Share your ENCOR Experience

Passed .

anybody can share the lab for the exam?

Hola, There is a sim on the exam going over ospf c0nfig just heads up I get (96%)

Rmov ÷
lihbd.÷tk

me, Anonymous I am fake

anybody can share the lab for the exam?

I’v passed last week. There was a lab to configure GLBP on vlan 100. I had to configure one switch as AVG. After failure AVG must recover after minimum 15s.

Passed exam but there’s a lab/sim on bgp with same AS number which i probably flunked since it is uncommon bgp configuration

studied here and cbt nugget to prep for exam.

Hi Guys,
who took the exam recently?
Please share your experience .. Unfortunately we still don’t have any reliable information about LAB.

Where can I find more information about last question & Labs?

100% of the questions are from here but you need to review all questions including old ones.
Got GLBP lab with 15 second delay on prempt. show command is working.

don’t trust the OSPF config claims here what people got so far :

GLBP:
one of the set of question is a sim lab – it related to GLBP configuration between two SW L3 and ensure whenever the primary router fail, it will take minimal of 15s delay for that router take control back when it recovered. (I got this one)

LACP:
configure Etherchannel using LACP, Make the VLAN 10 on this trunk link as Native as there had to be untagged traffic and last thing was to set spanning tree for one of the switches as root secondary.

EEM labs (?):
create EEM to archive syslog messages when a user is doing config changes (it must include the user login)
The lab required you to create an EEM script to bring a loopback interface back up if it got shut down.

I read BGP on chinese forum but cannot confirm.

config are all very simple no more than 4-5 commands and show command is available

Good luck all takers

please share updated dumps

Please Share New Questions and Sim Lab plssss.

I passed today in Romania with a score above 90%. I received 6-7 new questions which were not at all in the dumps but they were piece of cake if you know the content (if you understood the answers to the questions in the dumps). I also received a lab in which I had to do 2 things: establish a NetFlow (just a couple of commands) and also to archive the config after a change. I cheated a bit (in my opinion) as I did not use EEM but pure archive and I parsed the “show user” appended to the filename. In that section I got 100% thus they swalloed it. To be honest, I think this is my last renewal (after 20 years) as the effort invested is not worth it. I deal with Cisco devices every day and still think it does not worth it. I am not in search of a new job or prove anything to anyone. I would like to thank Digitaltut and all the people here sharing the content and their experience. It makes the exam easier in the context in which the exam tests if you miss a point or a comma, something which in reality you can rely on compilers and built-in help. I wish you good luck to everyone. The dumps are ABSOLUTELY VALID (I prepared all of them, understanding all the finest details before I went to the exam).

There are no new questions everything is in here, there might be slight variation of the question but overall everything is here.

Sims are simple 4-5 lines of codes, you have show command and includes:

-GLBP : set glbp+preempt+preempt delay
-etherchannel: set PCAP + native VLAN
-EEM: unshut shut loopback
-EEM2(not confirmed): Archive config change
-BGP: rumors

good luck

Hi Guys, who took the exam recently?
Please share your experience .. unfortunately we still don’t have any reliable information about LAB.

where can I find more information about last question & Labs?

@Passed, @meow, @PPPoE, @all good
I just joined the premium platform and studying the questions for my exams over the weekend, can you guys share more light on the labs that has been the buzz word for the last few days? Are these in the tutorial sections or where? I just want to cover all the basis.

Hi All what does it mean everything is here ? WHERE ?

Cisco has removed the verbiage from their site regarding the format of the exam and questions. It previously listed as: Multiple-Choice Single Answer, Multiple-Choice Multiple Answer & Drag and Drop.

Makes me wonder if these are just “unscored” test questions they are adding to the pool.

Cisco Live is in a few weeks and they are going to announce the next changes to the exam. This version of the exam was released in February of 2020. In the past most exams were refreshed every 3 years. I would expect a new exam or format to be announced in June for February of 2023 release.

@all good: I believe, it means the premium section.

@all good

what are the -BGP: rumors?

I just took the exam and luckily pass. Study the Drag and Drap all of them. I got a simulation regarding the setup of HRSP on the router and NetFlow.

bgp rumors are the sim containing 3 routers, r1, r2 and r3. R1 and r3 are in same AS. You only have access to r2. R1 and R3 must be able to ping each others loop backs. Pretty much similar to what is on ipwithease and the examples of AS over ride.

to Cisco207: did you get 102 questions +1 Lab? or there were less number of questions ?
Did you solve that LAB?

@Digitaltut, @admin or any other authorities can you please confirm if these sim labs or real or not? There is so much crap and fakes on these posts and it’s very distracting and off putting and difficult who to trust or not.

@CruxMay

Labs Sims were posted on reddit also.
They are legit

CCNP-2022 LINK PLEASE

hi, @CCNP-2022 could you share the reddit’s link related to the lab sims.

@the Eagles

reddit.com/r/ccnp/comments/uugyv3/biweekly_rccnp_exam_passfail_discussion/

I got 102 questions and I completely pass on the simulation question because I did not have enough time left.

