Share your ROUTE v2.0 Experience

I could not post the reference link:

After assigning an EUI-64-designated IPv6 address to the interface, we can verify that the interface ID has been drawn from the MAC address in the process described for both the assigned and the link local address:

Router(config)# interface f0/0
Router(config-if)# ipv6 address 2001:db8::/64 eui-64
Router(config-if)# do show ipv6 interface f0/0
FastEthernet0/0 is up, line protocol is down
IPv6 is enabled, link-local address is FE80::212:7FFF:FEEB:6B40 [TEN]
No Virtual link-local address(es):
Global unicast address(es):
2001:DB8::212:7FFF:FEEB:6B40, subnet is 2001:DB8::/64 [EUI/TEN]

Hey vince did u you manage to compile a list of the corrections? I can create a new PDF for the 477Q

@Dan_2_One,

The file is protected, it will take you for ever to type it. A lot of the corrections are posted. I just chime in when a question is asked to try to help and prepare for the exam myself.

Ya i don’t mind creating a new one… but i cant look through all the forum to find the right answers. a lot fo the time people post and im not sure if its right

@Dan_2_One,

I would be in a better position next week after my exam. I understand.

Hi Vince can you tell me how to study?

thanks vince :)) good luck on your exam :))

@ Anus,

Start by reading the Official Cisco Guide for 300-101, then read How To Master CCNP-300-101.

practice labs using Boson Netsim.

Vince have u had a chance to check out the 515 ete file? are the questions correct? i mean, the questions are worded a bit weird

Hi Vince thank you. Where to find 300-101 Guide?

1 guys passed the CCIE R&S Written on 8th April.

If you want to learn more, pls check the below:

http://www.cciedc4labs.com/dump/ccie-rs.html

CCNP Routing And Switching Dumps

300-101 ROUTE
Last Updated: Apr 6, 2018
01-Choose：214

http://www.cciedc4labs.com/dump/route-switch-ccnp.html

Hi everyone, does anybody have cbtnuggets training series for the ROUTE exam? Thank you very much!

Hey guys,
i want to make a corrected 477q PDF and a VCE file. I can edit the PDF en can copy the text with an workaround through OCR for making the vce. I’ve been sniffing through this forum for the correct answers. It would been helping if someone can help me with which questions from the 477 file are incorrect so i can correct them in the PDF.

@Vince

Not sure yet a lot of content to get through.

Best of luck this week and you’ve been a credit to this forum.

Cheers

@mosh

cbtnuggets is not recommended, use INE lessons from Keith Bogart – more professional and in depth explanations.

@Prince

I thought about it too, i’m currently on 230Q, let me finish reading the questions ant then we’ll figure something out, deal?

@Vince

So can we agree that Q203 -> A and Q216 -> A,C?

Hi Guys, Started doing the 477 pdf, on question 170. Hanging in there ! I see lot of them complain about incorrect answers. Which section do them most question range ? So far I haven’t noticed anything. I got 5 questions mostly netflow related, one for revising. Got the exam tomorrow !

*I got 5 questions wrong mostly netflow related, one for revising.

@ Alex, Price – Did you find any wrong answers until what you have done (230q)? I’m using 477 version 30.0

@Dan_2_One,

I used the .ete for content since most questions have explanation. It is NOT more recent than the 477.

@Alex,

I have to check the wording again for Q203; dont see why cisco would put three distractors in one question.

I still believe Q216 is C,F.

I posed my reason earlier.

@Alex
Deal!

Q183 – Answer is marked A,C but I think the correct option is C,D

@Mark

It’s hard to say, many different opinions here, I mostly agree with corrections by @quetzal and @Khron from page 98, here’s what I come up with (excluding D&D, i didn’t review them and i think they shoulg go in the different file)

Q84 -> BCE

Q151 -> B

Q183 -> (not shure, do provide your opinion)

Q186 -> AC

Q187 -> AE

Q190 -> AD

Q203 -> A (not shure, do provide your opinion)

Q216 -> AC

Q220 -> BC

Q224 -> (not shure, do provide your opinion)

Q227 -> BE

Will update more when read through more Qs.

