Drag and Drop
Question 1
Explanation
NAT64 provides communication between IPv6 and IPv4 hosts by using a form of network address translation (NAT). NAT64 requires a dedicated prefix, called NAT64 prefix, to recognize which hosts need IPv4-IPv6 translation. NAT64 prefix can be a Network-specific prefix (NSP), which is configured by a network administrator, or a well-known prefix (which is 64:FF9B::/96). When a NAT64 router receives a packet which starts with NAT64 prefix, it will proceed this packet with NAT64.
NAT64 is not as simple as IPv4 NAT which only translates source or destination IPv4 address. NAT64 translates nearly everything (source & destination IP addresses, port number, IPv4/IPv6 headers… which is called a session) from IPv4 to IPv6 and vice versa. So NAT64 “modifies session during translation”.
Question 2
Explanation
The order of the BGP states is: Idle -> Connect -> (Active) -> OpenSent -> OpenConfirm -> Established
+ Idle: No peering; router is looking for neighbor. Idle (admin) means that the neighbor relationship has been administratively shut down.
+ Connect: TCP handshake completed.
+ Active: BGP tries another TCP handshake to establish a connection with the remote BGP neighbor. If it is successful, it will move to the OpenSent state. If the ConnectRetry timer expires then it will move back to the Connect state. Note: Active is not a good state.
+ OpenSent: An open message was sent to try to establish the peering.
+ OpenConfirm: Router has received a reply to the open message.
+ Established: Routers have a BGP peering session. This is the desired state.
Reference: http://www.ciscopress.com/articles/article.asp?p=1565538&seqNum=3
Question 3
Explanation
The Challenge Handshake Authentication Protocol (CHAP) verifies the identity of the peer by means of a three-way handshake. These are the general steps performed in CHAP:
1) After the LCP (Link Control Protocol) phase is complete, and CHAP is negotiated between both devices, the authenticator sends a challenge message to the peer.
2) The peer responds with a value calculated through a one-way hash function (Message Digest 5 (MD5)).
3) The authenticator checks the response against its own calculation of the expected hash value. If the values match, the authentication is successful. Otherwise, the connection is terminated.
This authentication method depends on a “secret” known only to the authenticator and the peer. The secret is not sent over the link. Although the authentication is only one-way, you can negotiate CHAP in both directions, with the help of the same secret set for mutual authentication.
For more information about CHAP challenge please read our PPP tutorial.
Question 5
Explanation
AAA offers different solutions that provide access control to network devices. The following services are included within its modular architectural framework:
+ Authentication – The process of validating users based on their identity and predetermined credentials, such as passwords and other mechanisms like digital certificates. Authentication controls access by requiring valid user credentials, which are typically a username and password. With RADIUS, the ASA supports PAP, CHAP, MS-CHAP1, MS-CHAP2, that means Authentication supports encryption.
+ Authorization – The method by which a network device assembles a set of attributes that regulates what tasks the user is authorized to perform. These attributes are measured against a user database. The results are returned to the network device to determine the user’s qualifications and restrictions. This database can be located locally on Cisco ASA or it can be hosted on a RADIUS or Terminal Access Controller Access-Control System Plus (TACACS+) server. In summary, Authorization controls access per user after users authenticate.
+ Accounting – The process of gathering and sending user information to an AAA server used to track login times (when the user logged in and logged off) and the services that users access. This information can be used for billing, auditing, and reporting purposes.
Question 6
Question 7
Question 8
Explanation
NAT64 provides communication between IPv6 and IPv4 hosts by using a form of network address translation (NAT). There are two different forms of NAT64, stateless and stateful:
+ Stateless NAT64: maps the IPv4 address into an IPv6 prefix. As the name implies, it keeps no state. It does not save any IP addresses since every v4 address maps to one v6 address. Stateless NAT64 does not conserve IP4 addresses.
+ Stateful NAT64 is a stateful translation mechanism for translating IPv6 addresses to IPv4 addresses, and IPv4 addresses to IPv6 addresses. Like NAT44, it is called stateful because it creates or modifies bindings or session state while performing translation (1:N translation). It supports both IPv6-initiated and IPv4-initiated communications using static or manual mappings. Stateful NAT64 converses IPv4 addresses.
