Share your ROUTE v2.0 Experience

congrats @DataRT, thanks for sharing the new qs too.

Congrats DataRT.
what command did you use to ping between R1 & R4 in the IPV6 ospf virtual link sim. Did it work or did you just use the show ipV6 route on R1 to check for the loopback address of R4 in R1

@ raden
What did you mean by “Loopback0 should be the one pinged from portland on the labs” for the ospf sim. Are we to ping the loopback address or the ip address? i am a bit confused. Please explain with the command. Thank you

Just a show command “show ipv6 route” on R1 would suffice.

as tut explained on the labs section, you should be able to ping the loopback inteface of Lynaic from Portland once you have configured it.

i’ve tried ipv6 ospf virtual link on the lab, and initially, if you use “show ipv6 route ospf” on R1, there are no routes advertised. once you have extablished virtual link between R2 and R3, the ipv6 addresses of R2 R3 and R4 should appear once you use “show ipv6 route ospf” again

1. Where to place a Cisco IP SLA in a network
A.Distribution edge
B.Access Edge
C.User Edge
D.Provider Edge
—————–
2.How EIGRP metric is calculated
A.Bandwidth+Delay
B.Bandwidth*Delay
C.Bandwidth-Delay
D.Bandwidth/Delay
——————
3.What will be the maximum data device A would send to device B, when host A has values MTU of 1500 and MSS of 4000;
and host B with MTU of 19000 (can’t remember the exact value) and MSS of 32000 4000
A.?
B.?
C.?
D.?
——————-
4.Cause of latency
A.High bandwidth on a link
B.Unsaturated link
C.Serialization delay
D.something.. delay
——————-
5.Commands to configure GRE over IPSEC
A.ip mtu
B.tunnel key
C.ip tcp adjust mss
D.mpls mtu
——————-
6.Enable secret encryption type
A.7
B.5
C.MD5
D.other options
——————-
7.ICMP redirect (read about how it works)
something like:load balancing on two routers with destination address in their routing table
A.
B.
C.
D.
——————-
8.Something about EVN edge interface function
A.
B.
C.
D.
——————-
9.Something about troubleshooting PAP and CHAP
A.debug ppp authentication
B.debug ppp negotiation
C.
D.
——————-

Hi everone

New .VCE file is ready for all attend the exam
if you know new questions please sent me a mail
I can add the new vce file
my mail : nneettwwoorrkkiinngg @ g m a i l. com
this is last dump and valid
drive.google.com/drive/folders/1Cf4MHTm8Qt5-_jYzJt6PXNy6b6YOBEx1

Update date : 19-07-2118

1. QUESTION 442
2. NEW QUESTION 133
3. DRAG & DROP – 32
4. EIGRP & OSPF Simlets – 8
ALL IN ONE_v1.0

1. Where to place a Cisco IP SLA in a network
A.Distribution edge
B.Access Edge
C.User Edge
D.Provider Edge
my answer is A
do you agree with me?

Hey guys, i’m sitting my exam tomorrow, will let you know how it goes.

In case anyone wants them, my answers to DataRT’s new questions:
1 – D
2 – A (256*(Bandwidth+Delay))
4 – C
6 – C

@nneettwwrrookkiinnggg this should be Q9
Question: 399
Which two debug commands can you use to view issues with CHAP and PAP authentication? (Choose Two)
A. debug tacacs
B. debug ppp authentication
C. debug radius
D. debug aaa authentication
E. debug ppp negotiation
Answer: BE

2.How EIGRP metric is calculated
A.Bandwidth+Delay
B.Bandwidth*Delay
C.Bandwidth-Delay
D.Bandwidth/Delay
my answer is A
do you agree with me?

i think so too, BW + delay should be it

For default behavior, you can simplify the formula as follows:

metric = bandwidth + delay

https://www.cisco.com/c/en/us/support/docs/ip/enhanced-interior-gateway-routing-protocol-eigrp/16406-eigrp-toc.html

@ DataRT and raden
Thank you so much for your help

@Marco , Goodluck , please let us know for any new questions , thanks

might not make it to complete the new questions DataRT posted as my exam’s in a few hours, but i’ll try to cover up as much as i can. nneettwwrrookkiinnggg’s compiling it on a new version of all-in-one

Raden,

Good Luck!