Kind discussion is welcome!

Q187 – Answer is marked A (solicit)C (request), it should be A (solicit) and E (reply)

Q151 – Answer is D
Q183 – Answer is C,D
I need to check on Q186

@Vince

F. DF bit clear means DF=0 which means – allow fragmentation if needed, and the Q is asking us of features that are preventing fragmentation (which in my knowledge is 3 – manual set of MSS, manual set of MTU and PMTUD(which is not recommended))

@Alex,

I agree with your answer, The DF Bit Clear will allow fragmentation. The keyword ‘prevent’ is the question is vital which I overlooked. I had to read the question again.

Chucks did mention it. Sorry about the confusion.

Q203, should the question be permit rather than block, no deny statement on ACLs. If so the correct answer is B
Time 1:00 23:59 (11:59 PM)
VLAN interface on the inside so ACL should be subject to incoming traffic (IN direction)

@Vince

Glad to hear that you’re on board, man!

And about the Q201, i’m really not sure either, but my guess is that if we need to block outbound web traffic on an interface – the only option is to use “out” argument in “ip access-group” command, and btw i agree that it’s not cisco-like to use this strange scheme where there’s one obvious correct answer that’s why i’m not 100% sure.

I meant Q203 in my previous post, sorry.

Passed yesterday with 840. Many questions in 477Q and dexter. Follow the forum for right answers!

out will be correct if the ACL was applied on the WAN interface. VLAN 303 is an interface on the host side so you would want to drop the traffic as it enters the router. Hope it makes sense.

@TY congrats,

Are you able to participate more in the forum? I know that you pass and are ready to more on but spare us just a few more comments. Thanks

Please forget about question 203, everything about the question is very wrong. I discovered that in the exam the questions are better written, its obvious the dumps were created from asking candidates what they had in the exam. That question is poorly written even the answers. Just understand what its about

All these questions with Drag and Drop are all incorrect.
see below Q 263,396,397 and 400 (all drag and drop)

Q234 D&D is wrong in Q477, I agree with correction by @quetzal on page 98.

Q216 – Is it not A and E ? E should have been PMTUD. TCP MSS will not totally avoid fragmentation if there is a lower MTU in the E2E path.

@Alex, agreed.

Q222 – It should be Option B – Serve-only

@Mark,

Q222 is A

https ://www.cisco.com/c/en/us/td/docs/routers/crs/software/crs_r4-3/system_management/command/reference/b_sysman_cr43crs/b_sysman_cr43crs_chapter_01011.pdf

When you disagree with a question please provide explanation. Thanks

My review of 477Q (Q230 through Q270)

Q234 (D&D) agree with correction by @quetzal on page 98

Q237 –> A

Q239 -> C

Q240 -> A

Q244 -> BCE (not shure, do provide your opinion)

Q247 -> E

Q255 -> D (not shure, the command needs to be applied in an interface level not in global config)

Q263 (D&D) agree with correction by @quetzal on page 98

Q265 (D&D) agree with correction by @quetzal on page 98

Q267 -> C

Will update more when read through more Qs.

Kind discussion is welcome!

Q222 is correct, I got it wrong. Q244 –> BDE

I’m on Q270. The corrections as you have stated are correct.
I’m aiming to complete the pdf in the next 3 hours. Then I have 7 hours to revise, 6 hours to sleep before tomorrow’s exam.

Thanks Alex and Vince !

Got passed yesterday with 8XX,

EIGRP STUB
OSPF SIM
EIGRP SIM

Questions From Digitaltut.

i’m studying from Dexture Dump i want to ask about the Sim 1 (OSPF Evaluation) and Sim 2 (EIGRP Evaluation) , these sims in dump only as explanation, i want to know what is the questions on it?

All the best Mark! May force be with you.

@ boxen,

Which section in particular? Many said that Digitaltut is not sufficient to pass.

can someone send me latest vce file please?
fightbacknt at gmail
Thanks