NPTv6 stands for Network Prefix Translation. It’s a form of NAT for IPv6 and it supports one-to-one translation between inside and outside addresses
Question 9
Question 10
Question 11
Question 12
Question 13
@Digital TUT your membership is enough to pass the exam???
Where can i find DHCP and adverse network congestion DnD ?
@RPM
ip dhcp relay information option –> add suboption and the remote ID suboption
ip dhcp relay information check –> Verify relay information option (in forwarded BOOTREPLY)
ip dhcp relay information policy …… –> Define reforwarding rules (for a DHCP relay agent)
ip dhcp relay information subscriber-id –> enable a service provider to add a unique ID
ip dhcp relay information –> configured in global configuration mode applies to all interface
Hi guys,
hopefully all are fine. i want to tell you that i will buy the dumps of CCNP Route 300-101 after 5 days. these dumps are 100% valid and only 224 Questions and Answers, 19 Simulations and only 7 Labs. Total (250) if anyone wants the dumps, please contact me on my email. {email not allowed}
Hi guys,
hopefully all are fine. i want to tell you that i will buy the dumps of CCNP Route 300-101 after 5 days. these dumps are 100% valid and only 224 Questions and Answers, 19 Simulations and only 7 Labs. Total (250) if anyone wants the dumps, please contact me on my email. (email is not allowed so, my email is hafiznabeel.safeint (that is gmail account) ;)
i can’t see the question, its that normal?
New Drag&Drop with PPP on Frame Realy
I found a example like the exam here : https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/wan_frly/configuration/15-mt/wan-frly-15-mt-book/wan-pppofr.html#GUID-1CB0E01F-B4AF-4CF6-9863-D116BBD13C2B. I was the DTE exercise
exercise
interface serial 0
” BLANK ”
encapsulation frame-relay
” BLANK ” — I know there is 2 blank on interface serial 0 but I don’t remember the existing command and the blank
#about sub-interface (it’s write like that in the exam)
” BLANK ”
” BLANK ”
interface Virtual-Template1
ip unnumbered ethernet 0
” BLANK ”
Possibility
D&D 1 : ” no ip address ”
D&D 2 : ” interface serial 0/0.1 point-to-point ”
D&D 3 : ” interface serial 0/0.100 ”
D&D 4 : ” frame-relay interface-dlci 32 ppp virtual-template1 ”
D&D 5 : ” another think about virtual-template ”
D&D 6 : ” ip unnumbered ethernet 0 ”
D&D 7 : ” ppp authentication chap ”
D&D 8 : ” frame-relay lmi-type ansi ”
Answer
interface serial 0
” no ip address ”
encapsulation frame-relay
” frame-relay lmi-type ansi ”
!
” interface serial 0.1 point-to-point ”
” frame-relay interface-dlci 32 ppp virtual-template1 ”
!
interface Virtual-Template1
ip unnumbered ethernet 0
” ppp authentication chap ”
I hope it’s will help you :)
new D&D with stateful and stateless NAT64
This link can help : https://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/enterprise-ipv6-solution/white_paper_c11-676277.pdf (end of page 3 specialy)
With regards to Q7 – see this link http://www.ciscopress.com/articles/article.asp?p=170744&seqNum=5
and it informed that:
“RADIUS combines authentication and authorization and separates accounting, thus allowing less flexibility in implementation.”
Sorlags is absolutely correct. The drag and drop he has mentioned appeared in my failure test just last week. Revise this !!
mandatory check – Drag and drop each NAT64 description from the left onto the corresponding NAT64 type on the right. It was in last week as well.
GROUP Buy @ just 20$
Just passed the CCNP ROUTE exam with 950/1000. the mcq are still very the same here.
Here we go.
Get EXAM MATERIAL at below:
Copy below. Remove asteriks
g*o*o*.*g*l*/kp1zbY
Passed CCNP ROUTE 300-101 lastweek.
Thanks digitaltut for nice introductions and thanks Heisenberg dump which I used is 90% valid.
Anyone who needs can reach me at: networkdummies @ gmail dot com
Question 11 doesn’t look correct to me
+ DHCPv6 Server:
IPv6 address autoconfig
IPv6 enable
+ Client Interface:
IPv6 address
IPv6 DHCP Relay destination
It isn’t clear what it is asking but i would assume it is asking what configuration commands go under what devices.
