Share your ENCOR Experience

ty. passed yesterday. moving on to work on CISSP cert. I’d say maybe 10 percent I didn’t recognize or seemed somewhat different than I remembered?

right now premium is valid. if you score 90 percent or more 10 times with the premium 100 componsite, you will pass. few new ones. didn’t see more than 10 maybe?

thanks.

Congrats but that is different to what Holland writes. Congrats, Holland.

@Holland, did you have the premium? They updated some new questions in the premium. So you say none of those newly updated questions came?

have taken exam today and passed somehow. Please do review on recent vce and premium then master it. You must have some understanding as well because there are plenty of new questions. Thanks Digitaltut and see you again after 3 years

@CCNP yes, I had premium, many question from Part 9 was in the exam, but also many new questions not in Digitaltut premium

there’s no score posted from the result. Only percentage on each topics. You just need a passing remark.

Just Passed the test. I used premium, you can pass if you study the composites. Several questions from the section 9. Only got aroud 5-10 new or old questions with different options. Good luck Everyone

just knowing vxlan is dataplane and lisp is control plane takes care of 3-4 questions you’ll see.

I passed exam today. I encounter new questions not available in digitaltut premium.

Congrats. What was your study material?

@Mabele can u share study material ?

Can someone kindly please share the new dumps?

Just passed the exam. Over 90% in all except secuirty (85%). All questions from premium except for few. Especially more from section 9 40-78 qs. I will paste the questions only ones that are not in here along with answers.

Rotuer1$ ssh -s {email not allowed}.3 -p 830 netconf
{email not allowed}.3’s password: cisco123

urn:ietf:params:netconf:base:1.0
urn:ietf:params:netconf:base:1.1
urn:ietf:params:netconf:capability:writable-running:1.0
urn:ietf:params:netconf:capability:xpath:1
urn:ietf:params:netconf:capability:validate:1.0
urn:ietf:params:netconf:capability:validate:1.1
urn:ietf:params:netconf:capability::rollback-on-error:1.0
—snip—

2870]]>]]>

Refer to exhibi. An Engineer tries to log into router R1. which configuration enables a successful login?
Answer A: R1# netconf-yang
username admin privilege 15 secret csico123
aaa new-model
aaa authorization exec defualt local

B. R1# username admin privilege 15
aaa authorization exec defualt local

C. R1# aaa new-model aaa authorization exec defualt local
enable aaa admin privilege 15

D. R1# username admin privilege 15
aaa authorization exec defualt local
netconf-yang

Refer to the exhibit.

An engineers reaching network 172.16.10.0/24 via the R1-R2-R4 path. Which configuration forces the traffic to take a path of R1-R3-R4?

A. R1(config)#route-map RM_AS_PATH_PREPEND
R1(config-route-map)#set as-path prepend 200 200
R1(config-route-map)#exit
R1(config)#router bgp 100
R1(config-router)#neighbor 12.12.12.2 route-map RM_AS_PATH_PREPEND in
R1(config-router)#end
R1#clear ip bgp 12.12.12.2 soft in

B. R1(config)#router bgp 100
R1(config-router)#neighbor 13.13.13.3 weight 1
R1(config-router)#end

C. R2(config)#route-map RM_MED permit 10
R2(config-route-map)#set metric 1
R2(config-route-map)#exit
R2(config)#router bgp 200
R2(config-router)#neighbor 12.12.12.1 route-map RM_MED out
R2(config-router)#end
R2#clear ip bgp 12.12.12.1 soft out

D. R1(config)#route-map RM_LOCAL_PREF permit 10
R1(config-route-map)#set local-preference 101
R1(config-route-map)#exit
R1(config)#router bgp 100
R1(config-router)#neighbor 13.13.13.3 route-map RM_LOCAL_PREF in
R1(config-router)#end
R1#clear ip bgp 13.13.13.3 soft in

Answer B

I got this on my exam too

Refer to the exhibit.

… —config missing—
Hello due in 00:00:07
Supports Link-local Signaling (LLS)
Cisco NSF helper support enabled
IETF NSF helper support enabled
Index 1/2/2, flood queue length 0
Next 0x0(0)/0x0(0)/0x0(0)
Last flood scan length is 0, maximum is 0
Last flood scan time is 1 msec, maximum is 1 msec
Neighbor Count is 0, Adjacent neighbor count is 0
Suppress hello for 0 neighbor(s)
An engineer configures OSPF and wants to verify the configuration. Which configuration is applied to this device?

