Share your ENCOR v1.1 Experience

Hello Anonymous,
Can you share the exact names of the labs? Are there many new questions in the exam?

Hello Ben,

Could you share the exact names of the labs? The labs I shared the names below were appeared in the exam? Also, how many new questions were in the exam?

LACP & Root Bridge Sim
VRF Configuration Sim 2
eBGP Neighbor Sim 2
OSPF Summarization Sim 2
NetFlow Sim 2

I test on Thursday, been studying these labs and questions six months, I tried to wait on new questions but I’m just like screw it at this point I’m ready to get it over with. network tut hasn’t failed me yet so I’m optimistic, I’ll let ya’ll know how it goes after Thursday and pay it forward as always.

Passed with 6 labs 58 MCQs
VRF Configuration Sim 2 (same as here)
LACP & Root Bridge Sim (same as here)
OSPF Summarization Sim 2 (same as here)
eBGP Neighbor Sim 2 (same as here, but L0, L1 and L2 all /32 advertised)
NetFlow Sim 1 (not Sim 2)
Access-list & CoPP Sim (same as here)

@Ben, @z
How many new questions?

New question?
While roaming between different model Wireless Lan Controllers clients get disconnected and connected again. What can be the reason?
– differnt virtuel interfac ips
– differnt mobility group name (correct?)
– same virtuel interfac ips
– ???

An engineer must configure flexible NetFlow on a router. There is a requirement to view IPv4 traffic QoS classification markings. The maximum information about the traffic flow should also be visible flowing through the network. Which flow record is suitable for the configuration?

A. flow record CCNA_NETFLOW
match ipv4 dscp
match ipv4 protocol
match ipv4 source address
match ipv4 destination address

B. flow record CCNA_NETFLOW
match ipv4 tos
match ipv4 protocol
match ipv4 source address
match ipv4 destination address

C. flow record CCNA_NETFLOW
match ipv4 tos
match ipv4 protocol
match ipv4 source address
match ipv4 destination address
match ipv4 source-port
match ipv4 destination-port

D. flow record CCNA_NETFLOW
match ipv4 dscp
match ipv4 protocol
match ipv4 source address
match ipv4 destination address
match ipv4 source-port
match ipv4 destination-port

Correct answer?

Hello, please update pages with new questions? Thanks.

Hello guys. Can you please share the latest dump with me at abdulhafizmatti2001atgmail.com?

I just took the test and passed. So I’ll pay it forward best I can

before I do, thanks again DigitalTUT for everything you do, your site has helped me with so many exams, not just studying questions but providing insight and theory to all the concepts. What a great resource keep it up.

ok, if you are waiting for new questions, you don’t have to, I had about 50ish questions, all from here maybe 10 new ones and I can’t remember what they were

all labs from here, I think six of them I had VRF1, ACL/COPP (ICMP), SLA, OSPF network statement and /17 summary, LACP and I can’t remember the other but they were all from here

what I used to study these is DEVNET sandbox on cisco, I created the yaml files myself according to what’s on this site and did the labs daily, I studied questions on here and also had a cisco U course and I used Kevin Wallace course too, studied about 9 months

all the questions were from here accept maybe 10ish, I guessed but I think I did well enough on the labs to get through any issues I had with questions, about 5 python questions, about 5 drag and drop

if you know the material and all the questions here on the site and the labs back and forth you will be fine. I’m a CCNP now (took ENARSI two years ago) THANKS DIGITAL TUT \m/

oh I remember the other lab NETFLOW 2, had to use the ip flow monitor command to for the preconfigured flow monitor

hope that helps, like I said all labs and questions from here accept maybe 10 questions

BGP2 lab was on it too, just remember V2 with the address-family pay attention to detail on the labs I had to advertise /32 loopback networks, and I misspoke, I had the VRF 2 lab on the test ,all I had access to was router 22, created tunnel interface, source destination, the VRF was already created fortunately. I had two static routes, and I verified by pinging from the switch to the other switch ip sourced from vlan 222 just like the lab here, so know it and you’ll be fine

Congratulations JMF!!!!!!!!!!!!!!!!!!!!!!!!!!!

Hello @JMF

Please, I would like to know if there are any new questions that are not included in the exam topics.

Also, are the lab questions the same as those in the exam topics?

I wait your reply
Thanks

there were new questions I hadn’t see before, about 10 but they were all exam topic questions, the labs were the same as on here other than maybe some different subnet numbers and masks

Hello @JMF

Please, I would like to know if there are any new questions that are not included in the exam topics.

Also, are the lab questions the same as those in the exam topics?

I wait your reply
Thanks

&digitaltut, is there a problem or something. It’s close to a month now and no updates from you guys.

