Share your ROUTE v2.0 Experience

There was also a question about privledge level and it listed 0, 1, 15 and 16 and asked about what level do you need to give to a user so they can view the config but not access enable mode. Something like that

today passed with 82X. same drag drop 4 numbers and same labs 3 numbers. still getting around 15 new questions mentioned here.

1. multicast application must be accessible between sites, but not be accessible outside of the organisation. Based on the scoping requirements, the multicast group address for the application will be allocated out of which range ?
a. FF00::/16
b. FF08::/16
c. FF02::/16
d. FF0E::/16

2. Which routing protocol searches for a better route through other autonomous systems to achieve convergence ?
a. Link-state
b. Hybrid
c. Path vector
d. Distance vector

3. What are the two benefits of BGP peer groups
a. support groups of paths
b. A configuration change can be applied simultaneously to all peers in the peer group
c. optimize backdoor routes
d. updated via multicast
e. each neighbour in a peer group can have different inbound BGP Policies
f. they use soft updates to minimize bandwidth consumption

4. true statement about conditional debugging
a. limited to Ethernet, serial, and multilink interfaces
b. generates debug messages only for packets entering the router
c. limit the output to a specific interface
d. support only one condition at a time

5. VPN support for IPv4 and IPv6 address families. Which command enables a VRF that supports these requirements?
a. Router(config-vrf)#route-target 004:006
a. Router(config)#ip vrf CUSTOMER
a. Router(config)#vrf definition CUSTOMER
a. Router(config-vrf)#rd 004:006

6. what are the two correct statements about enable secret and enable password command
a. the enable password command has a strong encryption algorithm than enable secret
b. if both commands are missing from the global configuration, vty lines use the console password
c. the enable secret command is backwards compatible with more versions of IOS
d. the enable secret and enable password commands must be used together
e. the enable secret command overrides enable password

7. Which feature is supported with stateful NAT64 ?
a. IP multicast
b. NAT44 and NAT64 on the same interface
c. VRF
d. FTP and ICMP on an application layer gateway

8. which of the following situations results in a routing loop ?
a. when you have a single point of redistribution
b. when you use NAT translation on the edge of your network
c. when you implement contiguous IP routing blocks
d. when you implement noncontiguous IP routing blocks
e. when you have multiple points of redistribution

@xyz all of those questions you just added came on the test per my friend. Thx

@xyz
what were your answers to all above 8 questions ?

@Routeontheway
1.c
2.a
3.f,?
4.c
5.a
6.c,e
7.d
8.?

@xyz do you happen to know if the questions posted did appear on your test? Are there any other questions you can remember? Thx

@ Mario
did your friend pass the route exam

@ Mario
yes. few questions appeared in my test. I am trying to remember other questions.

@xyz yes he did not high score but yes

thnx @xyz

8. E (imho)

can someone please be kind enough to say whats MPP CPP ? drag n drop
and if possible share the MPP CPP dnd here pls…

Study group T e le g r a m:

t.me/joinchat/AGG6V0IkxiF55R1IQthg1w

I have exam Friday
i need to dump valid
please share to me
thanks advanced

@XYZ I think the correct answers are
1b
2 ?
3 b
4 c
5c
6 e ?
7 d
8 e
8

i need help with this qoues..

1Which command do you enter to filter only routing updates that are sent through interface GigabitEthernet0/0?
A. R1(config-if)#passive-interface GigabitEthernet0/0.
B. R1(config-router)#no passive-interface GigabitEthernet0/0
C. R1(config-router)#passive-interface GigabitEthernet0/0
D. R1(config-router)passive-interface default
E. R1(config-if)#passive-interface default
F. R1(config-router)#distribute-list 1 GigabitEthernet0/0 out

Answer: C OR F

2multicast application must be accessible between sites, but not be accessible outside of the organisation. Based on the scoping requirements, the multicast group address for the application will be allocated out of which range ?

a. FF00::/16
b. FF08::/16
c. FF02::/16
d. FF0E::/16
answer:c or b

3Which routing protocol searches for a better route through other autonomous systems
to achieve convergence ?
a. Link-state
b. Hybrid
c. Path vector
d. Distance vector
answ :?

