Share your ROUTE v2.0 Experience

@Syn @Bunns did ur exam go well ?

Also, don’t remember letters as the answers. They moved the answers to new letters/positions in the test.

@syn congrats my friend. for the questions, were they the same to what was posted on the forum or were they newer?

@Syn congrats & thx for the help

They were a mix of Digitaltut, Kikivich, and the newer questions that we discussed. There were like three maybe four that were newer but I was shook taking the test after the blown lab and the power outages. Glad they had a UPS on the computer because I thought my life flashed before my eyes when the room went dark.

There were a good number from the questions we posted here. I will try to get the DnD up.

@syn thanks. hopefully you can remember the newer ones that we did not cover. I’m assuming that you got the frame relay lmi D&D

DnDs:

1. mGRE, MSS, IPSec, keepalive, Tunnel Key

2. Int S0—-> encap frame relay——–>Int S0.1 multipoint———->frame relay map 192.168.1.1

3. AAA. Options were Radius, TACACS, Authentication, Authorization, Accounting

4. Drawing a blank on the last one.

@rnfl

did you get questions you pasted in the exam?

pls clarify

thanks

@rnfl

did you get questions you pasted in the exam?

pls clarify

thanks

@rnfl & @all

iam preparing a pdf file containing all posted questions and answers and i will share it with you as soon as @rnfl confirms my above question.

thanks

@Curious

Hate to say it but Tuesday of last week Cisco made a ton of money because they released new questions and set the test at 60 questions. If all you studied were the dumps you were screwed. The number of new questions seems to be more than enough to make a test by itself. The vast majority seems to be new MC questions. There seems to be a few new DnDs. Glad I am in before they do a new set of Lab questions.

Just done and dusted. Labs are all valid dnd’s half new half seen before here, mcq’s … thanks to the last few pages here because most questions were new and from them plus about half a dozen i had never seen before. That said due to study, and common sense I could usually work out the likely correct answer. Big ups for the owners of this site and $15 well spent. Also thanks to the posters here especially around the new questions. I will try later to give some examples of questions I had later. …

which condition prevents the establishment of a DMPVN tunnel between two spokes ?
a. HSRP is enabled on the spoke devices
b. IPsec is enabled on the spoke devices
c. the two spokes are behind different PAT devices
d. the two spokes have different tunnel keepalive settings.
answer is c.

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_conn_dmvpn/configuration/xe-3s/sec-conn-dmvpn-xe-3s-book/sec-conn-dmvpn-dt-spokes-b-nat.pdf

• If one spoke is behind one NAT device and another different spoke is behind another NAT device, and Portr Address Translation (PAT) is the type of NAT used on both NAT devices, then a session initiated between the two spokes cannot be established.
One example of a PAT configuration on a NAT interface is:
ip nat inside source list nat_acl interface FastEthernet0/1 overload

Had a frame relay multipoint dnd that I had never seen and struggled with no idea if I was correct. It was steps and commands to configure it so brush up on that

@ and, those are good ones!, I remember them being on there…has anyone found the vnet question!?

@Hallfawi

No, these are compiled from 477Q and previous comments exam questions

@anonymous you probably got the same frame relay question as Syn. Interface, encap, sub interface and ip

Yep sounds like it. @Madmartigan yep I had the vnet global question

@Madmartigan

I had the vnet global question as well.

@anonymous @Syn what is the vnet global question? Sorry hehehe i’m brained dead now.. being studying all the material all day today. Any other pointers from you guys? My turn to pass this thing hehehe

Is this the one?

After reviewing the EVN configuration, a network adminstrator notices that a predefined EVN, which is know as “vnet global” was configured. What is the purpose of this EVN? Or what is the purpose of ‘vnet global’?

A. It defines the routing scope for each particular EVN edge interface
B. It aggregates and carries all dot1q tagged traffic
C. It refers to the global routing context and correspondants to the default RIB
D. It safeguards the virtual network that is preconfigured to avoid mismatched routing instances

Answer: C

@Mario

After reviewing the EVN configuration, a network administrator notices that a predefined EVN, which is known as “vnet global” was configured. What is the purpose of this EVN?

A. It defines the routing scope for each particular EVN edge interface.
B. It aggregates and carries all dot1q tagged traffic.
C. It refers to the global routing context and corresponds to the default RIB. <<<<<<<<<<
D. It safeguards the virtual network that is preconfigured to avoid mismatched routing instances.

I wanted to ask Mario. I was on the T-shoot board to see what was up and there was a Mario there. Are you that Mario or is there a shadow clone there?

@Syn its a clone lol because i’ve helped in the ccna r/s ccna security and ccda forums. Once im done here i’ll probably run into that Mario lol..