Please don’t keep us in the dark. The more we wait the more new questions are being added.
If you won’t be providing them let us know please 🙏 so we can sort another option and do the exam once and for all please 🙏

Hi everyone, I passed the exam, don’t worry, there are maybe 5 new questions that I haven’t seen before, but they are simple (I don’t remember the content but there was one new D&D about ansible and puppet)

Labs are the same as here on the website with minor changes to the data.

VRF Configuration Sim 2 (same as here)
eBGP Neighbor Sim 2 ( same Lo0,Lo1,Lo2 advertsie)
Access-list & CoPP Sim (http get, frequency 600, police 1000)
NetFlow Sim ( flow export was already pre-configured here, only must add destination and protocol transport))
LACP & Root Bridge Sim (two interfaces to LACP, but be careful one port was shutdown)
OSPF Summarization Sim 2 (/18 summaraize, IP the same)

Thanks Digitaltut

Hi ! i will take the exam on 06.03, do you have any updates about new questions /Labs?
THX!!!

Hello @DNW

I want to knwo 5 new questions and new D&D about ansible and puppet are from exam topics ?

I wait your reply

Regards

enable

2. configure terminal

3. flow exporter exporter-name

4. description description

5. destination {hostname | ip-address} [vrf vrf-name]

6. export-protocol {netflow-v5 | netflow-v9 | ipfix}

7. transport udp udp-port

8. exit

9. flow monitor flow-monitor-name

10. exporter exporter-name

11. end

12. show flow exporter exporter-name

13. show running-config flow exporter exporter-name

@kossy

for me my exam last month of mars

@julia, Yes, question are from exam topics.

@DNW ,

Thanks for your reply

Please can you send dump exact that you are used

Thanks in advance

I took my exam a week ago and passed.
You have to read the tasks very, very carefully.
In NetFlow 2 SIM, flow exporter was preconfigured BUT the command export-protocol netflow netflow-v9 was missing. Very important!
With IP SLA icmp-echo I had to ping the Lo0 interface from SW1.
On SW1 when configuring SPAN I didn’t have to specify a VLAN as a source, but rather the interface e0/0. Just an example

A another example.
ACL_CoPP SIM. The protocol was OSPF, then it was to allow Telnet on R10. But I had to do the configuration on R30. After configuration I was able to test the Telnet from R20 to R30

In my exam there were 52 questions, 6-7 of which were completely new and 3-4 of which were slightly modified. The rest was from digitaltut.
One question was about PCAP file with 4way handshake, somethig needed to check. Options were: M1, M2, M3,M4 somthing like that
Reference: https://networklessons.com/wireless/wpa-and-wpa2-4-way-handshake
It was something about GTK. I believe the correct answer was either M3 or M4

Another question was about the GUI configuration of the WLC 9800. I can’t remember it, sorry
Pay attention! There are questions that look very similar, for example:
Which tag defines the roaming domain and properties of an AP deployment?
• A. AP tag
• B. policy tag
• C. site tag correct
• D. RF tag
AND/OR
Which tag defines the properties to be applied to each specific WLAN?
• A. RF tag
• B. site tagwrong
• C. policy tag correct
• D. AP tag
There were also Old ENCOR Questions from Q4-11

Big Thanks to Admin@digitaltut

Hello @anyonyme

Please about the LAB , are the same in examtopic ?

I wait your reply

Regards

Congratulations @Anonymous.

Could you share the exact names of the labs? The labs I shared the names below were appeared in the exam?

LACP & Root Bridge Sim
VRF Configuration Sim 2
eBGP Neighbor Sim 2
OSPF Summarization Sim 2
NetFlow Sim 2

@digitaltut,

Please give us a timeline for the questions so we can prepare accordingly.

Passed 6 labs 52 theory qsn. a few new qsn I can’t recall how many
LACP & Root Bridge Sim
VRF Configuration Sim 2
eBGP Neighbor Sim 2
OSPF Summarization Sim 2 /17
NetFlow Sim 2
Access-list & CoPP Sim

Passed exam this week. I had 6 labs + 52 or 54 questions. All labs are similar from site. Had 2 problems in Lab:
1. VRF – forgot to add vrf in static route and ping test didn’t work. And it was good to re-ccheck configs in router and switch. Noticed that switch didn’t have ip setting in vlan config. Added it + noticed vrf missing in static routes
2. Have got strange problem configuring OSPF using network… 4 networks for area 0 implemented well, but the similar command for network of area 40 didn’t work. Finally, exit from ospf config and re-entered there again and command accepted.
Lots of new questions for me at least. Probably, 10-15 questions that I have seen from the site. But seems weight of labs for scoring is very high, so finally passed exam. It looks like THOOT exam many years ago.
Many thnks @digitaltut for this site!
Good luck!

