Share your ROUTE v2.0 Experience

Which type of Netflow information is displayed when the show ip flow export command is executed?
A. sent status and statistics
B. top talkers
C. export interface configurations
D. local status and statistics
D or B

Hey guys, what are you using to study? Some of the questions that appeared up here are not in the CCNP Route book :/ ??? Thanks!

@Syn
how could i ever repay you……but utter thanks :)

Off study discussion……Done my Switch last year (back in june) and now Route on the way…Planning to get Tshoot out of the way this year too…..Not looking to do CCIE though as IT is full of news techs now, and I needed to load at least few of them including Azure and SDN in particular and for sure!

New questions PL help with the answers
1
Which two tasks must you perform to configure a BGP peer group ?
a. Configure the soft-update value
b. Set the advertisement interval
c. Assign neighbours to the peer group
d. Activate each neighbour
e. Activate the default route
2
which DHCP option enable to permit static routes in a DHCP environment ?
a. option 33
b. option 67
c. option 13
d. option 66
3
which condition prevents the establishment of a DMPVN tunnel between two spokes ?
a. HSRP is enabled on the spoke devices
b. IPsec is enabled on the spoke devices
c. the two spokes are behind different PAT devices
d. the two spokes have different tunnel keepalive settings.

@rnfl….Answer to Q9 is F (depends on the syntax)….in Kikavich, its correctly written as below:

9. Which command do you enter to filter only routing updates that are sent through interface
GigabitEthernet0/0?
A. R1(config-if)#passive-interface GigabitEthernet0/0.
B. R1(config-router)#no passive-interface GigabitEthernet0/0
C. R1(config-router)#passive-interface GigabitEthernet0/0
D. R1(config-router)passive-interface default
E. R1(config-if)#passive-interface default
F. R1(config-router)#distribute-list 1 out GigabitEthernet0/0

so the correct answer is F, not C in above case!

Guys couple of questions which im not really sure about, if someone can help, it would be much appreciated :)

1) Router# show ntp associations
Address ref clock st when poll reach delay offset display
~172.31.32.2 172.31.32.1 5 29 1024 377 4.2 -8.59 1.6
+~192.168.13.33 192.168.1.111 4 69 128 377 4.1 3.48 2.3 *~192.168.13.57 192.168.1.111 3 32 128 377 7.9 11.18 3.6
* Master (synced), # master (unsynced), + selected, ­ candidate, ~ configured
Which of the following is true?
A) Master is syncing and exchanging NTP packets successfully
B) Master is not syncing but exchanging NTP packets successfully
C) Master is not syncing and not exchanging NTP packets
D) All NTP packets are dropped

2) Which next hop is going to be used for 172.17.1.0/24 ?

Router(config-if)#do show ip bgp
BGP table version is 4, local router ID is 156.12.1.6
Status codes: s suppressed, d damped, h history, * valid, > best, i ­ internal, r RIB-failure, S Stale Origin codes: i ­ IGP, e ­ EGP, ? ­ incomplete
Network Next Hop Metric LocPrf Weight Path
*>i 10.1.1.0/24 192.168.1.2 0 0 10000 i
*>i 10.2.2.0/24 192.168.3.2 0 0 10000 i
*>i 172.17.1.0/24 10.0.0.1 0 0 32768 i
*i 10.0.0.2 0 0 32768 i
A) 10.0.0.1
B) 192.168.1.2
C) 10.0.0.2
D) 192.168.3.2

3) If you run the command auto-cost reference-bandwidth 10000 on one of the router in the network, what will happen?
A) It will make 10Gbps on all of them
B) it will make 1 Gbps on all of them
C) It will make 10Gbps on this router only
D) it will remain the same on all links of the router

4) What are two rules for compacting IPV6 address? (Choose two)
A) every 16-bits segment that consists of all zeroes can be represent with a single 0
B) the trailling zeores in any 16-bit segment do not have to be written
C) the leading zeroes in any 16-bit segment do no have to be written
D) any single, continuous string of one or more 16-bits segment that consists of all zeroes can be represent with a double ::
E) the maximum number of time a double colon can replace a 16-bit segment that consists of all zeroes is two
F) two zeroes in the middle of any 16-bit segment do not have to be written

5) You are configuring a Microsoft client to call a PPP server using CHAP. Only the client will be authenticated, but the client’s password has expired and must be changed. Which PPP server configuration allows the call to be completed?
A) ppp authentication chap callin
B) ppp authentication chap
C) ppp authentication ms-chap-v2
D) ppp authentication ms-chap-v2 callin
E) ppp authentication ms-chap callin

gys failed today
dumps are totally changed
no kavanchi
no dexture
no purchased

got 60 qs
labs were the same
dnd were a little bit same
over all questions are not from the dumps

@faouji what do you mean totally changed? Where did the questions come from then? Do you remember any of them?

@ all please give the correct answer
1
Which two tasks must you perform to configure a BGP peer group ?
a. Configure the soft-update value
b. Set the advertisement interval
c. Assign neighbours to the peer group
d. Activate each neighbour
e. Activate the default route
2
which DHCP option enable to permit static routes in a DHCP environment ?
a. option 33
b. option 67
c. option 13
d. option 66
3
which condition prevents the establishment of a DMPVN tunnel between two spokes ?
a. HSRP is enabled on the spoke devices
b. IPsec is enabled on the spoke devices
c. the two spokes are behind different PAT devices
d. the two spokes have different tunnel keepalive settings.