A. R1(config)#interface Gi0/1
R1(config-if)#ip ospf 1 area 0
R1(config-if)#no shutdown

B. R1(config)#router ospf 1
R1(config-router)#network 0.0.0.0.0 0.0.0.0 area 0
R1(config-router)#no passive-interface Gi0/1

C. R1(config)#interface Gi0/1
R1(config-if)#ip ospf enable
R1(config-if)#ip ospf network broadcast
R1(config-if)#no shutdown

D. R1(config)#router ospf 1
R1(config-router)#network 192.168.50.0 0.0.0.255 area 0

Answer: A

I pasted some questions here but they didn’t appear. I passed today. Over 85% in all 100 in some. All questions here. 5 questions not here which i pasted but it didnt appear. Also access list question the answer is seq5 not the one where you just put the statement at the end.

Router#show access-list
Extended IP access list 100
10 permit ip 192.168.0.0 0.0.255.255 any
20 permit ip 172.16.0.0 0.0.15.255 any

Answer is

Router(config)#access-list 100 seq 5 permit ip host 172.20.10.1 any log
Router(config)#interface GigabitEthernet0/1
Router(config-if)#access-group 100 in

Refer to exhibi. An Engineer tries to log into router R1. which configuration enables a successful login?
**A: R1# netconf-yang
username admin privilege 15 secret csico123
aaa new-model
aaa authorization exec defualt local

B. R1# username admin privilege 15
aaa authorization exec defualt local

C. R1# aaa new-model aaa authorization exec defualt local
enable aaa admin privilege 15

D. R1# username admin privilege 15
aaa authorization exec defualt local
netconf-yang

Answer A

Switch>enable
Switch#conf t
Switch(config)# int gi1/10
Switch(config-if)# switchport mode trunk
Switch(config-if)# switchport trunk allowed vlan10,20,30
Switch(config-if)# exit
Switch(config)# monitor session1 type erspan-source
switch(config-mon-erspan-src)# destination source1
switch(config-mon-erspan-src)# source vlan10
switch(config-mon-erspan-src)# source vlan20
switch(config-mon-erspan-src)# filter vlan30
switch(config-mon-erspan-src)# destination
switch(config-mon-erspan-src-dst)# erspan-id 100
switch(config-mon-erspan-src-dst)# origin ip address 10.1.0.1
switch(config-mon-erspan-src-dst)# ip prec 5
switch(config-mon-erspan-src-dst)# ip ttl 32
switch(config-mon-erspan-src-dst)# mtu 1500
switch(config-mon-erspan-src-dst)# ip address 10.10.0.1
switch(config-mon-erspan-src-dst)# vrf 1
switch(config-mon-erspan-src-dst)# no shutdown
switch(config-mon-erspan-src-dst)# end

Refer to the exhibit: An engineer configures a trunk and proceeds to configure an ERSPAN session to monitor vlan10,20 and 30. which command must be added to complete the configuration?

A: Device(config-mon-erspan-src-dst)# no vrf1
B: Device(config-mon-erspan-src-dst)# erspan-id 6
C: Device(config-mon-erspan-src-dst)# mtu 1460
*D Device(config-mon-erspan-src-dst)# no filter vlan 30

Answer D

Refer to the Exhibit. which python code parses the response and prints “18:32:21.474 UTC Sun Mar 10 2019”?

*A: print(response[‘result’][‘body’][‘simple_time’])

B: print(response[‘jsonrpc’][‘body’][‘simple_time’])

C: print(response[‘body’][‘simple_time’])

D: print(response[‘result’][0][‘simple_time’])

Answer A

Which part did most the questions come from?

Section 4-9. Mostly 9. There were like 20% from other individual sections. So I would say learn all.