So was this the question you were referring to on the test?

Yep…….there is a good chance you will see it.

Don’t make the mistake I made. Practice the labs. I can’t believe I blew a lab but I was so worried about the MCQ I didn’t give the attention I was planning to the labs. I even called myself out on it this morning and this past weekend but I still passed and that is the most important part.

I was considering for a while doing the CCDA/CCDP and still have CCNA Sec on the peripheral certs to do one day but aren’t on the main radar. I want to finish up CCNP…..maybe do CCIE written but get Data Center and later on Collaboration. Somewhere in all that learn Python and maybe Ansible.

@Syn i’ve already completed NP security and 2 tests in datacenter but want to finish up the r/s NP and IE this year.

I’ve already mastered all the labs and most of the d & d. I’ve also been prepping on the questions. I feel comfortable on those, its just the mcq i’m actually stuck on. I’ve been studying both ROUTE and SWITCH in parallel. So, if all goes well friday, i’ll probably take a stab at SWITCH next friday.

@Mario

I may hit you up later for Security and definitely Data Center. I hope to do T-Shoot soon.

That is bold and ballsy. Switch wasn’t that bad. I took it fairly recently. The were some long ass labs. I read that the Switch questions were revamped on Terrible Tuesday as well. Good luck if you attempt.

We should keep going to IE. I want to try the IE written at least.

The vast majority of MCQs should be out now. I think I saw two or three that weren’t listed but don’t remember them. Nothing stood out about them.

Yep no problem.
So, from all the list that was made of all the questions. Would you say 90% were on the test?

hello everyone, my exam is next week i will try my best to memorize all the new Qs and then i will mention here.

@Sandy, i will take an exam next week same to you if u got new questions please share me

1 A network access serve using TACACAS+ for AAA operations receives an error message from the TACACS+ server. which action does the network access server take next ?

a. It attempts to authenticate the user against RADIUS
b. It restarts and attempts to reconnect to the TACACS+ server
c. It rejects the user access request the
d. It checks the method list for an additional AAA option
ANSWER :D ?

2.Which type of Netflow information is displayed when the show ip flow export command is executed?

A. top talkers
B. local status and statistics
C. sent status and statistics
D. export interface configurations

Correct Ans: C OR B

3. Multicast application must be accessible between sites, but not be accessible outside of the organization. Based on the scoping requirements, the multicast group address for the application will be allocated out of which range?

a. FF00::/16
b. FF08::/16
c. FF02::/16
d. FF0E::/16
answer: b???

4.Which routing protocol searches for a better route through other autonomous systems
to achieve convergence ?
a. Link-state
b. Hybrid
c. Path vector
d. Distance vector
answ :A???

5. VPN support for IPv4 and IPv6 address families. Which command enables a VRF that supports these requirements?

a. Router(config-vrf)#route-target 004:006
B. Router(config)#ip vrf CUSTOMER
C. Router(config)#vrf definition CUSTOMER
D. Router(config-vrf)#rd 004:006
ANS C

this correct answers ?

Hi all, passed the exam woo hoo!!

@someone I never saw any of those questions but:

All Lab’s here are still valid
About half the DnD’s are new, one that included tacacs, radius, authentication, accounting and authorization as options.
About 10 questions I had never seen before but most were ok to work out what the answers were.

That said I have sat the equivalent ccnp route (before it was called route) exam about 9 years ago and have been working as a Network Engineer for longer than that so I have quite a bit of learned knowledge, plus study etc… so don’t take this test lightly it was one of the toughest I have done.

I have a terrible memory for detail on these sorts of things but…

Some details I can remember:

New questions I have not seen before and I struggled with\still don’t know the answers:

Where do you enable RIPng?
interface config
something config
global config
router config
something else config

something about what has been included in eigrp for ipv6 choose 2
spf algorithm
then a bunch of other options … sorry not much help I know

Other random questions posted earlier that I saw:

5. What is EIGRP Summary Route Administrative Distance?
A. 90
B. 170
C. 5
D. 110
Answer: C

8. Which two OSPF router types can perform summarize in an OSPF network? (Choose two)
A. summary router
B. area border router
C. autonomous system boundary router
D. internal router
E. backbone router
Answer: B,C

9. In which two ways can split horizon issues be overcome in a Frame Relay network environment? (choose two.)
A. Configuring one physical serial interface with Frame Relay to various remote sites.
B. Configure a loopback interface with Frame Relay to various remote sites.
C. Configuring multiple subinterfaces on a single physical interface to various remote sites.
D. Enabling split horizon.
E. Disabling split horizon
Answer: C,E