4.VPN support for IPv4 and IPv6 address families. Which command enables a VRF that supports these requirements?

a. Router(config-vrf)#route-target 004:006
B. Router(config)#ip vrf CUSTOMER
C. Router(config)#vrf definition CUSTOMER
D. Router(config-vrf)#rd 004:006
ANS A ot C

5.Which three methods can a network engineer use to fix a metric based routing loop in the network.

a. Implement offset lists at network boundaries
b. Filter routes manually using distribute lists
c. Filter routes manually using prefix lists
d. Implement proper network summarisation on key routing points
e. Filter routes based on tags
f. Utilise root database filters

ANS ?

7. Which feature is supported with stateful NAT64 ?
a. IP multicast
b. NAT44 and NAT64 on the same interface
c. VRF
d. FTP and ICMP on an application layer gateway

this document states that A,C & D are not supported:

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipaddr_nat/configuration/xe-3s/nat-xe-3s-book/iadnat-stateful-nat64.pdf

When use NPTv6 for IPV6 to IPV6 Address translation? (Choose two)
A. stateful address translation B. a limit of 32 1-to-1 translations
C. lack of overloading functionality
D. identify all interfaces NAT inside or outside
E. 1-to-1 prefix rewrite
F. mismatched prefix allocations

Correct Answer: CE or CF
What are two limitations when in use of NPTv6 for lPV6 vs lPV6 Address translation?
A. stateful address translation
B. a limit of 32 1-to-1 translations
C. lack of overloading functionality
D. identify all interfaces NAT inside or outside
E. 1-to-1 prefix rewrite
F. mismatched prefix allocations
Correct Answer: CF OR CE ??

@MARIO

7. Which feature is supported with stateful NAT64 ?
a. IP multicast
b. NAT44 and NAT64 on the same interface
c. VRF
d. FTP and ICMP on an application layer gateway

this question is wrong
1.IP Multicast is not supported.
2.Application-level gateways (ALGs) FTP and ICMP are not supported.
3.Virtual routing and forwarding (VRF)-aware NAT64 is not supported.
4.Both NAT44 (static, dynamic andPAT) configuration and stateful NAT64 configuration are notsupported on the same interface

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipaddr_nat/configuration/xe-3s/nat-xe-3s-book/iadnat-stateful-nat64.pdf

Judging from the statements of previous test takers and scouring other guides here are some potential questions we may encounter.

QUESTION 564

Which two tasks does a DHCP relay agent perform? (Choose two.)
A. It forwards DHCPHELLO and DHCPREQUEST messages to the DHCP server.
B. It forwards DHCPREQUEST and DHCPACK messages to the DHCP server.
C. It forwards DHCPOFFER and DHCPCOMPLETE messages to the DHCP client.
D. It forwards DHCPDISCOVER and DHCPREQUEST messages to the DHCP server. E. It forwards DHCPOFFER and DHCPACK messages to the DHCP client.

Correct Answer: DE

QUESTION 563
You are configuring a Microsoft client to call a PPP server using CHAP. Only the client will be authenticated, but the client’s password has expired and must be changed. Which PPP server configuration allows the call to be completed?
A. ppp authentication chap callin
B. ppp authentication chap
C. ppp authentication ms-chap-v2
D. ppp authentication ms-chap-v2 callin E. ppp authentication ms-chap callin

Correct Answer: C

What is true about peer groups? (Choose Two)
A. Optimize backdoor routes
B. If you change configuration then it effects all peers in the group
C. Peer groups can send soft updates to all
D. Updates can be sent with multicast

Correct Answer: BC

What from the following can cause an issue for uRPF?
A. Asymetric routing
B. CEF not enabled
C. uRPF not applied to the traffic source
D. if it is used as ingress filtering

Correct Answer: A

Which three functionalities are specific to stateful NAT64? (Choose three)

A. 1:N traslation
B. It requires IPv4-transalable IPv6 address1
C. It helps ensure end-to-end address transparency and scalability
D. A state or bindings are created on every unique translation E. It conserves IPv4 addresses

Correct Answer: ADE

What is show on logging console 7?