@raden
Good Luck to you. Let us know how it goes.

31. OSPF has R1 router ID 172.18.1.1 . What happens when R1 configure with a new loopback interface IP address 172.17.1.1 ?
a. OSPF chooses 172.17.1.1 as new router ID when R1 is rebooted.
b. OSPF chooses 192.168.21.0 as new router ID when apply new configuration.
c. OSPF chooses 172.17.1.1 as new router ID when apply new configuration.
d. OSPF retains 172.18.1.1 as router ID until interface on which is configured goes down
Answer: D

is this correct? I think answer is a

When OSPF is forming an adjacency, in which state, the actual exchange of information in the link ?
A. INIT
B. loading
C. exstart
D. exchange
Correct Answer: B

also this is c isn’t it?

cleared exam Yesterday with 9XX thanks digitaltut

Hi Anyone here who can share the link of CBT Nuggets CCNP Route video?

Your help is highly appreciated. Thank you guys.

2.How EIGRP metric is calculated
A.Bandwidth+Delay
B.Bandwidth*Delay
C.Bandwidth-Delay
D.Bandwidth/Delay

My answer is D

sorry should be Bandwidth + Delay

In which scenario can asymmetric routing occur?
A. active/active firewall setup
B. single path in and out of the network.
C. active/standby firewall setup
D. redundant routers running VRRP

Correct Answer: D
– i think the correct answer is a, active/active firewall setup

passed with 8xx
>lots of new questions, I’ve encountered 15-20 new ones, its as DataRT has posted.
>also up to 10 questions which were reworded by cisco but is really in the all-in-one (THERE ARE LOTS OF REWORDING, USE STOCK KNOWLEDGE AS MUCH AS POSSIBLE)
>i’ve also encountered old questions from jazzy477 last june.
>DnDs are also in all-in-on, but take note that they rearrange the choices which appear so review much.

There’s a new DnD which i encountered
Accounting -> option
Authentication -> challenge….
Authorization -> option
Radius -> utilizes udp port or something
Tacacs+ -> utilizes tcp port or something
this was not included at 31qs dnd by jazzy, but might be included on other

feeling good as i can now proceed to the second one, tshoot maybe. see you guys on the other site.

PS most updated dumps is nneettwwoorrkkiinngg v31 by page 170

Hi All,

@nneettwwrrookkiinnggg did a great job compiling all dumps into a single one.

The only little thing is that the pdf has problems with some images (Q441 for example). would you please export it using a different page size or orientation??

well, collaborating with the site, my two cents are in:

1. Where to place a Cisco IP SLA in a network
A.Distribution edge
B.Access Edge
C.User Edge
D.Provider Edge

ANS D (It will be better if it is “Service Provider Edge” instead of “Provider Edge”)

Source:

“With these requirements in mind, the Enterprise can then concentrate on selecting device pairs that make sense. In general, the source device should be the router located at the edge, or the boundary where the Enterprise network meets the service provider’s network. If there are other routers along the path that are also in the managed domain, then a device pair to source can be configured from these routers as well. Thus, users can obtain a more granular view of the service levels across the network.”