2
which DHCP option enable to permit static routes in a DHCP environment ?
a. option 33
b. option 67
c. option 13
d. option 66

ANSWER: A

Which two tasks must you perform to configure a BGP peer group ?
a. Configure the soft-update value
b. Set the advertisement interval
c. Assign neighbours to the peer group
d. Activate each neighbour
e. Activate the default route

ANSWER: C,D

@Anonymous and Denzel washington

where did ya’all find above questions pls

Hello all. what’s the answer for the following question? Is. “C” the answer for this question? can’t think of other options. thank you.

1. Which BGP option is required when load sharing over multiple equal-bandwidth parallel from a single CE router to a single ISP router over eBGP?
A. eBGP Multipath
B. eBGP Multihop
C. BGP Synchronization
D. Public AS numbers

silly me. Found the answer for this question. It is “A”
https://www.cisco.com/c/en/us/td/docs/ios/12_2sx/feature/guide/fsxeibmp.html

@Routeontheway mate they were in a vce. Most question are repeated but with different answers, if you know the right answers, pls help, cheers.

@Denzel Washington

My maaannn,

1) Router# show ntp associations
Address ref clock st when poll reach delay offset display
~172.31.32.2 172.31.32.1 5 29 1024 377 4.2 -8.59 1.6
+~192.168.13.33 192.168.1.111 4 69 128 377 4.1 3.48 2.3 *~192.168.13.57 192.168.1.111 3 32 128 377 7.9 11.18 3.6
* Master (synced), # master (unsynced), + selected, ­ candidate, ~ configured
Which of the following is true?
A) Master is syncing and exchanging NTP packets successfully
B) Master is not syncing but exchanging NTP packets successfully
C) Master is not syncing and not exchanging NTP packets
D) All NTP packets are dropped

answer A

2) Which next hop is going to be used for 172.17.1.0/24 ?
Router(config-if)#do show ip bgp
BGP table version is 4, local router ID is 156.12.1.6
Status codes: s suppressed, d damped, h history, * valid, > best, i ­ internal, r RIB-failure, S Stale Origin codes: i ­ IGP, e ­ EGP, ? ­ incomplete
Network Next Hop Metric LocPrf Weight Path
*>i 10.1.1.0/24 192.168.1.2 0 0 10000 i
*>i 10.2.2.0/24 192.168.3.2 0 0 10000 i
*>i 172.17.1.0/24 10.0.0.1 0 0 32768 i
*i 10.0.0.2 0 0 32768 i
A) 10.0.0.1
B) 192.168.1.2
C) 10.0.0.2
D) 192.168.3.2

answer A

3) If you run the command auto-cost reference-bandwidth 10000 on one of the router in the network, what will happen?
A) It will make 10Gbps on all of them
B) it will make 1 Gbps on all of them
C) It will make 10Gbps on this router only
D) it will remain the same on all links of the router

Answer C

4) What are two rules for compacting IPV6 address? (Choose two)
A) every 16-bits segment that consists of all zeroes can be represent with a single 0
B) the trailling zeores in any 16-bit segment do not have to be written
C) the leading zeroes in any 16-bit segment do no have to be written
D) any single, continuous string of one or more 16-bits segment that consists of all zeroes can be represent with a double ::
E) the maximum number of time a double colon can replace a 16-bit segment that consists of all zeroes is two
F) two zeroes in the middle of any 16-bit segment do not have to be written

Answer C,D

5) You are configuring a Microsoft client to call a PPP server using CHAP. Only the client will be authenticated, but the client’s password has expired and must be changed. Which PPP server configuration allows the call to be completed?
A) ppp authentication chap callin
B) ppp authentication chap
C) ppp authentication ms-chap-v2
D) ppp authentication ms-chap-v2 callin
E) ppp authentication ms-chap callin

answer C

Passed today with 84X. A lot of new questions.

i have the exam next week… pls help
1.which condition prevents the establishment of a DMPVN tunnel between two spokes ?
a. HSRP is enabled on the spoke devices
b. IPsec is enabled on the spoke devices
c. the two spokes are behind different PAT devices
d. the two spokes have different tunnel keepalive settings.
ANSW ?

2.When unicast reverse path forwarding is configured on an interface, which action does the interface take first
when it receives a packet?
A. it verifies that the source has a valid VEF adjacency.
B. It checks the egress access lists.
C. it verifies a reverse path via the FIB to the source.
D. It checks the ingress access lists.
Correct Answer: C OR D

@syn My Brudda, You’re The Real Man, Much Appreciated :)

thanks @denzel W.
@sandman….the correct is eBGP Multihop (imho)

@Routeontheway
if you don’t mind, would u please give us a bit of explanation? I’d like to get it done right. thank you in advance.

which condition prevents the establishment of a DMPVN tunnel between two spokes ?
a. HSRP is enabled on the spoke devices
b. IPsec is enabled on the spoke devices
c. the two spokes are behind different PAT devices
d. the two spokes have different tunnel keepalive settings.

D?

2.When unicast reverse path forwarding is configured on an interface, which action does the interface take first
when it receives a packet?
A. it verifies that the source has a valid VEF adjacency.
B. It checks the egress access lists.
C. it verifies a reverse path via the FIB to the source.
D. It checks the ingress access lists.

