
C. route map
D. ther (valid) option
Correct Answer: BC

i think the correct answer is A and D , because we can use route tag and route map when we configure redistribution

@HAGAR, thanks man for the update… lucky me,haha….

Do you happen to have the EIGRP Simlet?, not the EIGRP Eval or EIGRP/OSPF Redistribution. Can’t find it anywhere on this page. The one with the questions like this:

Question 1
Which two networks does the Core1 device have feasible successors for? (Choose two)

Question 2
Which three EIGRP routes will be installed for the 172.17.3.128/25 and 172.17.2.0/24 networks? (Choose three)

Question 3
Which three networks is the router at 172.17.10.2 directly connected to? (Choose three)

Could you send it to JAJAJA9122 @ gmail . com

Thanks
JAJA

@Hagar

I created the whole LAB in GNS3 and seems the details in the show interface lab here in digitaltut are wrong as I got the same details in my own LAB same answer on the Lab Sim. Understand it now clearly, thanks a lot!

but seems the route is asymmetric, R1 to R4’s loopback goes to R1>R2>R4 and R4’s loopback to R1 route is R4>R3>R2>R1

@JAJA
@Hagar

Are the Simlets still included in the exam? TIA

Hi All,

Any thoughts on this, is this correct? . I think the answer is B.

QUESTION 743
What is the output of the following command:
show ip vrf
A. Show’s default RD values
B. Displays IP routing table information associated with a VRF
C. Show’s routing protocol information associated with a VRF.
D. Displays the ARP table (static and dynamic entries) in the specified VRF

Correct Answer: A

@ShutNoShut,

Better to study everything :)

could someone provide the answer to this question AND a source for proof.

QUESTION 654
Which two statements about NAT in a DMVPN environment are true?(Choose two)
A. a hub router can be behind a dynamic NAT on a device.
B. Spoke routers can reside only on the public side of a NAT device.
C. Two spokes can establish session among themselves using PAT behind different NAT devices.
D. A spkoke router can be represented by a static NAT on a device.
E. A hub router can user static NAT for its buplich UP address.

@JAJA

here you go https://www.digitaltut.com/route-eigrp-simlet :)

@nneettwwoorrkkiinngg

in v2 , same Qs with different ans:

QUESTION 645
Which two statements about EVN are true?
A. It supports IPv6 traffic.
B. It can support up to 16 VNs.
C. It uses redistribution to share routes between VNs.
D. It supports SSM only.
E. A configuration can be based on an existing VRF configuration
Correct Answer: CE

QUESTION 603
Which two statements are true about EVN? (Choose Two)
A. A configuration can be based on an existing VRF configuration
B. it supports IPv6 traffic
C. It can support up to 16 VNs
D. It uses rdistribution to share routers between VNs
E. It supports SSM only.
Correct Answer: AB

ans 645 is correct :
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/evn/configuration/xe-3s/evn-xe-3s-book/evn-shared-svcs.html

@ShutNoShut, I have that one. What I don’t have is the GNS3 file for that, maybe you have that one?.

@All, Maybe you got the GNS3 file for this sim
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/evn/configuration/xe-3s/evn-xe-3s-book/evn-shared-svcs.html

Thanks,
JAJA

@nneettwwoorrkkiinngg how can I use the VCE simulator. The crack is failing for me. Can you please assist me with this? Every time that I try to install it is failing.

I know others have had some issues with this. I’m running windows machine. Is there any solution to this?

answer for this question please with proof please . anyone?