//www . cisco.com/ en/US /technologies /tk869/ tk769/ technologies_white_paper0900aecd806bfb52 .html

2.How EIGRP metric is calculated
A.Bandwidth+Delay
B.Bandwidth*Delay
C.Bandwidth-Delay
D.Bandwidth/Delay

Obviously A

5.Commands to configure GRE over IPSEC
A.ip mtu
B.tunnel key
C.ip tcp adjust mss
D.mpls mtu

Ans B (It should be Tunnel protection … but if it’s only one choice I’ll try my luck with that one)

I am pass route today
First of all
thank you nneettwwrrookkiinnggg Zam2u and other user’s which help us to become better than we were
in exam have 3 labs
ospf eigrp redistribute
eigrp sim
ospf sim ( in my exam process id 68 area 4)
this link all labs (remove space)
http : / /www. digitaltut. com/practice-real-route-labs-with-gns3

dnd and questions
this links remove space
https : //drive .google .com /drive/folders/1Cf4MHTm8Qt5-_jYzJt6PXNy6b6YOBEx1
good luck and see you on ccnp switch

@ccnp
Congrats and thank you , do you remember any new question ?

@Nik
unfortunately I do not remember new questions
these questions were simple

Today passed with 9xx score. I got old labs and old Drag Drops. approx 8 new MCQ.
I remembered 3 mcqs.

1
Which two statements are true about EVN ?
A. A configuration can be based on an existing VRF configuration
B. it supports IPv6 traffic
C. It can support up to 16 VNs
D. It uses rdistribution to share routers between VNs
E. It supports SSM only.

2
Which can an EIGRP router send when a route goes into the Active state ?
a.query
b.reply
c.request
d.hello
e.update

3.
what happens when a router receives a packet with a TTL of 0 ?
a. the router sends an ICMP Destination Unreachable Message to the host that sent the packet.
b. the router attempts to forward the packet along an alternate path in the routing table
c. the router flags the packet and forwards it to the next hop
d. the router sends an ICMP Time Exceeded Message to the host that sent the packet

I passed my exams yesterday,this forum has been heplful and thanks to everyone who shared the stuff.had new questions on drag and drop on Copp and Mpp

@all those who passed the exam recently can you guys please share the config commands for all labs if possible. I have a exam on tuesday.

Hi guys,

I just passed with 9xx

I had about 5/6 new questions, EIGRP OSPF Redistribution Sim with fast ethernet link (requiring distance command), OSPF Sim and EIGRP Stub Sim. Some area id’s and process id’s different, but all labs exactly as on this site. All old DNDs from dumps.

New questions:

1. Which can an EIGRP router send when a route goes into the Active state ? (actually the wording was different but i got this question). You had to give 2 answers for this question.
a.query
b.reply
c.request
d.hello
e.update

2. RIPng failing to update?
a. Firewall between routers or TCP 520 blocked
b. Firewall between routers or UDP 520 blocked
c. Firewall between routers or TCP 521 blocked
d. Firewall between routers or UDP 521 blocked
(Answer D)

3. I got the question that DataRT posted:

Host A has values MTU of 1500 and MSS of 4000; and host B with MTU of 19000 (can’t remember the exact value) and MSS of 32000 (Also MSS sizes were different between hops across link)

Question says Host A cannot talk to Host B (with diagram). How to resolve. One of the answers was ‘configure PMTUD’ which is the one I chose. Another option was to reduce MSS size of host A.

4. Which is an invalid command/keyword when configuring redistribution:
a. tag
b. access list
c. route map
d. other (valid) option
I answered B.

Also several questions reworded from dumps so understand concepts. However if you know the dumps well, it’s definitely enough to pass easily.

Good luck guys and thank you for all your contributions. If you find this site helpful, please help others when you sit the exam.

@Marco – Well done!

How many DnDs did you get and what were they?

1
Which two statements are true about EVN ?
A. A configuration can be based on an existing VRF configuration
B. it supports IPv6 traffic
C. It can support up to 16 VNs
D. It uses rdistribution to share routers between VNs
E. It supports SSM only.