Ans:A

@Tep…yes D.

@sandman…i havent spent time on this particular one but someone given this as correct answer, few pages back.

Guys, I am thowing 76 question which I collected in last 10 days.

1. Which BGP option is required when load sharing over multiple equal-bandwidth parallel from a single CE router to a single ISP router over eBGP?
A. eBGP Multipath
B. eBGP Multihop
C. BGP Synchronization
D. Public AS numbers
Answer: A
2. which DHCP option enable to permit static routes in a DHCP environment ?
a. option 33
b. option 67
c. option 13
d. option 66
Answer A

3. which condition prevents the establishment of a DMPVN tunnel between two spokes ?
a. HSRP is enabled on the spoke devices
b. IPsec is enabled on the spoke devices
c. the two spokes are behind different PAT devices
d. the two spokes have different tunnel keepalive settings.

4. Refer to the exhibit. After configuring GRE between two routers running OSPF that are connected to each other via a WAN link, a network engineer notices that the two routers cannot establish the GRE tunnel to begin the exchange of routing updates. What is the reason for this?
A. Either a firewall between the two routers or an ACL on the router is blocking IP protocol number 47.
B. Either a firewall between the two routers or an ACL on the router is blocking UDP 57.
C. Either a firewall between the two routers or an ACL on the router is blocking TCP 47.
D. Either a firewall between the two routers or an ACL on the router is blocking IP protocol number 57.
Answer: A
5. Other than a working EIGRP configuration, which option must be the same on all routers for EIGRP authentication key role over to work correctly?
A. SMTP
B. SNMP
C. Password
D. Time
Answer: D
6. Which SNMP verification command shows the encryption and authentication protocols that are used in SNMPv3?
A. show snmp view
B. show snmp
C. show snmp user
D. show snmp group
Answer: C
7. What is EIGRP Summary Route Administrative Distance?
A. 90
B. 170
C. 5
D. 110
Answer: C
8. Refer to the following configuration command.
router(conttg)# ip nat inside source static tcp 172.16.10.8 8080 172.16.10.8 80
Which statement about the command is true?
A. Any packet that is received in the inside interface with a source IP port address of 1 72.16.10.8:80 is translated to 172.16.10.8 8:80
B. Any packet that is received in the inside interface with a source IP address of 172 16 10 8 is redirected to port 8080 or port 80
C. The router accepts only a TCP connection from port 8080 and port 80 on IP address 1 72 16 10 8
D. Any packet that is received in the inside interface with a source IP port address of 172 1 6 10 8 8080 is translated to 172.16.10.8 80
Answer: D
9. A Network engineer wants to configure logging to compile and send information to an external server. Which type of logging must be configured?
A. Terminal
B. Syslog
C. Buffer
D. Console
Answer: B
10. Which two OSPF router types can perform summarize in an OSPF network? (Choose two)
A. summary router
B. area border router
C. autonomous system boundary router
D. internal router
E. backbone router
Answer: B,C
11. In which two ways can split horizon issues be overcome in a Frame Relay network environment? (choose two.)
A. Configuring one physical serial interface with Frame Relay to various remote sites.
B. Configure a loopback interface with Frame Relay to various remote sites.
C. Configuring multiple subinterfaces on a single physical interface to various remote sites.
D. Enabling split horizon.
E. Disabling split horizon
Answer: C,E
12. Which two features does RADIUS combine? (choose two)
A. Telnet
B. Accouting
C. SSH
D. Authenticaiton
E. Authorization
Answer: D,E
13. During which DMVPN phase is spoke-to-spoke communication enabled?
A. Phase 1
B. Phase 6
C. Phase 5
D. Phase 2
E. Phase 4
Answer: D
14. Which three benefits does the Cisco Easy Virtual Network provide to an enterprise network? (Choose three.)
A. simplified Layer 3 network virtualization
B. improved shared services support
C. enhanced management, troubleshooting, and usability
D. reduced configuration and deployment time for dot1q trunking
E. increased network performance and throughput
F. decreased BGP neighbor configurations
Answer: A,B,C
15. Which three NTP operating modes must the trusted-Key command be configured on for authentication to operate properly? (Choose Three)
A. interface
B. client
C. peer
D. server
E. broadcast
Answer: B,D,E
16. Which two statements about Frame Relay LMI autosense are true on a Router? (Choose two)
A. It requires the LMI type to be explicitly configured.
B. It operates on Frame Relay DTE interfaces.
C. It operates on Frame Relay DCE interfaces.
D. It operates when the line is up by the line protocol is down.
E. It requires the line protocol to be up.
Answer: B,D
17. What is the primary service that is provided when you implement Cisco Easy Virtual Network?
A. It requires and enhances the use of VRF-Lite.
B. It reduces the need for common services separation.
C. It allows for traffic separation and improved network efficiency.