10. Which two features does RADIUS combine? (choose two)
A. Telnet
B. Accouting
C. SSH
D. Authenticaiton
E. Authorization
Answer: D,E

13. Which three NTP operating modes must the trusted-Key command be configured on for authentication to operate properly? (Choose Three)
A. interface
B. client
C. peer
D. server
E. broadcast
Answer: B,D,E

14. Which two statements about Frame Relay LMI autosense are true on a Router? (Choose two)
A. It requires the LMI type to be explicitly configured.
B. It operates on Frame Relay DTE interfaces.
C. It operates on Frame Relay DCE interfaces.
D. It operates when the line is up by the line protocol is down.
E. It requires the line protocol to be up.
Answer: B,D

22. What is the default authentication in RIPv2 when authentication is enabled
A. SHA1 authentication
B. Enable password authentication
C. Plain text authentication
D. MD5 authentication
Answer: C

24. Where must a network engineer configure the ip helper-address command on a router
a. On the interface that will receive the broadcasts
b. On the DHCP configuration
c. the interface that is closed to the destination DHCP server
d. on the global configuration mode
Answer : A

30. Which two must you perform to enable a point-to-point Frame Relay connection ?
a. Configure the encapsulation type
b. Disable inverse ARP
c. Enable inverse ARP
d. Configure static address mapping
Answer:A

31. If device R1 has 1-Gigabit and 10-Gigabit Ethernet interfaces, which command do you enter so that it takes full advantage of OSPF costs ?
a. R1(config-router)#auto-cost reference-bandwidth 10000
b. R1(config-router)#auto-cost reference-bandwidth 10000000000
c. R1(config-if)# ip ospf cost 10000000000
d. R1(config-if)# ip ospf cost 10000
e. R1(config-route-map)#set metric 10000
f. R1(config-route-map)#set metric 10000000000
Answer:A

32. In which two areas does OSPF send a summary route by default ?
a. NSSA
b. Backbone
c. Totally stubby
d. Stub
e. Normal
Answer :C&D

34. Which three methods can a network engineer use to fix a metric based routing loop in the network.
a. Implement offset lists at network boundaries
b. Filter routes manually using distribute lists
c. Filter routes manually using prefix lists
d. Implement proper network summarisation on key routing points
e. Filter routes based on tags
f. Utilise root database filters

35. Which two features ara added in MSCHAP Version 2
a. Backwards-compatibility with MSCHAP version 1
b. Using the MD5 hash for stronger security
c. Ability to change an expired password
d. using 3 way handshakes for authentication
e. mutual authentication between peers

36. What does the following access list, which is applied on the external interface FastEthernet 1/0 of the perimeter router accomplish.
# access-list 101 deny ip 10.0.0.0 0.255.255.255.255 any log
# access-list 101 deny ip 192.168.0.0 0.0.255.255 any log
# access-list 101 deny ip 172.16.0.0 0.15.255.255 any log
# access-list 101 permit ip any any
#interface fastEthernet 1/10
#ip access-group 101 in
a. It filter incoming traffic from private address in order to prevent spoofing and logs any intrusion attempts
b. It prevents private internal address to be accessed directly from outside
c. It filters incoming traffic from private address ranges 10.0.0.0-10.0.0.255, 172.16.0.0-172.31.255.255, 192.168.0.0-192.168.255.255 and logs any intrusion attempts
d. It prevents the internal network from being used in spoofed denial of service attacks and logs any exit to the internet

37. What is the default authentication in RIPv2 when authentication is enabled
a. SHA1 authentication
b. Enable password authentication
c. Plaintext authentication
d. MD5 authentication

38. Which command sequence can you enter on a router to configure Unicast Reverse Path Forwarding in loose mode
a. Interface GigabitEthernet0/0
Ip verify unicast source reachable-via any
b. Interface GigabitEthernet0/0
Ip verify unicast source reachable-via loose
c. Interface GigabitEthernet0/0
Ip verify unicast source reachable-via all
d. Interface GigabitEthernet0/0
Ip verify unicast source reachable-via rx

41. Refer to the exhibit. After configuring GRE between two routers running OSPF that are connected to each other via a WAN link, a network engineer notices that the two routers cannot establish the GRE tunnel to begin the exchange of routing updates. What is the reason for this?
A. Either a firewall between the two routers or an ACL on the router is blocking IP protocol number 47. B. Either a firewall between the two routers or an ACL on the router is blocking UDP 57.
C. Either a firewall between the two routers or an ACL on the router is blocking TCP 47.
D. Either a firewall between the two routers or an ACL on the router is blocking IP protocol number 57.
Correct Answer: A

