Share your ENCOR Experience

Passed today .
All questions from here.
SIMs:
– ospf no network
– bgp
– hsrp
– new sim : ensure 2 pcs connected via a port channel can ping each other .
Requirement was to configure one switch so that pcs can ping each other.
Basically you have to make sure the right interfaces and vlans are part of port channel.

Good luck everyone !

Is there a a master list with ALL the questions in one file?

Anyone encountered the new GRE sims? do you need route or just need vrf?

Passed yesterday…all question from here, maybe couple of new questions or old ones a little bit changed…
SIMs:
– ospf (no “network”);
– bgp (R1 and R3 config “allowas-in”);
– vrrp (“timers advertisements 15”);
– GRE and VRF (new one):
needed to distribute VRF through tunnel;
topology with two routers, ISP router and switches;
actually needed to configure “tunnel source” and “tunnel destination” to bring the tunnel UP;
and protect tunnel with already configured ipsec profile “My profile” (“tunnel protection IPsec profile );
Couple of D&D, also all form here.

Good luck to everyone!

protect tunnel with already configured ipsec profile “My profile” (“tunnel protection IPsec profile ) —>>> should be

protect tunnel with already configured ipsec profile “My profile”:
tunnel protection ipsec profile PROFILE_NAME

@djz

What do you mean to distribute VRF? So vrf “any name” is already configured and you just need to put it into GRE tunnel interface?
”
int tunnel1
vrf tunnel “VRF_Name”
tunnel source ip s2/0
tunnel destination “1.1.1.1”
tunnel protection ipsec profile PROFILE_Name
”

something like this? my test is on May 17th and i have no idea on GRE sim. hehe

@djz

is the command below for GRE?

”
int tunnel1
tunnel vrf “VRF_NAME”
tunnel source serial1/1
tunnel destination 1.1.1.1
tunnel protection ipsec profile MY_PROFILE”

Greetungs team

please keep us updated im writing the 19th friday.

I passed yesterday
Most of the questions from here (Premium)

I got a new lab (easy one)

connectivity issue
( you only have access to one switch)
1) you have to solve trunking issue between two switches to let the connected PCs ping each other
I configured the interface as trunk with the needed encapsulation then allowed the vlan on the trunk

2) issue with the port channel (LACP) with second switch ( I just configured 2 interfaces under port channel 1 mode active

3) they asked to let the switch use 32 bit for cost, I shown the doable commands and configured the below
spanning-tree pathcost method long

@ all recent test takers

digitut added new questions on 9th may. did you get any from the new questions

Hi! Can be used “?” or “TAB” on the exam in the simulators? thnx!

@Duck, @Didi

yes, that is the config…actually task said something like that “distribute VRF through tunnel”, but there is already VRF config on tunnel interface, so just needed to add “source” and “destination” in tunnel interface config to bring the tunnel UP

Just passed ENCOR and all questions are still valid, just one new SIM.
In the new sim, you have access to one switch and you need to resolve an issue with Trunk(just configure the interface as a trunk and allow only VLAN 600 and leave native default 1, fix channel-group 10 configuration to the second switch. and configure the access port for VLAN 600 to PC1.
Other SIMS were here: BGP allowas-in, VRRP SIM, and OSPF configuration.
Study the official guide and use this website as an extended resource, make sure you understand the concepts behind questions and you will be perfectly fine. Most of the questions were from parts 4 to 11 but as well have few from an older question pool so make sure you go through all of them.

Thank you Digitaltut!!! I pass today!

Where are the Questions? I don’t see any mentioned here.

Any idea on after how long cert is updated on cisco or pearson website after you pass the exam?

I got the result just after I finished the exam – said I passed . Few hours later I received the score report and 2 days later I got the email from Cisco confirming the certification status.
HTH.

Hi,

my premium membership expired on the 13th and my exam is scheduled on the 18th. just want to know if there is any update on the new questions or SIMs (last update was on the 9th)

Thank you

Hey Leda i do see new sims , im also writing on friday
I hope the premium covers this new labs, i think its two, but you will get one new and not two

so far there is 2 new sims on exam but not yet added here in premium

1. PC need to ping each other (related to vlan trunk config)
2. GRE tunnel with ipsec (ipsec is already configured and just need to apply on gre tunnel)

Hello! I passed today!
Sims:

– BGP Neighbor Sim
– OSPF Auth. with Diff. Area Sim
– SPAN & NetFlow Sim
– EEM Configuration Sim

Few new questions. The premium is valid! Thank You Digtaltut!