D. It introduces multi-VRF and label-prone network segmentation.
Answer: C
18. Which type of Netflow information is displayed when the show ip flow export command is executed?
A. local status and statistics
B. export interface configurations
C. sent status and statistics
D. top talkers
Answer: D
19. Question similar to this one:
17. What does the show ip route vrf CISCO command display?
A. directly connected routes for VRF CISCO.
B. the routing table for VRF CISCO.
C. the global routing table.
D. all routing tables that start with VRF CISCO.
E. the route distinguisher for VRF CISCO
20. Which access list entry checks for an ACK within a packet header?
A. access-list 49 permit ip any any eq 21 tcp-ack
B. access-list 49 permit tcp any any eq 21 tcp-ack
C. access-list 149 permit tcp any any eq 21 established
D. access-list 49 permit tcp any any eq 21 established
Answer: C
21. Same question but reversed:
Which two protocols can cause TCP starvation? (Choose two)
A. TFTP
B. SNMP
C.SMTP
D.HTTPs
E.FTP
Answer: A&B
22. Considering the IPv6 address independence requirements, which process do you avoid when you use NPTv6 for translation?
A. rewriting of higher layer information
B. checksum verification
C. ipv6 duplication and conservation
D. IPSEC AH header modification
Answer: A
23. RIPng question. Cannot receive updates. Why?
A. Firewall Port block UDP 520
B. Firewall Port block TCP 520
C. Firewall Port block UDP 521
D. Firewall Port block TCP 521
Answer: C
24. What is the default authentication in RIPv2 when authentication is enabled
A. SHA1 authentication
B. Enable password authentication
C. Plain text authentication
D. MD5 authentication
Answer: C
25. Which two tasks does a DHCP relay agent perform? (Choose two)
A. It forwards DHCPHELLO and DHCPREQUEST messages to the DHCP server
B. It forwards DCHPREQUEST and DHCPACK messages to the DHCP server
C. It forwards DHCPOFFER and DHCPCOMPLETE messages to the DHCP server
D. It forwards DHCPDISCOVER and DHCPREQUEST messages to the DHCP server
E. It forwards DHCPOFFER and DHCPACK messages to the DCHP server
Answer: D, E
26. Where must a network engineer configure the ip helper-address command on a router
a. On the interface that will receive the broadcasts
b. On the DHCP configuration
c. the interface that is closed to the destination DHCP server
d. on the global configuration mode
Answer : A
27. Which feature can be used to reduce the number of ICMP unreachable message egressing a router
a. uRPF
b. ICMP rate-limiting(upendra)
c. ip unreachables command
d. Asymmetric routing
Answer :B
28. What happens when a router receives a route with an administrative distance of 255
a. The router installs the route as the most preferred path in the routing table.
b. The router installs the route as the least preferred path in the routing table
c. The router becomes the feasible successor for the route
d. The router is unable to install the route into the routing table
Answer :D
29. A network access serve using TACACAS+ for AAA operations receives an error message from the TACACS+ server. which action does the network access server take next ?
a. It attempts to authenticate the user against RADIUS
b. It restarts and attempts to reconnect to the TACACS+ server
c. It rejects the user access request the
d. It checks the method list for an additional AAA option
Answer :C
30. which purpose of the AAA accounting feature is true when you use TACACS+ authentication ?
a. It prompts users to change their passwords when they expire
b. it saves a timestamped record of user activity
c. it controls the activities that the user is permitted to perform
d. it verifies the user identity.
Answer:B
31. Which command configure a default authentication list that uses a local database and a case-insensitive username ?
a. aaa authentication exec CONSOLE group local-case if authenticated
b. aaa authentication login CONSOLE group local
c. aaa authentication login default group local
d. aaa authentication exec default group local-case
Answer:C
32. Which two mask you perform to enable a point-to-point Frame Relay connection
a. Configure the encapsulation type
b. Disable inverse ARP
c. Enable inverse ARP
d. Configure static address mapping
Answer:A
33. If device R1 has 1-Gigabit and 10-Gigabit Ethernet interfaces, which command do you enter so that it takes full advantage of OSPF costs ?
a. R1(config-router)#auto-cost reference-bandwidth 10000
b. R1(config-router)#auto-cost reference-bandwidth 10000000000
c. R1(config-if)# ip ospf cost 10000000000
d. R1(config-if)# ip ospf cost 10000
e. R1(config-route-map)#set metric 10000
f. R1(config-route-map)#set metric 10000000000
Answer:A
34. In which two areas does OSPF send a summary route by default ?
a. NSSA
b. Backbone
c. Totally stubby
d. Stub
e. Normal
Answer :C&D
35. Which LAN feature enables a default gateway to inform its end devices when a better path to a destination is available ?
a. HSRP
b. ICMP unreachable messages
c. ICMP redirects
d. Proxy ARP
Answer :C

