ROUTE FAQs & Tips
In this article, I will try to summarize all the Frequently Asked Questions in the ROUTE 300-101 Exam. Hope it will save you some time searching through the Internet and asking your friends & teachers.
1. Please tell me how many questions in the real ROUTE exam, and how much time to answer them?
There are 50 questions, including 4 lab-sims. You have 120 minutes to answer them but if your native language is not English, Cisco allows you a 30-minute exam time extension (150 minutes in total).
2. How much does the ROUTE 300-101 cost? And how many points I need to pass the exam?
This exam costs $300. You need at least 790/1000 points to pass this exam.
3. I passed the ROUTE exam, will I get a certificate for it?
No, Cisco does not ship ROUTE Exam certificate, it only ships you a certificate after completing the full CCNP track of 3 exams (ROUTE, SWITCH & TSHOOT) within three years. Once again we have to notice that you need to finish these three exams within three years (not nine years). Many candidates misunderstand this and think they have nine years to complete three exams.
4. Which sims will I see in the ROUTE exam?
The popular sims now are Policy Based routing sim, EIGRP OSPF Redistribution sim, OSPF Evaluation Sim and EIGRP Evaluation Sim and please notice that the IP addresses, router names may be different (it is also true for Drag and Drop questions)
5. How many points will I get for one sim?
Maybe you will get about 80 to 100 points for each sim, just like the CCNA exam.
6. In the real exam, I clicked “Next” after choosing the answer, can I go back for reviewing?
No, you can’t go back so you can’t re-check your answers after clicking the “Next” button.
7. What is the difference between the old BSCI & the new ROUTE exam?
In the new ROUTE exam, there are no IS-IS, DHCP, Multicast questions so you can ignore them if you are reading old BSCI books. In fact, DHCP & Multicast are good topics and maybe you will have a chance to learn about them in other Cisco exams.
8. Can I use short commands, for example “conf t” instead of “configure terminal”? Will I get full mark for short commands?
From the comments on this site, maybe you will get full mark for short commands. But sometimes short commands don’t work so please be careful with them. We highly recommend you should learn the full commands.
9. What are your recommended materials for ROUTE?
There are many materials for learning ROUTE but below are popular materials that many candidates recommend.
Books
CCNP ROUTE Official Certification Guide
ROUTE Student Guide
CCNP ROUTE Portable Command Guide
CCNP Route Quick Reference Sheet
Video training
CBT Nuggets
Simulator (all are free)
GNS3 – the best simulator for learning ROUTE
Packet Tracer
10. How much time should I spend on each sim?
You should not spend more than 15 minutes for each sim. Recall that you only have 90 minutes so if you spend 15 minutes for each sim x 4 sims = 60 minutes. The 30 minutes left is for solving 46 multiple choice & drag-and-drop questions. If you are not a native English speaker and have 30-minute expansion (ask the mentor to confirm) than you can spend 20 minutes for each sim.
11. Can I pass without doing sims?
As mentioned above, each sim will cost you from 80 to 100 points. In the real exam you will have to solve 4 sims that give from 320 to 400 points. Suppose you answer all other questions perfectly then you will get 600 to 680 points but the passing score is 790. It means that you surely fail if ignore them.
From the calculation above, if you miss only one sim the chance to pass is average but if you miss two, the chance to pass is very, very low.
12. Are the exam questions the same in all the geographical locations?
Yes, the exam questions are the same in all geographical locations. But notice that Cisco has a pool of questions and each time you take the exam, a number of random questions will show up so you will not see all the same questions as the previous exam.
13. I don’t want to lose points so should I use the “copy running-config startup-config” after finishing each lab-sim?
In the ROUTE exam, we can’t use that command so surely you will not lose any points if not using that command.
14. I passed the ROUTE exam. Do you have any site similar for CCNP exams?
We have certprepare.com for SWITCH, networktut.com for TSHOOT, voicetut.com for CCNA Voice, securitytut.com for CCNA Security, rstut.com for CCIE Written & Lab, dstut.com for CCDA. Hope you enjoy these sites too!
15. Why don’t I see any questions and answers on digitaltut.com? I only see the explanation…
Because of copyrighted issues, we had to remove all the questions and answers. You can download a PDF file to see the questions at this link: http://www.digitaltut.com/encor-questions-and-answers
Is there anything you want to ask, just ask! All of us will help you.
Someone give me the link to the latest question and answers pdf from this site. Thank you
can you guys give me latest valid dumps please? Thanks in advance..
Hi,
I put this up about a month ago and still not fixed.
I think the answer above is incorrect.