QUESTION 536
Which three methods can a network engineer use to fix a metric based routing loop in the network.
A. A.Implement offset lists at network boundaries
B. B. Filter routes manually using distribute lists
C. C. Filter routes manually using prefix lists
D. D. Implement proper network summarisation on key routing points
E. E. Filter routes based on tags
F. F. Utilise root database filters
Correct Answer: ABE – not sure about this in nnneettwoorkkinnng 2.1

this question apparently doesn’t have an answer, according to the link below it should be AUTHPRIV which provides DES. This is not an option…

QUESTION 664
Which SNMP model and level can provide DES encryption?
A. SNMPV2 noAuthNoPrry
B. SNMPV3 authNoPriv
C. SNMPV3 authEn
D. SNMPV3 noAuthNoPrv
Correct Answer: C

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/snmp/configuration/xe-3se/3850/snmp-xe-3se-3850-book/nm-snmp-snmpv3.html#GUID-F55D3AA7-91EE-4BAE-948C-03DAB75A3E72

@acme

you are right, there is mistake in the q

did anybody figure out how to use the cracked VCE?? Please let me know how to get it work?

@nneettwwoorrkkiinngg how can I use the VCE simulator. The crack is failing for me. Can you please assist me with this? Every time that I try to install it is failing.

I know others have had some issues with this. I’m running windows machine. Is there any solution to this?

thank you abdularahmansh

anyone, answer to this questions and proof?

QUESTION 666
Which location within the network is preferred when using a dedicated route for Cisco IP SLA operations?
A. user edge
B. provider edge
C. access edge
D. distribution edge

@Anonymous I dont think you will be eligible for the 300-101 if you let your CCNA expire because it is a prerequisite. This is what I found in the Cisco forums and that is why I renewed by CCNA so I could still have the option to take 300-101. Not sure if answers will be the same. I doubt they would but there are a couple versions of 300-101 so you might luck out

question 401 -it asks for ‘technology’ – read link below first paragraph. answer should be C VRF Lite

QUESTION 401
Which technology is required on an EVN trunk interface?
A. 802.1q
B. NAT
C. VRF-Lite
D. IS IS
https://www.cisco.com/c/en/us/products/ios-nx-os-software/easy-virtual-network-evn/index.html

@nneettwwoorrkkiinngg

QUESTION 675
A network engineer is enabling RIPng on a new customer link Under which configuration mode is RIPng enabled?
A. Global
B. Router
C. Interface
D. IPv6
Correct Answer: A

ans should be C

@nneettwwoorrkkiinngg

QUESTION 678
Which two statements about ICMP unreachable messages are true?(Choose two
A. They are sent when a route to the destination is missing from the routing table
B. They can be enable and disable on a device only on a global level
C. They are sent when a destination address responds to an ARP request
D. They include the entire packet so that the source can identify the process that generated the message
E. They include a poriton of the original data so that the source can identify the process that generated the message
Correct Answer: AC

i think the ans is AE :
http://www.networksorcery.com/enp/protocol/icmp/msg3.htm

@RouteReady
Hi bro
please send mail what is the problem

@networrrrrkkkkiiiiinnnnnnnnnnnnggggggggggggggggggggggggg

Please check the below Duplicate Questions in your PDF file . Please update

Q556 & Q588 . Same Question

Q547 & Q702 . Same Question

Q394, Q504 & Q720 . Same Question

Q379, Q477 & Q658 . Same Question

Q422, Q495 & Q527 . Same Question

Q537 & Q672 . Same Question

@abdulrahmansh
Hi all and abdlrahmansh
What do you think correct answer?

1(config)#ipv6 router rip RIPNGTEST <—A. Global
R1(config-rtr)#exit
R1(config)#interface fastEthernet 0/0
R1(config-if)#ipv6 rip RIPNGTEST enable <—C. Interface
R1(config-if)#exit
R1(config)#interface loopback 0
R1(config-if)#ipv6 rip RIPNGTEST enable

https: // networklessons.com/ipv6/how-to-configure-ripng-on-cisco-ios-router/

QUESTION 675
A network engineer is enabling RIPng on a new customer link Under which configuration mode is RIPng enabled?
A. Global
B. Router
C. Interface
D. IPv6

@Ahmed hi bro
thanks I am checking now

RIPng is for ipv6 and it’s enable on interface.

https://www.cisco.com/c/en/us/td/docs/switches/metro/me3600x_3800x/software/release/15-4_3_S/configuration/guide/3800x3600xscg/RIPng_IPv6.pdf <= Page 3.