A. Debugging and all above level
B. Information and all above level
C. Error and all above level
D. Emergencies and all above level

Correct Answer: A

One long question something like router get IPv6 information from ISP. Now it have to distribute name server and other options to hosts (how do routers distribute prefixes obtained from ISPs using DHCPv6)?

A. PPPv6
B. DHCP
C. Stateful Natv6
D. NPTv6
E. IPv4

Correct Answer: C

Question about IP SLA deployment cycle. Chose best IP SLA deployment cycle that reduce deployment.(Choose Four)

A. baseline (network performance)
B. understand (network performance baseline)
C. Understand Quality results
D. quantify (results)
E. fine tune and optimize
F. Update Understanding

Correct Answer: ABDE

Which type of Netflow information is displayed when the show ip flow export command is executed?

A. sent status and statistics
B. top talkers
C. export interface configurations
D. local status and statistics

Correct Answer: D

Which two options can you use to configure an EIGRP stub router? (Choose two)

A. summary-only
B. receive-only
C. external
D. summary
E. totally-stubby
F. not-so-stubby

Correct Answer: BD

Refer to the Exhibit.

configure terminal ip flow-export destination 192.168.10.1 9991 ip flow-export version 9
How can you configure a second export destination for IP address 192.168.10.1?

A. Specify a different TCP Port
B. Specify a different UDP port.
C. Specify a VRF
D. Configure a version 5 flow-export to the same destination
E. Specify a different flow ID

Correct Answer: B

I’ve seen other guides with answer C specify a VRF but I looked it up and Cisco documentation lists add a different UDP port to the address.

https://www.cisco.com/c/en/us/td/docs/ios/12_0s/feature/guide/12s_mdnf.html#wp1015363

Which two features does RADIUS combine? (Choose Two)

A. Telnet
B. Accouting
C. SSH
D. Authenticaiton
E. Authorization

Correct Answer: DE

Which two statements about EVN are true? (Choose two)

A. VRF using MPLS require a trunk interface that use EVN
B. VRF-Lite requires a trunk interface that uses EVN
C. All EVNs within a trunk interface can share the same IP infrastructure
D. Each EVN within a trunk interface must be configured separately
E. Commands that are specified once under a trunk interface can be inherited by all ENVs

Correct Answer: CE

Which two protocols can be affected by MPP? (Choose two)

A. POP
B. SMTP
C. HTTP
D. SFTP
E. SSH

Correct Answer: CE

If anyone has questions for MPP and CoPP please post them.

@Student

The answers for both are C & E.

With NPT there is no overloading functionality so all translations will be 1 to 1.

@syn I was about to ask if you took the test as you mentioned that yesterday. Let me know how it goes i’m taking it on Friday. Thx

@Mario

I was going to push it a day but I will man up and take it tomorrow.

1Which command do you enter to filter only routing updates that are sent through interface GigabitEthernet0/0?
A. R1(config-if)#passive-interface GigabitEthernet0/0.
B. R1(config-router)#no passive-interface GigabitEthernet0/0
C. R1(config-router)#passive-interface GigabitEthernet0/0
D. R1(config-router)passive-interface default
E. R1(config-if)#passive-interface default
F. R1(config-router)#distribute-list 1 GigabitEthernet0/0 out

Answer: C OR F

2multicast application must be accessible between sites, but not be accessible outside of the organisation. Based on the scoping requirements, the multicast group address for the application will be allocated out of which range ?

a. FF00::/16
b. FF08::/16
c. FF02::/16
d. FF0E::/16
answer:c or b

3Which routing protocol searches for a better route through other autonomous systems
to achieve convergence ?
a. Link-state
b. Hybrid
c. Path vector
d. Distance vector
answ :?