ANSWER = ?
2
Which can an EIGRP router send when a route goes into the Active state ?
a.query
b.reply
c.request
d.hello
e.update

ANSWER =A
3.
what happens when a router receives a packet with a TTL of 0 ?
a. the router sends an ICMP Destination Unreachable Message to the host that sent the packet.
b. the router attempts to forward the packet along an alternate path in the routing table
c. the router flags the packet and forwards it to the next hop
d. the router sends an ICMP Time Exceeded Message to the host that sent the packet

ANSWER =A

4. Which is an invalid command/keyword when configuring redistribution:
a. tag
b. access list
c. route map
d. other (valid) option

ANSWER = B

Hi All,

Which is the correct answer? B or C???

QUESTION 206 When OSPF is forming an adjacency, in which state, the actual exchange of information in the link ?
A. INIT
B. loading
C. exstart
D. exchange

Thanks Digitaltut..Passed CCNP Route with score 920+ …Two guys shared 40 & 66 questions within last 5/6 pages…all of them were in the exam…..DND :CoPP and MPP was there ..IPV6 Router Security Featurs…GRE feature….FraneRealy Multipoint…
EIGRP Stub….OSPFV3….EigrpOSPF Redistribution…Total 60 question
I have read all the Kikavich file..they are still very valid…………………….
My CCNP Certification is Complete…..CCNP Route was my last part………….Again Special thanks to digitaltut and everyone in this forum…

@nneettwwrrookkiinnggg

This question is wrong, the answer is 240s (Flush Time) so I think you have to correct the answer D.

QUESTION 602
a question for RIPv2 how long a static route remains if the point to point interface is down.
A. 30s
B. 60s
C. 180s
D. 180s

Correct Answer: D

@Nasir

Although the adjacency is formed in the exstart state, the actual exchange of routing information is performed in the loading state. Answer B

//www. computernetworkingnotes.com/ccna-study-guide/ ospf-neighbor-states -explained-with-example .html

Note: That’s why when OSFP is full converged and all routing info is exchanged IOS logging message states “OSPF Change from Loading to full”

I want to do gns3 labs
Please if anyone has Cisco IOs please share with me fasto123 at gmail dot com

Hello Fasto,

Which IOS are you looking for?

Hello it_kid,

May you sen me the 44&66 question dump to me?

k2far4me at hotmail.com
thank you

With only 3.5 hours of overnight sleep, I sat for the exam this morning.

I got the EIGRP OSPF Redist sim on my first few questions AND I GOT CONFUSED AND SKIPPED RIGHT THROUGH IT WITHOUT EVEN realizing what I was doing. Thinking that I was now doomed to fail, I went through very disheartedly through the next 59 questions.

Yet, I passed! Thanks to all of you awesome people on this forum.

Lab: EIGRP Redist, OSPFv3 virtual-link, Eigrp Stub

The Virtual-link lab was very confusing because as soon as I took out the uneeded virtual-link between R4-R3, the neighbor adjacency went down yet the loopback from R4 would show up in R1.

Almost all questions were from the content folks have shared on this forum.

Maybe a new question:
What benefit does TTL provide?
correct answer is Loop prevention

DNDs: ipv6 access-class – traffic filter, CoppMpp, frame-relay multipoint, others that I don’t remember…

Off to Switching!

Good Job @Happy!! How much do you score without the Sim? You should have a solid exam besides that unfortunate skip.

@R’hllor
Thanks I fixed
and 240s

@R’hllor

Thanks! I scored 860+

Hi,
I’ve passed all CCNP exams now I need help for writing a resume. Does anyone know the site or link to download a sample resume?

ManyThanks in advance.

Hi all I am creatind new vce adding new D&D and questions

@raden well done bro I am happy:)
@R’hllor resize page size bu should you stady vce file I give application in drive
@ccnp well done :)

@R’hllor
thanks bro

QUESTION 602
a question for RIPv2 how long a static route remains if the point to point interface is down.
A. 30s
B. 60s
C. 180s
D. 240s

Correct Answer : D

I got test later 11 am. wish me luck guys. I woke up very early again