in global config is for customizing ipv6 RIP

Hi nneettwwrrookkiinnggg,

QUESTION 690
How can you minimize unicast flooding in a network?
A. Configure HSRP on two routers, with one subnet preferred on the first router and a different subnet preferred on the second router.
B. Set the router’s ARP timeout value to be the same as the timeout value for Layer2 forwarding table entries.
C. Set the router’s ARP timeout value to greater than the timeout value for Layer 2 forwarding table entries.
D. Set the router’s ARP timeout value to less than timeout value for Layer 2 forwarding table entries

Correct Answer: B >>> Should be D
learningnetwork.cisco.com/thread/117389

Hi All,

Any thoughts on this, is this correct? . I think the answer is B.

QUESTION 743
What is the output of the following command:
show ip vrf
A. Show’s default RD values
B. Displays IP routing table information associated with a VRF
C. Show’s routing protocol information associated with a VRF.
D. Displays the ARP table (static and dynamic entries) in the specified VRF

Correct Answer: A

Good day everyone! I want to thank you all for your good feedback. A special thanks goes out to nneettwwrrookkiinnggg for all his efforts. His dump is valid, and helped me tremendously in passing. I passed the exam earlier today with 8XX score. For the lasbs, I got the EIGRP/OSPF redistribution, IPV6 Virtual-Link, and EIGRP stub. I did not have any SIMS. Drag and drops were COPP/MPP, IPV6 ACL, frame relay, and GRE. All questions came from his dump, including a mix of old (august) and newer questions. If you put in your time, fully understand the concepts, you will pass! Good luck to all!

hi @KURO,

is “show run” working for the labs?

@JAJA,

QUESTION 743
What is the output of the following command:
show ip vrf
A. Show’s default RD values
B. Displays IP routing table information associated with a VRF
C. Show’s routing protocol information associated with a VRF.
D. Displays the ARP table (static and dynamic entries) in the specified VRF

A is correct. I run the show command myself and saw default RD values, interface and VRF names

^that’s me

@Mosh…Yes, I was able to use Show run in all the labs.

@KURO, is write mem or copy r s working?. – Thanks

@Anonymous, thanks for the feedback

MARKED ITEMS(1/09 – 4:09PM) – OK
SPECIAL COURSE – OK
Networking DnD – OK
Networking August – OK
PassLeader (1-end) – OK
Networking Day1, Day2, Day3
Networking Day4, New Q.
Labs

Marked this Items:

Ask to Digitaltut
Q.743 – P.205
Q.690 – Tell Networking to fix this – P.205
Q.184 and Q.620 – P.205

QUESTION 40
Lab Simulation 1 – OSPF
QUESTION 41
Lab Simulation 2 – EIGRP Stub
QUESTION 42
Lab Simulation 3 – IPv6 OSPF Virtual Link
QUESTION 43
Lab Simulation 4 – Policy Based Routing
QUESTION 44
Lab Simulation – EIGRP OSPF Redistribution
QUESTION 45-49
EIGRP Sim
QUESTION 50-53
OSPF Sim

@nneettwwoorrkkiinngg,

Q.184 and Q.620 has the same Question but different Answers. I think the right answer is Choice B. because choice A. has ACL includes UDP instead of TCP. At first, I was also hesitant to choose choice B as the correct answer because the question indicates outbound traffic and choice B indicates “ip access-group 102 in. But as I think about it, you could also apply in on your LAN side router as “in” so it could never go out your WAN interface.
Please delete one.

Q.184 – Correct Ans. A –> Should be B.
Q.620 – Correct Ans. B

Which configuration can you apply to a device so that it always blocks outbound web traffic on Saturdays and Sundays between the hours of 1:00 AM and 11:59 PM?