4.VPN support for IPv4 and IPv6 address families. Which command enables a VRF that supports these requirements?

a. Router(config-vrf)#route-target 004:006
B. Router(config)#ip vrf CUSTOMER
C. Router(config)#vrf definition CUSTOMER
D. Router(config-vrf)#rd 004:006
ANS A ot C

5. Which three methods can a network engineer use to fix a metric based routing loop in the network.

a. Implement offset lists at network boundaries
b. Filter routes manually using distribute lists
c. Filter routes manually using prefix lists
d. Implement proper network summarisation on key routing points
e. Filter routes based on tags
f. Utilise root database filters

ANS ?

When use NPTv6 for IPV6 to IPV6 Address translation? (Choose two)
A. stateful address translation B. a limit of 32 1-to-1 translations
C. lack of overloading functionality
D. identify all interfaces NAT inside or outside
E. 1-to-1 prefix rewrite
F. mismatched prefix allocations

Correct Answer: CE or CF
What are two limitations when in use of NPTv6 for lPV6 vs lPV6 Address translation?
A. stateful address translation
B. a limit of 32 1-to-1 translations
C. lack of overloading functionality
D. identify all interfaces NAT inside or outside
E. 1-to-1 prefix rewrite
F. mismatched prefix allocations
Correct Answer: CF OR CE ??

@Student:

1. C becuz passive filters updates thru interface
2. B becuz organization local address
3. A ?
4. C bcuz vrf definition use for multi protocol
5. C bcuz prefix list use to filter route redistribution

6. CF becuz It is a one for one prefix rewrite – you can’t overload it, have mismatching prefix allocations sizes, re-write ports or anything else. Importantly, it doesn’t
touch anything other than the prefix. Your network/host portion remains intact with no changes.

7. CF becuz see 6 above

@Stub

I failed last week. All the questions you just posted on previous page (148) was in the exam.

I’m planning on retaking next few weeks, can you help me find them answers.

@Stub told you those were the questions and the ones that xyz posted also were on the exam.

1. multicast application must be accessible between sites, but not be accessible outside of the organisation. Based on the scoping requirements, the multicast group address for the application will be allocated out of which range ?
a. FF00::/16
b. FF08::/16
c. FF02::/16
d. FF0E::/16

ANSWER: B

2. Which routing protocol searches for a better route through other autonomous systems to achieve convergence ?
a. Link-state
b. Hybrid
c. Path vector
d. Distance vector

ANSWER: A?

3. What are the two benefits of BGP peer groups
a. support groups of paths
b. A configuration change can be applied simultaneously to all peers in the peer group
c. optimize backdoor routes
d. updated via multicast
e. each neighbour in a peer group can have different inbound BGP Policies
f. they use soft updates to minimize bandwidth consumption

ANSWER: B, E –> https: //www. cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/13755-29.html

4. true statement about conditional debugging
a. limited to Ethernet, serial, and multilink interfaces
b. generates debug messages only for packets entering the router
c. limit the output to a specific interface
d. support only one condition at a time

ANSWER: C

5. VPN support for IPv4 and IPv6 address families. Which command enables a VRF that supports these requirements?
a. Router(config-vrf)#route-target 004:006
b. Router(config)#ip vrf CUSTOMER
c. Router(config)#vrf definition CUSTOMER
d. Router(config-vrf)#rd 004:006

ANSWER: C –> see last post https: // supportforums.cisco.com/t5/vpn/command-quot-ip-vrf-quot-vs-quot-vrf-quot/td-p/1431413

6. what are the two correct statements about enable secret and enable password command
a. the enable password command has a strong encryption algorithm than enable secret
b. if both commands are missing from the global configuration, vty lines use the console password
c. the enable secret command is backwards compatible with more versions of IOS
d. the enable secret and enable password commands must be used together
e. the enable secret command overrides enable password