36. Which three methods can a network engineer use to fix a metric based routing loop in the network.
a. Implement offset lists at network boundaries
b. Filter routes manually using distribute lists
c. Filter routes manually using prefix lists
d. Implement proper network summarisation on key routing points
e. Filter routes based on tags
f. Utilise root database filters
37. Which two features ara added in MSCHAP Version 2
a. Backwards-compatibility with MSCHAP version 1
b. Using the MD5 hash for stronger security
c. Ability to change an expired password
d. using 3 way handshakes for authentication
e. mutual authentication between peers
38. What does the following access list, which is applied on the external interface FastEthernet 1/0 of the perimeter router accomplish.
# access-list 101 deny ip 10.0.0.0 0.255.255.255.255 any log
# access-list 101 deny ip 192.168.0.0 0.0.255.255 any log
# access-list 101 deny ip 172.16.0.0 0.15.255.255 any log
# access-list 101 permit ip any any
#interface fastEthernet 1/10
#ip access-group 101 in
a. It filter incoming traffic from private address in order to prevent spoofing and logs any intrusion attempts
b. It prevents private internal address to be accessed directly from outside
c. It filters incoming traffic from private address ranges 10.0.0.0-10.0.0.255, 172.16.0.0-172.31.255.255, 192.168.0.0-192.168.255.255 and logs any intrusion attempts
d. It prevents the internal network from being used in spoofed denial of service attacks and logs any exit to the internet
39. What is the default authentication in RIPv2 when authentication is enabled
a. SHA1 authentication
b. Enable password authentication
c. Plaintext authentication
d. MD5 authentication
40. Which command sequence can you enter on a router to configure Unicast Reverse Path Forwarding in loose mode
a. Interface GigabitEthernet0/0
Ip verify unicast source reachable-via any
b. Interface GigabitEthernet0/0
Ip verify unicast source reachable-via loose
c. Interface GigabitEthernet0/0
Ip verify unicast source reachable-via all
d. Interface GigabitEthernet0/0
Ip verify unicast source reachable-via rx
41. What is a function of NPTv6?
A. It interferes with encryption of the full IP payload.
B. It maintains a per-node state.
C. It is checksum-neutral.
D. It rewrites transport layer headers.
Correct Answer: C
42. An engineer executes the ip flow ingress command in interface configuration mode. What is the result of this action?
A. It enables the collection of IP flow samples arriving to the interface.
B. It enables the collection of IP flow samples leaving the interface.
C. It enables IP flow while disabling IP CEF on the interface.
D. It enables IP flow collection on the physical interface and its subinterfaces.
Correct Answer: A
43. Refer to the exhibit. After configuring GRE between two routers running OSPF that are connected to each other via a WAN link, a network engineer notices that the two routers cannot establish the GRE tunnel to begin the exchange of routing updates. What is the reason for this?
A. Either a firewall between the two routers or an ACL on the router is blocking IP protocol number 47. B. Either a firewall between the two routers or an ACL on the router is blocking UDP 57.
C. Either a firewall between the two routers or an ACL on the router is blocking TCP 47.
D. Either a firewall between the two routers or an ACL on the router is blocking IP protocol number 57.
Correct Answer: A
44. What is the purpose of the route-target command?
A. It extends the IP address to identify which VRF instance it belongs to.
B. It enables multicast distribution for VRF-Lite setups to enhance IGP routing protocol capabilities.
C. It manages the import and export of routes between two or more VRF instances.
D. It enables multicast distribution for VRF-Lite setups to enhance EGP routing protocol capabilities.
Correct Answer: C
45. Refer to the following configuration command.
router(config)# ip nat inside source static tcp 172.16.10.8 8080 172.16.10.8 80
Which statement about the command is true?
A. Any packet that is received in the inside interface with a source IP port address of 172.16.10.8:80 is translated to 172.16.10.8 8:80
B. Any packet that is received in the inside interface with a source IP address of 172.16.10.8 is redirected to port 8080 or port 80
C. The router accepts only a TCP connection from port 8080 and port 80 on IP address 172.16.10.8
D. Any packet that is received in the inside interface with a source IP port address of 172.16.10.8 8080 is translated to 172.16.10.8 80
Correct Answer: D
46. Other than a working EIGRP configuration, which option must be the same on all routers for EIGRP authentication key role over to work correctly?
A. SMTP
B. SNMP
C. Passwords
D. Time
Correct Answer: D
47. In which two ways can split horizon issues be overcome in a Frame Relay network environment? (choose two)
A. Configuring one physical serial interface with Frame Relay to various remote sites.
B. Configure a loopback interface with Frame Relay to various remote sites.
C. Configuring multiple subinterfaces on a single physical interface to various remote sites.
D. Enabling split horizon. E. Disabling split horizon.
Correct Answer: CE
48. A network administrator notices that the BGP state drops and logs are generated for missing BGP hello keepalives. What is the potential problem?
A. Incorrect neighbor options
B. Hello timer mismatch
C. BGP path MTU enabled
D. MTU mismatch
Correct Answer: D
49. Which IP SLA operation can be used to measure round-trip delay for the full path and hop-by-hop round-trip delay on the network?
A. HTTP
B. ICMP path echo
C. TCP connect
D. ICMP echo
Correct Answer: B
50. In a point-to-multipoint Frame Relay topology, which two methods ensure that all routing updates are received by all EIGRP routers within the Frame Relay
network? (Choose Two)
A. Use statically defined EIGRP neighbors on the hub site.
B. Create separate address families.
C. Disable split horizon.
D. Use sub interfaces.
E. Disable EIGRP auto summary.
Correct Answer: CD
51. A network engineer applies the command ip tcp adjust-mss under interface configuration mode. What is the result?
A. The probability of SYN packet truncation is increased.
B. The UDP session is inversely affected.
C. The probability of dropped or segmented TCP packets is decreased.