I have passed my exam. Thank you Digitatut.

Please do not memorise the answer by hard as there will be tweaks to the existing qns, I est there are around 15-20 new questions.

I got a VRRP SIM which I passed on.

share you experience Sim Lab and command config pls.

hi just passed the exam here in USA, thanks a lot to digital Tut,
there was 3-4 new questions. rest all were from the Digital Tut,
i got one BGP Simulation, i was not able to do it, it was like Site 1 AS1 connected to HQ AS2 and then AS2 was connected to another Site 3 which is also in AS1. task was that we need to able to ping the Loop back address from site 1 to Site 3. we are only allowed to configure router at HQ.

@ Akki: You got 102 Q + one additional Lab in your exam?

Hi all, congrats for who’ve passed the exam!!

Can anyone who’ve passed recently share lab or sim question/s ???

Hi @Faniii is there lab or sim questions??

Can you please share the dump @Barnes

For those wanting assistance.
—————LAB:EEM——————-
track 1 interface Loopback0 line-protocol

event manager applet EEM_Example
event track 1 state down
action 1.0 cli command “enable”
action 2.0 cli command “conf t”
action 3.0 cli command “int lo0”
action 4.0 cli command “no sh”

*show event manager statistics policy*
————LAB:Etherchannel———–
vlan 200
name native_vlan

interface range ethernet0/0-13
channel-group 1 mode desirable
interface Port-channel1
switchport trunk encapsulation dot1q
switchport mode trunk
switchport trunk native vlan 20

*show etherchannel summary

————–LAB:GLBP———-

DSW1:
interface vlan100
glbp 1 ip 192.168.1.37
glbp 1 priority 110
glbp 1 preempt delay minimum 15

DSW2:k
interface vlan100
glbp 1 ip 192.168.1.3

*show glbp brief

————–Lab:Netflow_v9———–
flow record R
match ipv4 destination address
match ipv4 source address

flow exporter E
destination 10.1.1.1

flow monitor M
exporter E
record R

interface Ethernet0/0
ip flow monitor M
*show ip cache flow
*show ip flow export
*show ip flow top-talkers*

————–Lab:Netflow_v5———–
ip flow-export destination 10.1.1.1 2055
ip flow-export source Ethernet0/29
ip flow-export version 5
ip flow-cache timeout active 1

interface Ethernet0/0
ip flow ingress

————-Lab:Netflow-Archive config——–
archive
path ftp://192.168.1.1/$h-$t
write-memory

*show archive

————-BGP: as-override——–
SiteA/B as200, access ISP(PE1-P-PE2)，ISP as100
It should be configured PE1 and PE2 as BGP neighbor as override
Google Reference ipwithease bgp as override

*show ip bgp

—————LAB:EEM——————-
track 1 interface Loopback0 line-protocol

event manager applet EEM_Example
event track 1 state down
action 1.0 cli command “enable”
action 2.0 cli command “conf t”
action 3.0 cli command “int lo0”
action 4.0 cli command “no sh”

*show event manager statistics policy*

I passed my exam today
There were a lot of new questions in the exam, there were a few questions that changed answers to existing questions, there were new simulation questions, a question about setting up EEM, a problem with automatically unlocking the loopback interface, all good luck.

@V ,, Did you study all the other questions from the Architecture Questions to the Drag Drop Questions 2 sections ?

HI thank you tut team passed my exam today. All questions from here but some questions have bit of variation . If you go through all proper you will pass it . with SIM there was an OSPF simlet.

Yes, thanks George, Passed my test this morning using the same practice test, all the question are identical.

Friends, is it working the TAB button, and ? button on the simulator in the exam?

@SpotoMay

Yes you can use ? To provide further context

Can someone confirm if there are 100qa PLUS labs? Or do the Labs reduce the number of the questions?

@sim ,, explain about BGP or Guide more this lab sim pls

————-BGP: as-override——–
SiteA/B as200, access ISP(PE1-P-PE2)，ISP as100
It should be configured PE1 and PE2 as BGP neighbor as override
Google Reference ipwithease bgp as override

*show ip bgp

Hello guys, I will be taking ENCOR exam soon. Can someone share the latest, valid dump on this email? God Bless You generous people of digitaltut

paul.jev@yahoo(dot)com

Hello guys, I will be taking ENCOR exam soon. Can someone share the latest, valid dump on this email below? God Bless You generous people of digitaltut

paul.jev@yahoo(dot)com

I passed the exam yesterday, there were 8 new question in my exam which are not exist here in digitaltut but 7 of them were very easy if you understand all the explanation for all the question here.

I got many question from the non-premium sections (Arch to D&D 2) along with the premium section (4 to 10), so you have to study all the questions here in digitaltut and to understand the explanation.

I got a Lap which requires to configure HSRP over VLAN100 between two distribution switches and you have to configure 192.168.1.1 as virtual IP and change the priority at DSW1 to be 110 and you have to configure preempt at DSW1 along with tracking to the line-protocol and decrement 20 from the priority in order for DSW2 to get the active rule.

Digitaltut is 93% valid to pass the exam. thanks for the help.