A. time-range SATSUN periodic Saturday Sunday 1:00 to 23:59
access-list 102 permit udp any any eq 80 time-range SATSUN
access-list 102 permit tcp any any eq 443 time-range SATSUN
interface Vlan303
ip address 10.9.5.3 255.255.255.0
ip access-group 102 out

B. time-range SATSUN periodic Saturday Sunday 1:00 to 23:59
access-list 102 permit tcp any any eq 80 time-range SATSUN
access-list 102 permit tcp any any eq 443 time-range SATSUN
interface Vlan303
ip address 10.9.5.3 255.255.255.0
ip access-group 102 in

Any thought on this ?

@nneettwwoorrkkiinngg,

Q.184 and Q.620 has the same Question but different Answers. I think the right answer is Choice B. because choice A. has ACL includes UDP instead of TCP . At first, I was also hesitant to choose choice B as the correct answer because the question indicates outbound traffic and choice B indicates “ip access-group 102 in. But as I think about it, you could also apply in on your LAN side router as “in” so it could never go out your WAN interface.
Please delete one.

Q.184 – Correct Ans. A –> Should be B.
Q.620 – Correct Ans. B

Which configuration can you apply to a device so that it always blocks outbound web traffic on Saturdays and Sundays between the hours of 1:00 AM and 11:59 PM?

A. time-range SATSUN periodic Saturday Sunday 1:00 to 23:59
access-list 102 permit udp any any eq 80 time-range SATSUN
access-list 102 permit tcp any any eq 443 time-range SATSUN
interface Vlan303
ip address 10.9.5.3 255.255.255.0
ip access-group 102 out

B. time-range SATSUN periodic Saturday Sunday 1:00 to 23:59
access-list 102 permit tcp any any eq 80 time-range SATSUN
access-list 102 permit tcp any any eq 443 time-range SATSUN
interface Vlan303
ip address 10.9.5.3 255.255.255.0
ip access-group 102 in

Any thought on this ?

@nneettwwoorrkkiinngg

Q.641 Drag and Drop;

Answer: são as frases entre ()

interface Ethernet0
ip address 10.1.1.2 255.255.255.0

interface Serial0

! Serial interface config
no ip address

(encapsulation frame-relay)

frame-relay lmi-type ansi
! subinterface config

(interface Serial0.1 multipoint)

ip address 192.168.1.5 255.255.255.240

(frame-relay map ip 192.168.1.1 100 broadcast)

@nneettwwoorrkkiinngg

Q.641 Drag and Drop;

Answer: are the sentences between ()

interface Ethernet0
ip address 10.1.1.2 255.255.255.0

interface Serial0

! Serial interface config
no ip address

(encapsulation frame-relay)

frame-relay lmi-type ansi
! subinterface config

(interface Serial0.1 multipoint)

ip address 192.168.1.5 255.255.255.240

(frame-relay map ip 192.168.1.1 100 broadcast)

@KURO, what country did you take the exam? do we still need to type “copy run start” to save the config?

@KURO, in EIGRP stub, did you use “ip summary-address eigrp 123 10.2.0.0 255.255.0.0”? Some said in the forun that we need to narrow down the subnet mask to just include the subnets in the problem. I am confused

@nneettwwoorrkkiinngg

QUESTION 693
Company is deploying a multicast applic ation that must be accessible between sites, but must not be accessible outside of the organization
Based on
A. FF00:/16
B. FFOE:/16
C. FF02:/16
D. FF08:/16
Correct Answer: C

ans must be D, same as q 543

Hello all

I finally passed the exam this week (990/1000)

All the questions, D&D and labs were from these dumps (updated on August 2018)

drive.google.com/open?id=15LxO7JIEaIj_x6T14snLKbsI8J8RYkJQ

The PDF and VCE Simulator are still valid and stable

No need to learn more

Hi All,

Can someone help me share the lab gns files, i tried downloading from digital tut but i’m unable to open them in my gns 2.1.8

Thank you

@nneettwwoorriinngg

Waiting for your help as you committed with me. I have no time. I have send you mail. But your are not replying my email??
When you need my help, I help you and your friends. But now I need your help you are not even reply to my email??
I am very much disappointed for yourside.