Refer to the exhibit. An administrator troubleshoots intermittent connectivity from internal hosts to an external public server. Some internal hosts can connect to the server while others receive an icmp host unreachable message, and these hosts change over time. What is the cause of the issue?
A. The NAT Acl and NAT Pool share the same name.
B. The translation does not use address overloading. << Answer
C. The NAT ACL does not match all internal hosts.
D.The NAT pool netmask is excessively wide.

ip sla 100
Udp-echo 10.10.10.15 6336
frequency 30

Refer to the exhibit. An engineer has configured IP SLA for udp echoes. Which command is needed to start the monitoring?
A. Ip sla schedule 100 start-time now life 30.
B. Ip sla schedule 100 start-time now life forever. <<<Answer
C. Ip sla schedule 30 start-time now life 30.
D. Ip sla schedule 100 life forever.

A large campus network has deployed two wireless LAN controllers to manage the wireless network. WLC1 and WLC2 have been configured as mobility peers. A client device roams from AP1 on WLC1 to AP2 on WLC2, but the controller’s client interfaces are on different VLANs. How do the wireless LAN controllers handle the inter-subnet roaming?
A WLC1 marks the client with an anchor entry in its own database. The database entry is copied to the new controller and marked with a foreign entry on WLC2. << Answer.
B WLC2 marks the client with an anchor entry in its own database. The database entry is copied to the new controller and marked with a foreign entry on WLC1.
C: WLC2 marks the client with an foreign entry in its own database. The database entry is copied to the new controller and marked with a anchor entry on WLC1.
D: WLC1 marks the client with an foreign entry in its own database. The database entry is copied to the new controller and marked with a anchor entry on WLC2.

Refer to the exhibit: An engineer configures a trunk and proceeds to configure an ERSPAN session to monitor vlan10,20 and 30. which command must be added to complete the configuration?

A: Device(config-mon-erspan-src-dst)# no vrf1
B: Device(config-mon-erspan-src-dst)# erspan-id 6
C: Device(config-mon-erspan-src-dst)# mtu 1460
D Device(config-mon-erspan-src-dst)# no filter vlan 30 << Answer

Just passed now, i would say in my case was online at home and i got a lot of new questions around 30% of (106q in my case total) was new i didt see in any dump here and raterD file. D&D are almost the same.

Questions about IP SLA config
New BGP questions
New OSPF questions
a more scripting YANG and REST config.

For one momment i think i failed, if you all look all the questions i said all on raterD file and undertand the concept for sure youll pass also.

See you in 3 years, thank you a lot @CCPN @RaterD and many other who shared questions here.

Congrats and all the best moving forward. 30% is a lot.

passed the exam today. can’t really see my total score but there quite a few new question not seen here or other dumps site. i would say 80% of the qns found in here are still valid. some are same qns but different answer choices.

@ENCOR or anyone who just took the exam

Can you confirm the new questions above posted by CCNP?

Did you see any of the those questions appeared on your exam?

@CCNP Where did you get those questions? Thanks for the update mate.

@CCNP Thanks for the new questions. How come you remember all new questions that you encountered on your exam? Do you have other sources other than premium or ratedr’s?

@Digitaltut Please verify the answers posted by CCNP above.

Congrats! Can you guys verify the questions above from CCNP?

Please guys verify the questions that CCNP posted, are these the questions you got on the test?

Yes the questions that @CCNP posted are present but as I said verify all questions on RaterD file I mean all the 670q and get prepared to answer the variations cuz many questions are almost the same but couple different answers and order also.

Hey and do not forget! Verify the answers also ok raterD file, many questions are wrong also go to digitalTute, google cisco documents in some of them specially the news

What about this two questions from from part 7 that are missing exhibit??? we don’t have answers for them.

1.Refer to the exhibit.

An engineers reaching network 172.16.10.0/24 via the R1-R2-R4 path. Which configuration forces the traffic to take a path of R1-R3-R4?

A.R1(config)#route-map RM_LOCAL_PREF permit 10
R1(config-route-map)#set local-preference 101
R1(config-route-map)#exit
R1(config)#router bgp 100
R1(config-router)#neighbor 13.13.13.3 route-map RM_LOCAL_PREF in
R1(config-router)#end
R1#clear ip bgp 13.13.13.3 soft in
B.R1(config)#router bgp 100
R1(config-router)#neighbor 13.13.13.3 weight 1
R1(config-router)#end
C.R2(config)#route-map RM_MED permit 10
R2(config-route-map)#set metric 1
R2(config-route-map)#exit
R2(config)#router bgp 200
R2(config-router)#neighbor 12.12.12.1 route-map RM_MED out
R2(config-router)#end
R2#clear ip bgp 12.12.12.1 soft out
D.unknown
E.R1(config)#route-map RM_AS_PATH_PREPEND
R1(config-route-map)#set as-path prepend 200 200
R1(config-route-map)#exit
R1(config)#router bgp 100
R1(config-router)#neighbor 12.12.12.2 route-map RM_AS_PATH_PREPEND in
R1(config-router)#end
R1#clear ip bgp 12.12.12.2 soft in

2.Refer to the exhibit.