Hello Guys, I have been preparing ENCOR for past few weeks and ready to take it. Can anyone please suggest how we can get reading questions/labs from digital tut , is that subscription we need to signup for ?

Passed yesterday… 6 labs and 52 questions… 8-10 new question..
Labs
LACP and root bridge
OSPF without network command and /18 summary route
VRF finance sims
Copp_ACL
BGP with address family
Netflow sim was tricky one got 1 task from sim 1 and 2 from netflow sim2 and also task was not exactly same as this website… for 1st task flow monitor and flow exporter was already configured on ethernet 0 port without destination ip.. was asked to add destination ip in 1st task… 2nd task was to source from both PC and send to 3rd port… to source from both you need to add monitor session 1 source interface int1,int2 both cli and 3rd task was to do get http for one of the ip….
New questions i can not remember all but one was related to wireless regarding how fast locate locate the clients… options was data packets, beacon, rssi and can not recall 4th one… answer is data packets from clients…good luck everyone…

hi guys how can I fınd the questions? could you please help

I passed the exam. Thanks a lit Digitaltut! You saved me. I got a bit similar version as above AFN…

6 labs and 52 questions… 8-10 new question..
Labs:
LACP and root bridge
OSPF without network command and /18 summary route
VRF finance sims
Copp_ACL
BGP with address family
Netflow sim

There were around 15 questions from the “ ENCOR 350-401 v1.1” which were placed under so many different topics. So you must study those as well.
Less than 10 new questions. All others were in this site!

All the best guys!

An engineer is implementing a new SSID on a Cisco Catalyst 9800 Series WLC that must be broadcast on 6 GHz radios. Users will be required to use EAP-TLS to authenticate.
Which wireless Layer 2 security method is required?
A. WPA3 Enterprise
B. WPA3 Personal
C. WPA2 Enterprise
D. WPA2 Personal
Ans…….?

An engineer must configure a new WLAN that allows a user to enter a passphrase and provides forward secrecy as a security measure.
Which Layer 2 WLAN configuration is required on the Cisco WLC?
A. WPA2 Personal
B. WPA3 Enterprise
C. WPA3 Personal
D. WPA2 Enterprise
Ans……?

first one Ans : C (WPA3 Ent )
second one Ans : C (WPA3 Pers)

first one Ans is A : WPA3 Enterprise sorry

Passed the exam today. Thanks Digitaltut for your consistent efforts..! Hats-Off to your team.
I don’t know what the “NEW” questions are, as I don’t experience single question that does not exist here despite just some sequence and IP changes all stuff is covered here. Most Qs are from ENCORv1.1 and few from Part 4 – 11.

Exam Summary: [Total 58Qs and 6 Lablets]
NetFlow Sim 2 #be careful (exporter missing transport udp config, you cannot configure flexible Netflow-v9, show command displays v9 running already)
Access-list & CoPP Sim (ICMP)
OSPF Summarization Sim 2 (with /17 summary route)
eBGP Neighbor Sim 2 (All loopbacks were /32)
VRF Configuration Sim 1 (not Sim 2)(static routes from task-3 already exists)
LACP & Root Bridge Sim

Hello

@Hasnu

Please what is mean RF Configuration Sim 1 (not Sim 2)

what are the lab from SIM1 and LAB from SIM2

Thanks

Passed exam, dont panic for new questions, had couple of them i am not sure if selected them.
Focus on what we have here and is enough to pass

NetFlow Sim 2
Access-list & CoPP Sim (SSH)
OSPF Summarization Sim 2 (with /17 summary route)
eBGP Neighbor Sim 2
VRF Configuration Sim 1
LACP & Root Bridge Sim

@Power_over_ethernet
Please what is mean RF Configuration Sim 1 (not Sim 2)

what are the lab from SIM1 and LAB from SIM2

I wait your reply

Thanks

@julia
Under the Lab Sims, we have two VRF Sims as listed below. One of them is Sim 1:

=== Lab Sims for ENCOR v1.1 ===
VRF Configuration Sim —> This is VRF Configuration Sim 1
VRF Configuration Sim 2

Hello
@Hasnu

Sorry, I can’t find the exact link for the lab from SIM1 and the lab from SIM2.

Please, can you send me the exact link?

Thanks in advance

@julia
you should be Premium member to access the Sims. If you are already a Premium member just login, press “Ctrl+F” on your keyboard, copy ‘VRF Configuration Sim’ and search. Then the highlighted link on the right is the actual Sim you will be able to identify easily.

not , i ma not Premium member

so must purchase ?

Thanks

@julia
yes definitely, its a must purchase..!

are there new questions?

My exam is end MARS

so i hope pass and not diffcule