D. The optimum MTU value for the interface is set.
Correct Answer: C
52. A network engineer recently deployed Easy Virtual Networking in the enterprise network. Which feature improves shared services support?
A. route replication
B. edge interfacing
C. tunnel feedback.
D. route distinguishers
Correct Answer: A
53. Refer to Exibit.
What is indicated by the show ip cef command for an address?
A. CEF is unable to get routing information for this route.
B. CEF cannot switch packet for this route and passes it to the next best switching method.
C. A valid entry and is pointed to hardware based forwarding.
D. CEF cannot switch packet for this route and drops it.
Correct Answer: B
54. multicast application must be accessible between sites, but not be accessible outside of the organisation. Based on the scoping requirements, the multicast group address for the application will be allocated out of which range ?
a. FF00::/16
b. FF08::/16
c. FF02::/16
d. FF0E::/16
Answer: B or C
55. Which routing protocol searches for a better route through other autonomous systems to achieve convergence ?
a. Link-state
b. Hybrid
c. Path vector
d. Distance vector
Answer: A
56. What are the two benefits of BGP peer groups
a. support groups of paths
b. A configuration change can be applied simultaneously to all peers in the peer group
c. optimize backdoor routes
d. updated via multicast
e. each neighbour in a peer group can have different inbound BGP Policies
f. they use soft updates to minimize bandwidth consumption
Answer: B or F
56. Which two tasks must you perform to configure a BGP peer group ?
a. Configure the soft-update value
b. Set the advertisement interval
c. Assign neighbours to the peer group
d. Activate each neighbour
e. Activate the default route
ANSWER: C,D
57. true statement about conditional debugging
a. limited to Ethernet, serial, and multilink interfaces
b. generates debug messages only for packets entering the router
c. limit the output to a specific interface
d. support only one condition at a time
Answer: C
58. VPN support for IPv4 and IPv6 address families. Which command enables a VRF that supports these requirements?
a. Router(config-vrf)#route-target 004:006
a. Router(config)#ip vrf CUSTOMER
a. Router(config)#vrf definition CUSTOMER
a. Router(config-vrf)#rd 004:006
Answer: A or C
59. what are the two correct statements about enable secret and enable password command
a. the enable password command has a strong encryption algorithm than enable secret
b. if both commands are missing from the global configuration, vty lines use the console password
c. the enable secret command is backwards compatible with more versions of IOS
d. the enable secret and enable password commands must be used together
e. the enable secret command overrides enable password
Answer: C,E
60. Which feature is supported with stateful NAT64 ?
a. IP multicast
b. NAT44 and NAT64 on the same interface
c. VRF
d. FTP and ICMP on an application layer gateway
Answer: D
61. which of the following situations results in a routing loop ?
a. when you have a single point of redistribution
b. when you use NAT translation on the edge of your network
c. when you implement contiguous IP routing blocks
d. when you implement noncontiguous IP routing blocks
e. when you have multiple points of redistribution
Answer: E
62. Which three methods can a network engineer use to fix a metric based routing loop in the network.
a. Implement offset lists at network boundaries
b. Filter routes manually using distribute lists
c. Filter routes manually using prefix lists
d. Implement proper network summarisation on key routing points
e. Filter routes based on tags
f. Utilise root database filters
Answer:BCE
63 .Which two features ara added in MSCHAP Version 2
a. Backwards-compatibility with MSCHAP version 1
b. Using the MD5 hash for stronger security
c. Ability to change an expired password
d. using 3 way handshakes for authentication
e. mutual authentication between peers
Correct: C,E
64 .What is the default authentication in RIPv2 when authentication is enabled
a. SHA1 authentication
b. Enable password authentication
c. Plaintext authentication
d. MD5 authentication
Correct: C
65 .Which command sequence can you enter on a router to configure Unicast Reverse Path Forwarding in loose mode
a. Interface GigabitEthernet0/0
Ip verify unicast source reachable-via any
b. Interface GigabitEthernet0/0
Ip verify unicast source reachable-via loose
c. Interface GigabitEthernet0/0
Ip verify unicast source reachable-via all
d. Interface GigabitEthernet0/0
Ip verify unicast source reachable-via rx
Correct A.
66. Where must a network engineer configure the ip helper-address command on a router
a. On the interface that will receive the broadcasts
b. On the DHCP configuration
c. the interface that is closed to the destination DHCP server
d. on the global configuration mode
67. Which feature can be used to reduce the number of ICMP unreachable message egressing a router
a. uRPF
b. ICMP rate-limiting(upendra)
c. ip unreachables command
d. Asymmetric routing
68.What happens when a router receives a route with an administrative distance of 255
a. The router installs the route as the most preferred path in the routing table.
b. The router installs the route as the least preferred path in the routing table
c. The router becomes the feasible successor for the route
d. The router is unable to install the route into the routing table
69. A network access serve using TACACAS+ for AAA operations receives an error message from the TACACS+ server. which action does the network access server take next ?
a. It attempts to authenticate the user against RADIUS
b. It restarts and attempts to reconnect to the TACACS+ server
c. It rejects the user access request the
d. It checks the method list for an additional AAA option
70. Qustion about RIP. Something like connection not established between 2 routers via RIPv2, why?
ACL/Firewall blocked TPC 520
ACL/Firewall blocked TCP 521
ACL/Firewall blocked UDP 521
ACL/Firewall blocked UDP 520 <– correct answer
71. which purpose of the AAA accounting feature is true when you use TACACS+ authentication ?
a. It prompts users to change their passwords when they expire
b. it saves a timestamped record of user activity
c. it controls the activities that the user is permitted to perform
d. it verifies the user identity.
Correct B.