ANSWER: C, E

7. Which feature is supported with stateful NAT64 ?
a. IP multicast
b. NAT44 and NAT64 on the same interface
c. VRF
d. FTP and ICMP on an application layer gateway

ANSWER: none are correct, probably bad question

8. which of the following situations results in a routing loop ?
a. when you have a single point of redistribution
b. when you use NAT translation on the edge of your network
c. when you implement contiguous IP routing blocks
d. when you implement noncontiguous IP routing blocks
e. when you have multiple points of redistribution

9. Which command do you enter to filter only routing updates that are sent through interface GigabitEthernet0/0?
A. R1(config-if)#passive-interface GigabitEthernet0/0.
B. R1(config-router)#no passive-interface GigabitEthernet0/0
C. R1(config-router)#passive-interface GigabitEthernet0/0
D. R1(config-router)passive-interface default
E. R1(config-if)#passive-interface default
F. R1(config-router)#distribute-list 1 GigabitEthernet0/0 out

Answer: C –> Since F is formatted incorrect

10. multicast application must be accessible between sites, but not be accessible outside of the organisation. Based on the scoping requirements, the multicast group address for the application will be allocated out of which range ?

a. FF00::/16
b. FF08::/16
c. FF02::/16
d. FF0E::/16

ANSWER: B (org local)

11. Which routing protocol searches for a better route through other autonomous systems
to achieve convergence ?
a. Link-state
b. Hybrid
c. Path vector
d. Distance vector

ANSWER: don’t know

12. Which three methods can a network engineer use to fix a metric based routing loop in the network.

a. Implement offset lists at network boundaries
b. Filter routes manually using distribute lists
c. Filter routes manually using prefix lists
d. Implement proper network summarisation on key routing points
e. Filter routes based on tags
f. Utilise root database filters

ANSWER: A, C, E

13. When use NPTv6 for IPV6 to IPV6 Address translation? (Choose two)

A. stateful address translation
B. a limit of 32 1-to-1 translations
C. lack of overloading functionality
D. identify all interfaces NAT inside or outside
E. 1-to-1 prefix rewrite
F. mismatched prefix allocations

ANSWER: C, E

14. What are two limitations when in use of NPTv6 for lPV6 vs lPV6 Address translation?
A. stateful address translation
B. a limit of 32 1-to-1 translations
C. lack of overloading functionality
D. identify all interfaces NAT inside or outside
E. 1-to-1 prefix rewrite
F. mismatched prefix allocations

ANSWER: C, E

8.
CORRECT ANSWER: E

Question 6, there was another similar to that. One that says about VTY line having a password not set if the enable secret would take over.

Question 7 did come out on the test with those choices.. you will see that on the test so be aware and use your judgement. No tester has aced any test never hehe.

@Mario

You are right, found this just now :

Caution If neither the enable password command nor the enable secret command is configured, and if there is a line password configured for the console, the console line password will serve as the enable password for all VTY (Telnet and Secure Shell [SSH]) sessions.

https: //www. cisco.com/c/en/us/td/docs/ios/12_2/security/command/reference/fsecur_r/srfpass.html

So to answer 6:

CORRECT ANSWER: B, E

Q7: VRF probably best answer then

I have exam Friday
i need to dump valid
please share to me
thanks advanced.

Question 7 for what I have read only support the following:

Only TCP and UDP Layer 4 protocols are supported for header translation.

So, since we already have verified all the choices within the question above, if there is another choice on the list, that would be the answer. It might be missing a layer 4 protocol on the list of choices. But, you will definitely see that question if you take the test this week.

@rnfl that is exactly the question I was referring to. Per my friend he got that question in the beginning of his exam.

Not sure where you got that question but, that is word for word from the test. Thx

@Mario @rnfl @Syn @Student

Is Jazzy 477, Kikvich questions dnd labs sufficient for 790 route?

@iseeip visit page 148 and you will get your answer. It’s a bit tiring to repost over again the same info.