… —config missing—
Hello due in 00:00:07
Supports Link-local Signaling (LLS)
Cisco NSF helper support enabled
IETF NSF helper support enabled
Index 1/2/2, flood queue length 0
Next 0x0(0)/0x0(0)/0x0(0)
Last flood scan length is 0, maximum is 0
Last flood scan time is 1 msec, maximum is 1 msec
Neighbor Count is 0, Adjacent neighbor count is 0
Suppress hello for 0 neighbor(s)

An engineer configures OSPF and wants to verify the configuration. Which configuration is applied to this device?

A. R1(config)#router ospf 1
R1(config-router)#network 192.168.50.0 0.0.0.255 area 0
B. R1(config)#interface Gi0/1
R1(config-if)#ip ospf enable
R1(config-if)#ip ospf network broadcast
R1(config-if)#no shutdown
C. unknowncorrect
D. R1(config)#interface Gi0/1
R1(config-if)#ip ospf 1 area 0
R1(config-if)#no shutdown
E. R1(config)#router ospf 1
R1(config-router)#network 0.0.0.0.0 0.0.0.0 area 0
R1(config-router)#no passive-interface Gi0/1

What happens when a FlexConnect AP changes to standalone mode?
(A). All controller-dependent activities stop working except the DFS.
(B). All client roaming continues to work
(C). Only clients on central switching WLANs stay connected.
(D). All clients on an WLANs are disconnected

Question 4
Which definition describes JWT in regard to REST API security?

A. an encrypted JSON token that is used for authorization
B. an encoded JSON token that is used for authentication
C. an encoded JSON token that is used to securely exchange information (correct)
D. an encrypted JSON token that is used for authentication

What are the correct answers for this two questions?

A and C

@ENCOR which questions that CCNP posted above are actually included in your exam?

ENCOR has already confirmed that the questions were there.

@ENCOR thank you.

Passed today. Few extra questions related to bgp.
To pass you will need this site + premium
+ knowledge.
Good luck to everyone

Router#show access-list
Extended IP access list 100
10 permit ip 192.168.0.0 0.0.255.255 any
20 permit ip 172.16.0.0 0.0.15.255 any
Which command set must be added to permit and log all traffic that comes from 172.20.10.1 in interface GigabitEthernet0/1 without impacting the functionality of the access list?

Option A

Router(config)#ip access-list extended 100
Router(config-ext-nacl)#5 permit ip 172.20.10.0 0.0.0.255 any log
Router(config)#interface GigabitEthernet0/1
Router(config-if)#access-group 100 in

Option B

Router(config)#no access-list 100 permit ip 172.16.0.0 0.0.15.255 any
Router(config)#access-list 100 permit ip 172.16.0.0 0.0.15.255 any log
Router(config)#interface Gigabit Ether net0/1
Router(config-if)#access-group 100 in

Option C

Router(config)#access-list 100 permit ip host 172.20.10.1 any log
Router(config)#interface GigabitEthernet0/1
Router(config-if)#access-group 100 in

Option D

Router(config)#access-list 100 seq 5 permit ip host 172.20.10.1 any log
Router(config)#interface GigabitEthernet0/1
Router(config-if)#access-group 100 in

A.Option A
B.Option B
C.Option C
D.Option D

C ot D?

@cisco_ccnp answer is d. I chose C on the exam and im pretty sure it was wrong.

@CCNP thanks.

Refering to the question:

“Which command set must be added to permit and log all traffic that comes from 172.20.10.1 in interface GigabitEthernet0/1 without impacting the functionality of the access list?”

You should know that there is no “(config)#access-list 100 seq 5” command in the CLI.

How soon should I purchase the dumps for the CCNP exam? TIA

I don’t get your point. What are you trying to say?