Question 8, it should be frequency…
A network engineer is asked to create an SNMP-enabled proactive monitoring solution to ensure that jitter levels remain between particular boundaries. Which IP SLA option should the engineer use?
A. threshold
B. frequency
C. verify-data
D. timeout
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipsla/configuration/15-mt/sla-15-mt-book/sla_udp_jitter.html#GUID-7E49ED89-D853-4DB5-B997-AF10B40E2C2F
Configuring a Basic UDP Jitter Operation on a Source Device
SUMMARY STEPS
1. enable
2. configure terminal
3. ip sla operation-number
4. udp-jitter {destination-ip-address | destination-hostname} destination-port [source-ip {ip-address | hostname}] [source-port port-number] [control {enable | disable}] [num-packets number-of-packets] [interval interpacket-interval]
5. frequency seconds
6. end
7. show ip sla configuration [operation-number]
please i cant see the share network experence tab
where is the link for v2.0 share experience gone ?
stfu everyone.
Passed with 8xx. I only study digitut questions. Lab the same. Mostly valid. Hahaha
Where the topic – digitaltut route 300-101 “share your experience” ?
https://www.digitaltut.com/share-your-route-v2-0-experience
I download on the site Route_Apr_2016 but I see that there are lots of change.
Do you know if there will be a new dumps available from the site Digitaltut ?
thanks by advance.
CCNP.RS.300-101.NetStudy.2017.06.13.Q353
www . file-upload . com / hlguhp4l5rm6
www . file-upload . com / hlguhp4l5rm6
it suport only premium users
@Gavin when did u take the exam? And were the new ccnp umps updated?
PLease help me to solve the following questions and suggest the correct answers.
1. The enterprise network WAN link has been receiving several denial of service attacks from both IPv4 and IPv6 sources. Which three elements can you use to identify an IPv6
packet via its header, in order to filter future attacks? (Choose three.)
A. Traffic Class
B. Source address
C. Flow Label
D. Hop Limit
E. Destination Address
F. Fragment Offset
Correct Answer: BCE or ACE
2. Other than a working EIGRP configuration, which option must be the same on all routers for EIGRP authentication key role over to work correctly?
A. SMTP
B. SNMP
C. Passwords
D. Time
Correct Answer: C or D
3. Which two reasons for IP SLA tracking failure are likely true? (Choose Two)
A. The source-interface is configured incorrectly.
B. The destination must be 172.30.30.2 for icmp-echo.
C. A route back to the R1 LAN network is missing in R2.
D. The default route has wrong next hop IP address.
E. The threshold value is wrong.
Correct Answer: BE or AC
4. A network engineer enables OSPF on a Frame Relay WAN connection to various remote sites, but no OSPF adjacencies come up. Which two actions are possible solutions for this issue? (Choose Two)
A. Change the network type to point-to-multipoint under WAN interface.
B. Enable virtual links.
C. Change the network type to nonbroadcast multipoint access.
D. Configure the neighbor command under OSPF process for each remote site.
E. Ensure that the OSPF process number matches among all remote sites
Correct Answer: CD or AD
5. In a point-to-multipoint Frame Relay topology, which two methods ensure that all routing updates are received by all EIGRP routers within the Frame Relay network? (Choose Two)
A. Use statically defined EIGRP neighbors on the hub site.
B. Create separate address families.
C. Disable split horizon.
D. Use sub interfaces.
E. Disable EIGRP auto summary.
Correct Answer: AC or CD
6. DHCPv6 can obtain configuration parameters from a server through rapid two-way message exchange. Which two steps are involved in this process? (Choose Two)
A. solicit
B. advertise
C. request
D. auth
E. reply
Correct Answer: AC or AE
7. When unicast reverse path forwarding is configured on an interface, which action does the interface take first when it receives a packet?
A. it verifies that the source has a valid VEF adjacency.
B. It checks the egress access lists.
C. it verifies a reverse path via the FIB to the source.
D. It checks the ingress access lists.
Correct Answer: A or C
8. Which two GRE features can you configure to prevent fragmentation? (Choose Two)
A. IP MTU
B. MTU ignore
C. TCP MSS
D. UDP windows sizes
E. MTUD
F. DF bit clear
Correct Answer: CF or CE
9. Which configuration can you apply to a device so that it always blocks outbound web traffic on Saturdaysand Sundays between the hours of 1:00 AM and 11:59 PM?