72. Which command configure a default authentication list that uses a local database and a case-insensitive username ?
a. aaa authentication exec CONSOLE group local-case if authenticated
b. aaa authentication login CONSOLE group local
c. aaa authentication login default group local
d. aaa authentication exec default group local-case
Correct C

73. Which two tasks you perform to enable a point-to-point Frame Relay connection ?
a. Configure the encapsulation type
b. Disable inverse ARP
c. Enable inverse ARP
d. Configure static address mapping
Correct A.

74. If device R1 has 1-Gigabit and 10-Gigabit Ethernet interfaces, which command do you enter so that it takes full advantage of OSPF costs ?
a. R1(config-router)#auto-cost reference-bandwidth 10000
b. R1(config-router)#auto-cost reference-bandwidth 10000000000
c. R1(config-if)# ip ospf cost 10000000000
d. R1(config-if)# ip ospf cost 10000
e. R1(config-route-map)#set metric 10000
f. R1(config-route-map)#set metric 10000000000
Correct A.

75. In which two areas does OSPF send a summary route by default ?
a. NSSA
b. Backbone
c. Totally stubby
d. Stub
e. Normal
Correct C,D.

76. Which LAN feature enables a default gateway to inform its end devices when a better path to a destination is available ?
a. HSRP
b. ICMP unreachable messages
c. ICMP redirects
d. Proxy ARP
Correct C.

HELLO,
MY EXAM IS FOR TOMORROW, IS THAT TRUE THAT REVIEW TO CHANGE;
THANK YOU IN ADVANCE.

@syn how the test go buddy? let us know. hope you passed

@syn –> Please let me know how was the exam?

@mario
Hey man, can you personally send me your notes and materials(dumps) upon collecting all the new questions up till now to my email — > jabraham59@ yahoo.com.
I will be really grateful for your help, sir :)

Please guys where are all these new questions coming from? it is getting confusing by the day. Are these the new questions seen in the actual exam or it is just copy and paste from another dumps.

@Ghauri are you studying those questions you posted and all the dumps???

What page or where is the Kikavich q’s?

What page or where is the Kikavich q’s and others located?

@joey
the best dumps before the change were kikavich. But since exam changed I am following just the comments section of digital tut had to take the exam by now but since new questions came and we don’t have complete new questions available yet. So I am waiting. Yes many questions from above questions are coming in the exam as per comments.

@hopeful all the material that is available is what i have found on the forum and close friends that have taken the test. the list that was readded by syn should cover all the questions and more importantly, he has posted the famous CPP/MPP D&D that everyone was wondering about. I’ve also confirmed with my friend and he confirmed that it is what he encountered on his test.

@joey i would suggest downloading all that is available on the forum. the more material you can get the better. Questions will vary and better of prepping for all of them rather than just memorizing.

Paassed Today (960/1000)
My email below to get dumps (PDF + VCE)
leop9600 @ gmail . com
Thanks to GOD

@ Joe and @Bubbles just go back a few pages and you”ll get the link. Someone posted the link again some days AGAIN..

hello everyone i have exam next week and i need help with this question, i dont know if this the correct answer pls help..

1.Which three methods can a network engineer use to fix a metric based routing loop in the network.
a. Implement offset lists at network boundaries
b. Filter routes manually using distribute lists
c. Filter routes manually using prefix lists
d. Implement proper network summarisation on key routing points
e. Filter routes based on tags
f. Utilise root database filters

OR B,C,E ANSWER:A,C,E ???

2.A network access serve using TACACAS+ for AAA operations receives an error message from the TACACS+ server. which action does the network access server take next ?

a. It attempts to authenticate the user against RADIUS
b. It restarts and attempts to reconnect to the TACACS+ server
c. It rejects the user access request the
d. It checks the method list for an additional AAA option
ANSWER :D ?

3.Which type of Netflow information is displayed when the show ip flow export command is executed?

A. top talkers
B. local status and statistics
C. sent status and statistics
D. export interface configurations

Correct Ans: C OR B

4. Multicast application must be accessible between sites, but not be accessible outside of the organization. Based on the scoping requirements, the multicast group address for the application will be allocated out of which range?

a. FF00::/16
b. FF08::/16
c. FF02::/16
d. FF0E::/16
answer: b???

5.Which routing protocol searches for a better route through other autonomous systems
to achieve convergence ?
a. Link-state
b. Hybrid
c. Path vector
d. Distance vector
answ :A???

6. VPN support for IPv4 and IPv6 address families. Which command enables a VRF that supports these requirements?

a. Router(config-vrf)#route-target 004:006
B. Router(config)#ip vrf CUSTOMER
C. Router(config)#vrf definition CUSTOMER
D. Router(config-vrf)#rd 004:006

7. what are the two correct statements about enable secret and enable password command

a. the enable password command has a strong encryption algorithm than enable secret
b. if both commands are missing from the global configuration, vty lines use the console password
c. the enable secret command is backwards compatible with more versions of IOS
d. the enable secret and enable password commands must be used together
e. the enable secret command overrides enable password
ANS: C AND E???

8. When use NPTv6 for IPV6 to IPV6 Address translation? (Choose two)
A. stateful address translation
B. a limit of 32 1-to-1 translations
C. lack of overloading functionality
D. identify all interfaces NAT inside or outside
E. 1-to-1 prefix rewrite
F. mismatched prefix allocations

Correct Answer: CE????