45. In which two ways can split horizon issues be overcome in a Frame Relay network environment? (choose two)
A. Configuring one physical serial interface with Frame Relay to various remote sites.
B. Configure a loopback interface with Frame Relay to various remote sites.
C. Configuring multiple subinterfaces on a single physical interface to various remote sites.
D. Enabling split horizon. E. Disabling split horizon.
Correct Answer: CE

49. A network engineer applies the command ip tcp adjust-mss under interface configuration mode. What is the result?
A. The probability of SYN packet truncation is increased.
B. The UDP session is inversely affected.
C. The probability of dropped or segmented TCP packets is decreased.
D. The optimum MTU value for the interface is set.
Correct Answer: C

oh btw there is 60 questions now as well

@Syn did you get the AAA question asking about local authentication before it over to radius or tacacs+?

Also, did you 1-2 questions regarding secret password used on the vty connections if a password is not set ? and the other overwriting the enable password.

@bunns congrats! The question how to enable ripng is in config-rtr interface. Its on the list of questions I believe.

As for the AAA, seems lime you and syn got the same D&D for that. What others did you get? Also, with all the questions posted in the forum, did you more of them or were the other questions pretty much from the old kikavich and all in one?

@Mario
Yeah random older ones most are from this site …mainly the “most common” and the “new updated” the USD$15 was well spent especially as it helped me nail down the LABs the get them done fast and not bog me down. If you have all of those down pat and you understand most of the concepts you can get enough of the questions right to pass. By the sounds of it you will knock it over ok Mario

@Syn thanks a lot for taking out time to explain it to me. I have already started studying the new questions. Congrats on the success of your exam.

@Bunns congrats on your exam. Planning to join the premium membership on this site as well as it helped a lot when i took my TSHOOT exam. I wanted to know if they also have the new questions that have been posted here already and what advice will u give as regards paying the $15. Thanks for your help

yep I had all the same DND’s as Syn

@Curious Thanks…
IMHO the $15 is well earned by the hosts just for them hosting this blog alone. But as for benefits for premium the online labs and practice tests are better than cisco approved paid ones costing over US$100 (believe me i purchased both) and they have really good explanations on most questions not just dumps so you actually learn the content.
Good luck

@Mario when will you test?

@Bunns Thanks a lot

@rnfl im taking it tomorrow

@bunns thanks i feel confident i’ll pass

@Mario good luck

anyone have answers for this questions ??

1-Which three methods can a network engineer use to fix a metric based routing loop in the network.
a. Implement offset lists at network boundaries
b. Filter routes manually using distribute lists
c. Filter routes manually using prefix lists
d. Implement proper network summarisation on key routing points
e. Filter routes based on tags
f. Utilise root database filters

2-What is a function of NPTv6?
A. It interferes with encryption of the full IP payload.
B. It maintains a per-node state.
C. It is checksum-neutral.
D. It rewrites transport layer headers.

3-Which two tasks must you perform to configure a BGP peer group ?
a. Configure the soft-update value
b. Set the advertisement interval
c. Assign neighbours to the peer group
d. Activate each neighbour
e. Activate the default route

4-which of the following situations results in a routing loop ?
a. when you have a single point of redistribution
b. when you use NAT translation on the edge of your network
c. when you implement contiguous IP routing blocks
d. when you implement noncontiguous IP routing blocks
e. when you have multiple points of redistribution

5-Which two features ara added in MSCHAP Version 2
a. Backwards-compatibility with MSCHAP version 1
b. Using the MD5 hash for stronger security
c. Ability to change an expired password
d. using 3 way handshakes for authentication
e. mutual authentication between peers

6. What are two limitations when in use of NPTv6 for lPV6 vs lPV6 Address translation?
A. stateful address translation
B. a limit of 32 1-to-1 translations
C. lack of overloading functionality
D. identify all interfaces NAT inside or outside
E. 1-to-1 prefix rewrite
F. mismatched prefix allocations

7-When use NPTv6 for IPV6 to IPV6 Address translation? (Choose two)
A. stateful address translation
B. a limit of 32 1-to-1 translations
C. lack of overloading functionality
D. identify all interfaces NAT inside or outside
E. 1-to-1 prefix rewrite
F. mismatched prefix allocations

@Sandy

1. ABE
2. D
3. CD
4. E
5. CE
6. CE
7. CE

@rnfl thanks alot

@syn, @bunns
Could you please recall the new dnds which came across to you in your exam and post on the comments section please.

Thanks

in an original exam at the Sims,
I dont take write memory or copy running-config startup-config … Is that normal?

@Fred, i had the-same problem.pls someone answer. couldn’t save my configurations with copy run or write memory?