Correct Answer: B or C
10. Using new backup router in spite of faulty one in ospf domain but relationship with neighbour in one interface only not working , what is the reason of this problem? (choose 2)
A. area Id mismatch
B. authentication mismatch
C. process id of ospf not match
D. ospf timers not match
Correct Answer: AB or AD
11. Which two commands must you configure on a DMVPN hub to enable phase 3? (Choose two)
A. ip nhrp interest
B. ip nhrp redirect
C. ip nhrp shortcut
D. ip network-id
E. ip nhrp map
F. ip redirects
Correct Answer: DE or BC
12. After testing various dynamic IPv6 address assignment methods, an engineer decides that more control is needed when distributing addresses to clients. Which two advantages
does DHCPv6 have over EUI-64 (Choose two.)
A. DHCPv6 requires less planning and configuration than EUI-64 requires.
B. DHCPv6 allows for additional parameters to be sent to the client, such as the domain name and DNS server.
C. DHCPv6 providers tighter control over the IPv6 addresses that are distributed to clients.
D. DHCPv6 does not require the configuration of prefix pools.
E. DHCPv6 does not require neighbor and router discovery on the network segment.
Correct Answer: AB or BC
13. Which option must be configured on a target device to use time stamping to accurately represent response times using IP SLA ?
A. Responder
B. Jitter value
C. TCP Connect
D. ICMP Echo
Correct Answer: A or D
14. Consider this scenario.
TCP traffic is blocked on port 547 between a DHCPv6 relay agent and a DHCPv6 server that is configured for prefix delegation. Which two outcomes will result when the relay agent is rebooted? (Choose two)
A. Routers will not obtain DHCPv6 prefixes.
B. DHCPv6 clients will be unreachable.
C. Hosts will not obtain DHCPv6 addresses.
D. The DHCPv6 relay agent will resume distributing addresses.
E. DHCPv6 address conflicts will occur on downstream clients.
Correct Answer: AD or AC
15. Refer to the exhibit. Router DHCP is configured to lease IPv4 and IPv6 addresses to clients on ALS1 and ALS2. Clients on ALS2 receive IPv4 and IPv6 addresses. Clients on ALS1 receive IPv4 addresses. Which configuration on DSW1 allows clients on ALS1 to receive IPv6 addresses?
A. DSW1 (config-if)# ipv6 helper address 2002:404:404::404:404
B. DSW1 (config)#ipv6 route 2002:404:404::404:404/128 FastEthernet 1/0
C. DSW1 (dhcp-config)# default-router 2002:A04:A01::A04:A01
D. DSW1 (config)# ipv6 dhcp relay destination 2002:404:404::404:404 GigabitEthernet 1/2
Correct Answer: C or D
16. R1 is unable to ping interface S0/0 of R2. What is the issue the configuration that is shown here?
A. The route-target configuration command is missing.
B. The interface IP addresses are not in the same subnet.
C. the syntax of the ping command is wrong.
D. The default route configuration is missing.
E. The serial interfaces belong to the global table instead of vrf Yellow.
Correct Answer: D or E
17. In which scenario can asymmetric routing occur?
A. active/active firewall setup
B. single path in and out of the network.
C. active/standby firewall setup
D. redundant routers running VRRP
Correct Answer: A or D
18. what are the characteristics of pap and chap (choose two)?
A. PAP provides a challenge to the client
B. CHAP provides a challenge to a client
C. PAP can be used by a TACACS+ for with
D. PAP requires a username and optional password
E. CHAP requires a username and optional password
Correct Answer: BC or BD
19. Which three NTP operating modes must the trusted-Key command be configured on for authentication to operate properly? (Choose Three)
A. interface
B. client
C. peer
D. server
E. broadcast
Correct Answer: BDE or BCE
20. Drag and Drop GRE features order
21. Drag and Drop uRPF mode order
i couldn’t download the pdf file with questions and answears. Digitaltut pls help me.
@admin do we get the access to the theory of every topic here after becoming the premium member??
@All
Are we allowed to show run in all labs? Thanks!
Can someone please share the link for the most recent dumbs
Can someone please share me the CCNP Route latest dums in PDF file on the below mention email ID.
{email not allowed}
Can someone share me the CCNP Route latest dums in PDF format at GK. Kundum 2013 @ gmail. com
Can someone confirm how long i have to pass CCNP Switch and TSHOOT if i have already passed Route ? Is it 3 years or 1 year ?
just cleared my CCNP today……Thanks to 9tut and pass leader 470Q
Hello all … I want CCNP 300-101 (Route) latest dump question. Is there anyone here to send me the pdf file to my Email ID: {email not allowed}
Thanks in advance…
Is there new questions?
@Mkzozo
Is there new questions?