9. What are two limitations when in use of NPTv6 for lPV6 vs lPV6 Address translation?
A. stateful address translation
B. a limit of 32 1-to-1 translations
C. lack of overloading functionality
D. identify all interfaces NAT inside or outside
E. 1-to-1 prefix rewrite
F. mismatched prefix allocations
Correct Answer: CF
???

10.Which two tasks must you perform to configure a BGP peer group ?
a. Configure the soft-update value
b. Set the advertisement interval
c. Assign neighbours to the peer group
d. Activate each neighbour
e. Activate the default route

ANSWER: C,D???

11. Which BGP option is required when load sharing over multiple equal-bandwidth parallel from a single CE router to a single ISP router over eBGP?
A. eBGP Multipath
B. eBGP Multihop
C. BGP Synchronization
D. Public AS numbers

answ : B??

@Curious

I have no idea where they are coming from. But i promise you these are in the new exams as i failed last week. I didn’t see these questions anywhere during my revision but guys be vigilant and revise carefully.

@Abdul sorry about your exams. Thank you so much for clarifying. Just wanted some clarification from anyone who had taken the exams. Thank you. Good luck when you take the exam again as i am sure you do really good. Thanks again for your help.

here goes another one:

What is the international standard for transmitting data over a cable system?
A. PPPoE
B. DOCSIS
C. CMTS
D. AAL5

Answer: B

@Mario, bro you are on fire…thanks for your contributions with the questions. Good luck in your exam

Which BGP option is required when load sharing over multiple equal-bandwidth parallel links from a single CE router to a single ISP router over eBGP? Select the best response
A. eBGP Multipath
B. eBGP Multihop
C. BGP Synchronization
D. Public AS numbers

Answer: B

Which IP SLA operation requires Cisco endpoints?
A. UDP jitter for VoIP
B. ICMP Path Echo
C. ICMP Echo
D. UDP Jitter

Answer: A

Going to sit my exam in a couple of hours fingers crossed I don’t have too many Q’s out of left field. Will let you know how it was.

@Bunns Good luck in your exam and please keep us posted.

There are so many new questions , i just wanted to find out if it is mandatory to save all your configurations with copy run in the real exams before going to the next and what should you do if you can’t save it. Thanks

Sims:

Copy run start is DISABLED and not necessary
Show run works for most
Double check all IP don’t just memorize

1. Which DHCP option provides a TFTP server that Cisco phones can use to download a configuration?
A. DHCP Option 66
B. DHCP Option 68
C. DHCP Option 82
D. DHCP Option 57

Correct Answer: A

2. ALWAYS block the outbound web traffic on Saturdays and Sunday between 1:00 to 23:59
A. periodic Saturday Sunday 01:00 to 23:59 and IN
B. periodic Saturday Sunday 01:00 to 23:59 and OUT
C. periodic Saturday Sunday 01:00 to 11:59 and IN
D. Absolute Saturday Sunday 01:00 to 11:59 and IN

Correct Answer: B

3. Refer to following:
router eigrp 1
redistribute ospf 1 route-map ospf-to-eigrp
default-metric 20000 2000 255 1 1500
!
route-map ospf-to-eigrp deny 10
match tag 6
match route-type external type-2
!
route-map ospf-to-eigrp permit 20
match ip address prefix-list pfx
set metric 40000 1000 255 1 1500
!
route-map ospf-to-eigrp permit 30
set tag 8

Which three statements accurately describe the result of applying the exhibited route map?
A. The map prohibits the redistribution of all type 2 external OSPF routes with tag 6 set.
B. The map prohibits the redistribution of all type 2 external OSPF routes.
C. The map redistributes into EIGRP all routes that match the pfx prefix list and the five metric values 40000, 1000, 255, 1, and 1500.
D. The map prohibits the redistribution of all external OSPF routes with tag 6 set.
E. All routes that do no match clauses 10 and 20 of the route map are redistributed with their tags set to 8.
F. The map permits the redistribution of all type 1 external OSPF routes.

Correct Answer: AEF

4. Which command prevents routers from sending routing updates through a router interface?
A. default–metric
B. distribute-list in
C. passive-interface
D. distribute-list out

Correct Answer: C

5. When OSPF is forming an adjacency, in which state, the actual exchange of information in the link ?
A. INIT
B. loading
C. exstart
D. exchange

Correct Answer: B

6. Which NAT Command to disable dynamic ARP learning on an interface?
A. R(config-if)# ip nat enable
B. R(config-if)# ip nat inside
C. R(config-if)# ip nat outside
D. R(config)# ip nat service
E. R(config)# ip nat allow static host

Correct Answer: E

7. Which two commands must you configure on a DMVPN hub to enable phase 3? (Choose two)
A. ip nhrp interest
B. ip nhrp redirect
C. ip nhrp shortcut
D. ip network-id
E. ip nhrp map
F. ip redirects

Correct Answer: BC

8. Which two types of threshold can you configure for tracking objects? (Choose Two)
A. percentage
B. MTU
C. bandwidth
D. weight
E. delay
F. administrative distance

Correct Answer: AD

9. In which scenario can asymmetric routing occur?
A. active/active firewall setup
B. single path in and out of the network.
C. active/standby firewall setup
D. redundant routers running VRRP

Correct Answer: D

10. Which three NTP operating modes must the trusted-Key command be configured on for authentication to operate properly? (Choose Three)
A. interface
B. client
C. peer
D. server
E. broadcast

Correct Answer: BCE