2. Which routing protocol searches for a better route through other autonomous systems to achieve convergence ?
a. Link-state
b. Hybrid
c. Path vector
d. Distance vector

Why do we choose A

@Routeontheway

Here is the MPP CoPP DND:

CoPP:
+ Deals with protection against DOS attacks
+ Uses QoS
+ Assists with packet forwarding by decreasing the load on the control plane

MPP:
+ Uses one single command
+ Management traffic
+ One interface (or more) can be designated

@Anonymous

Actually answer is ‘C’ path vector since it is only EGP from list.

From white paper: Dynamic routes are learned by a routing protocol. Routing protocols can be classified into two categories: interior and exterior. Interior routing protocols learn about routes and route packets within an autonomous system (AS). Exterior routing protocols learn about routes and route packets between autonomous systems.

http:// www . ciscopress.com/articles/article.asp?p=99982

@Bowser

OSPF is link-state and can also route through different AS so C is not correct

Just a quick break from studying. What’s everyone’s next test? Are you doing Route first then all “down hill from there or did Switch then Route and looking forward to T-Shoot?

@syn for what I hear the route test is harder than switch. Tshoot is the easiest of all 3. I have another coleague that took switch last week and said that it was pretty easy and another that the written ccie is easier than the route, switch and tshoot. Go figure..

@Syn Switch will be next, then Tshoot, then CCIE Written

@ Mario,

Thank you for all your research. I can confirm what you have been finding is right on the money.

Just some info on Stateful NAT64:

1:N translation

Conserves IPv4 address

Uses address overloading, hence lacks in end-to-end address transparency

State or bindings are created on every unique translation

No requirement on the nature of IPv6 address assignment

Free to choose any mode of IPv6 address assignment viz. Manual, DHCPv6, SLAAC

I’ve already done Switch. To me the Labs were harder. Hopefully Route will be completed tomorrow and T-Shoot will be next.

Might go back and do CCNA Data Center. Might go CCIE written……who knows.

This is what I could find in regards to the VPN/VRP IPv4/IPv6 question:

Single-Protocol VRF to Multiprotocol VRF Migration
Prior to the introduction of the MPLS VPN VRF CLI for IPv4 and IPv6 VPNs feature, you could create a single-protocol IPv4-only virtual routing and forwarding (VRF) instance. You created a single-protocol VRF by entering the ip vrf command. To activate the single-protocol VRF on an interface, you entered the ip vrf forwarding (interface configuration) command.

After the introduction of the MPLS VPN VRF CLI for IPv4 and IPv6 VPNs feature, you create a multiprotocol VRF by entering the vrf definition command. To activate the multiprotocol VRF on an interface, you enter the vrf forwarding command.

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/mp_l3_vpns/configuration/xe-16/mp-l3-vpns-xe-16-book/mpls-vpn-vrf-cli-for-ipv4-and-ipv6-vpns.html

New questions Plz help me with the answers
1) A question about MSCHAP2 comparision with traditinal chap some options:
a) MSCHAP2 requires MD5 authentication (?),
b) MSCHAP2 maintained with three way handshake (definetly not, traditional CHAP also use 3way handshake)..,
c) MSCHAP2 can be maintained on time based password..

2) Which options mitigate layer 3 routing loop ( select three)..
a) something with network tag definiton,
b) offset definition
c)prefix-list configuration
d) distribute-list configuration
e) (I dont remember)
a,b,d but not sure..

Which two features ara added in MSCHAP Version 2
a. Backwards-compatibility with MSCHAP version 1
b. Using the MD5 hash for stronger security
c. Ability to change an expired password
d. using 3 way handshakes for authentication
e. mutual authentication between peers

i think A&E

Which two features ara added in MSCHAP Version 2
a. Backwards-compatibility with MSCHAP version 1
b. Using the MD5 hash for stronger security
c. Ability to change an expired password
d. using 3 way handshakes for authentication
e. mutual authentication between peers

should be C &E
https://www.cisco.com/c/en/us/td/docs/ios/12_2sb/12_2sba/feature/guide/sbaschap.html