You are required to set up an IPv6 address on the server, and you also would put any DHCP relay commands there also, to point the client to the correct DHCP source (for the DNS details in this scenario).
The client would then use Enable IPv6 command (often not required on Server side due to other commands enforcing IPv6 anyway). Then the client would use Auto-config to get it’s IPv6 address using the DHCP server that its relayed to)
+ DHCPv6 Client
IPv6 enable
IPv6 address autoconfig
+ DHCP server
IPv6 address
IPv6 DHCP Relay destination
Maybe i am wrong, but it’s just how i see it and there is no explanation on here saying otherwise.
ignore my last comment.
I didn’t realise it was meaning ;
Configuration on the CLIENT FACING INTERFACE
Configuration on the DHCP FACING INTERFACE
it is the same device, i wrongly assumed they meant a client device and a router.
ok
Please i have exam today 300-101, can anyone assist with dumps. Thanks
ifeloofestus @ gmail dot com
Passed today, thanks to Digitaltut
Labs/Sims: PBR, OSPF EIGRP Redistribution and OSPF Evaluation Sim.
IP address changes from what is on digital tut. For redistribution do “sh int” to get the correct bandwidth and delay values.
ACL D&D mGRe, IPSec,MSS D&D
All questions were from here, 4 new questions in the exam.
The OSPF EIGRP redistribution, i types “redistribute eigrp 100 metric-type 1 subnets”. When i do show run it was “redistribute eigrp 100 subnets metric0-type 1” , but I was able to ping though the running config was like that.
can anyone provide the latest dumps ccnp route [ 300-101]
My exam is on Wednesday
Can someone please email me the latest ccnp route dumps
my exam is next week
thanks
a.shareef2000 @ gmail
Anyone looking to pass with a high score, email me
I have summarized:
Official Study Guide – cisco
Rene Molenaar Master book
Chris Bryant’s whole book and video collection’
All Cbtnuggets videos, hands on labs (i pay for the website)
If you want to skip having to read all this stuff,
I have the books already summarized, notes on all the videos, and explanations of all the labs for
CBTNUGGETS – labs
Rene Molenaar’s – labs
I will have for Switch as well.
Email me for samples:
apkey (tech) at gmail.com
PS: I also have a 100 of the most popular questions from the actual test (route, switch)
Hi Guys. If you want to download freedump 300-101 go in my link
htt ps: //w ww.yout ube.co m/wa tch?v=8YAlL G9FYlo
I failed today in the CCNP route exam by reading only the question in 9tut. There are a lot of different questions are not in 9tut. Could anyone send me the latest dump exam or where to find it.
@AlHafidhS – you need to study and learn concepts. Reading only the dumps is not enough to pass. I have studied hard and still failed by a small amount. Preparing for my 3rd attempt at the route exam.
Stateless NAT64 and Stateful NAT64
I got many questions today, keep the chart in memory.
www . examtopics . com/exams/cisco/300-101/view/31/
q 457 in the above url
I passed with 869 today.
I see IPv6 ospf virtual-link, ospf totally-stub, EIGRP
and 5 drag &drops. frame-relay, DHCPv6, NAT64, AAA,and the other.
a lot of questions that I haven’t ever seen in this web
so if you understand all questions this site describes, it is not easy to pass this exam.
but I want to help you, so I describe new questions below
・the difference between OSPFv2 & OSPFv3
・the difference between EIGRPv2 & EIGRPv3
・offset-list in RIPv2
・the problem when CAM timers is lower than ARP timers
・the difference between statefull NAT64 and Stateless NAT64(more specifically, and difficult)
・the problem when EIGRPv2 use on the VRF
otherwise, I never see below
・policy-map
・redistribute
・URPF
・TCP&UDP(maybe one mf them was appeared)
sim and lab is very easy, but options are very difficult
best regards
Hi :). I am from Netherlands and i don’t know how can i disable my signature? Regards :)
some one given new ccnp version exam. please suggest
Hello. And Bye.
Annoying message
{email not allowed}
Hello. And Bye.
Hello i am new user and i would to ask you, How to disable avatar?
Hello i am new user and i would to ask you, How to disable a pm?
hello how too get latest dumps please?
Hello. And Bye.