Goid luck for everyone!

Passed!

94 questions, with 3 labs included:-
– BGP allowas-in;
– SPAN&Netflow;
– GLBP;
– new OSPF.

Regarding new sim, there are 4-5 routers, one router is ABR (R2), has legs on all areas (area 10, 20, 0).

There are 2 request:
– to set on R2 for aria 10, to be always DR: i set on interface ‘ip ospf priority 255’. The router has one leg in aria 10, so is impossible to miss the interface.
– summarize R2 for aria 10, to announce only one route to other routers. I checked my interface in aria 10, was 10.1.10x.0/24, checked the other router in aria 10, had 10.1.10x.0, 10.1.20x.0, so I summarize on R2 under ospf: ‘area 10 range 10.1.0.0 255.255.0.0’.
Then I checked the other routers and there is only 10.1.0.0/16 received, only aria has have 10.1.x.x, the other aris are like 10.2.x.x, 10.3.x.x.

Questions were from 4-11, no new questions, iI think that 1-2 were from 1-3 part, and few D&D, but this is random.

That’s all, so go for Premium.

for the guys recently took the exam, can you confirm the total number of questions? 94 or 102 ? thanks

Hello Can any one help me please all i wanted to know about the Drag and Drop questions how many are there and which are they in the Exam

The 2 new sims (I encounter only new OSPF) are very easy, this should not be a problem for a CCNP or CCNA guy, you have the possiblity to verify, because are labs. The major issues could be with the questions but thanks to 9tut, is not a problem.
1st all, go to premium is mandatory.

@Hi, guys freefile.no-iaaaaap.fr Go and open linkk Dlit aaaa

Just pass the test i got 98% 48 multiple-choice questions All MCQ questions from this filee,

Passed
4 Sims
GLBP
SPAN and Netflow
BGP (R1 and R3 config “allowas-in”)
BGP ( new SIM)

All questions from Premium

@hunterskill23 : how many questions you got in total?

@hunterskil23 : the BGP (new sim) is the draft version?

passed yesterday
94 questions in total
4 sims (new one is about GRE)
Goodluck!

Has anyone taken the exam with a macOS laptop? there are no problems with this operating system?

@ ccnp_encor @STudent
BGP new sim is the Draft version
about 96 questions , didn’t have the time the finish them ( 2 left)
A tip : Do the composite quizz 100 Q about 10 times , I m sure you’ll be fine .

Please where can i find the questions for the answer.?

OK we have enough about the LAB right. NOW can any one answer about the DRAG and DROP Please Thanks all iwanted to know how many in the EXAM and what are they. you guys are talking about lab lab and lab understood. Thank you can anu one answer please about DRAG and DROP.

Thanks in Advance

Hello everyone! I passed today!

94 Questions.

4 Sims:
OSPF (Summarize network)
OSPF (Create neighbor)
BGP (R2, as-override)
EMM

Be careful with drag and drop.

All questions from Premium.

Good luck for everyone!

Please what are the DRAG and DROP questions are in the EXAM thank you. Enough about LABS.

@ccnp_encor_170523 OSPF sim are from premium or new one?

Hi guys, my ccnp cert is going to expired, may i ask which Concentration exam is considered easier to pass? Last time i used to just retake CCNP-Tshoot exam coz it’s easier but now it’s no longer possible.
Thanks.

@Nick Law :
the best way to be recertified your CCNP is to take the Encor Exam.

Hello everyone, I took the exam and passed.

All questions from Premium.

For 4 sim
HSRP
OSPF (new sim)
Log and netflow
Port channel and native vlan

OSPF (new sim)
-need to configure two routers no to participate DR/BDR election for area
-need to configure DR for one router in a area.

@digitaltut, From where can I find New OSPF and GRE sims on premium?

what are configs to do on new GRE sim?

How to configure new ospf sim mentioned above???

Hello every , I took the exams this morning and passed.

All question from premium

4 sims
2 OSPF
EEM
GRE
… Total of 94 questions

Hi
Will take ENSLD exam
Please help me
Any labs or only mc questions

Question if you miss one lab can you pass the exam.

@Nick Law To recertify with the Concentration exam, actually you have to pass two of them. So go for Encor exam.

I have the new 2 Sims for OSPF and VRF Tun0.
I sent to digit to solved.

Questions for those who have taken the exam….I have been reading that most of the questions come from part 4 to part 11. Is this correct? Do you recommend focusing and investing as much time in these.? (though avoidance of having a quick look at the other questions)