@LAB no new labs still same PBR, EIGRP, OSPF Evaluation and OSPF redistribution. questions all new just check this site 9TUT
Hello, could you send me the latest dumps and crack gns please?
pinkmanreis@ g m a i l . c o m
Hi, send me lastest dumps please
jonomolono@ g m a i l . c o m
Here is the best solution all that you need to passs this exam easily:
VCE And PDF file
Packet Tracer / GNS3 Labs
DOWNLOAD:
https://docs.google.com/document/d/1cp2vtCYSV_21JTZF9D14Ua2gHdijtZjfIDuyVT1NyJg/edit?usp=sharing
New dumps please for CCNP 300-101 heitkrew at gmail dot com
can you tell me the book and author to refer to for ccnp route
Get latest 200-105 question answers in pdf file. https://www.dropbox.com/s/aa5f0fmcnkybobl/Cisco%20200-105%20Dumps%20%20And%20Cisco%20200-105%20Question%20Answers.pdf?dl=0
new dumps please for CCNP 300-101 {email not allowed}
hey Brucewin, do you have the latest dumps for ccnp 300-101? pls let me know. thanks
Hi, somebody can tell me if the questions here on digitaltut are updated?thanks
plz any updated valid dumps for ccnp 300-101? ??????????????????????????????????
{email not allowed}
plz,, is there any update ?
please help me I need ccnp r&s valid dump my mail is {email not allowed}
you guys confuses me .. i am ready for the exam in a couple of days .. i read more more than 500 questions including dumps. is there new questions ? new dumps to wait for? or go ahead for exam?
Confirming the 440q dumps are valid. I used the ones from it Libaries.
hi jarret, when did you take the exam? what questions you had?
help please!
I passed route exam recently, with a score around 800 (so it was pretty tight). I studied from the questions here, CBT nuggets and Chris Bryant guide.
I can confirm that the simulation here were all presents and valid as I would say 80% of the questions (100% of the drag a& drop). I did encounter questions that were not here, but apart from a couple, they were not that difficult. Some at CCNA level (I remember “what is the default username for CHAP with PPPoE?. Choose between 1) Cisco 2) password 3) hostname 4) none. I chose hostname). Some other multiple choice questions I was a bit insecure I admit that drag & drop I might have done some mistakes as I did not remember exactly from here. So all in all it might have been that I would have gotten a better score if I had remembered better the answers of those.
If you have a clue and did not only memorize the questions here you should be fine. Good luck everyone and thanks a lot for the good site and tips!!!!
Hello digitaltut
Do you guys have a site for CCNA CyberOps?
My exam is next week and I need dumps for revision
Thanks
Hi team! Does anyone have a free VCE player app for MacBook ?
I’m preparing for 300-320 exam. Does anybody know whether the exam contains labs? I found dumps with 300+ questions. But no single lab. Thanks in advance.
Passed used the 21q dumps from IT-Libraries
you passed what? explain and help with questions
I was able to pass the exam with the help of you guys, especially Mr. Cisco Kid, Procyber and Its me. 470q dumps is still valid. There’s only 1 new question and if I remember it correctly, it goes somthing like this:
“ip nat inside source list 1 interface f0/0 overload” what type of ACL is this?
a. NAT64
b. PAT
c. Dynamic
d. Static
Tips:
a. Please take time to review the instructions before taking the exam (CAREFULLY), don’t press “NEXT” immediately
b. For MCQ, 470q still valid, 95% of the explanation in 470q at digitaltut are correct
b. Drag and Drop – all in this site and 470q
c. LABs: PBR, OSPF stub, EIGRP/OSPF redistribution – all these can be seen on digitaltut. I SWEAR! (even the same OSPF process ID and EIGRP AS #). Only IP changed.
d. Eval – OSPF rocks! EIGRP: the only thing in that eval is that you cannot use “ip eirgrp topology “, so what I did is perform show ip route in R1 and look for “192.168.46.0” network; this will display the Admin D/FD. With this, it shows I learned 192.168.46.0 via R3. Open R3 and perform show ip route and look for 192.168.46.0. it displayed the Admin D/FD. This FD is the correct advertised distance from R1s perspective
Hope I helped.
@2tch@ng : I would like to recertify my CCNP. A long time without visiting this site, I don’t know how to see questions as well as to be get along on this page. Could you give me a hint?
daoquocsiatgmail.com: Sir/Ma’am, you have to be a premium member to view the questions on this site. 12$/month. However, dumps posted by “Its me” are enough. What I did is I copied the dumps, and review the explanations here.